MPS field of DOEPCTL0 is read only.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to documentation, TX FIFO_number index starts from 1.
For IN endpoint FIFO 0 we use GNPTXFSIZ register for programming
the size and memory start address.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

- For Control Read transfer, the ACK handshake on an IN transaction
may be corrupted, so the device may not receive the ACK for data
stage, the complete irq will not occur at this situation.
Therefore, we need to move prime status stage from complete irq
routine to the place where the data stage has just primed, or the
host will never get ACK for status stage.
The above issue has been described at USB2.0 spec chapter 8.5.3.3.

- After adding prime status stage just after prime the data stage,
there is a potential problem when the status dTD is added before the data stage
has primed by hardware. The reason is the device's dTD descriptor has NO direction bit,
if data stage (IN) prime hasn't finished, the status stage(OUT)
dTD will be added at data stage dTD's Next dTD Pointer, so when the data stage
transfer has finished, the status dTD will be primed as IN by hardware,
then the host will never receive ACK from the device side for status stage.

- Delete below code at fsl_ep_queue:
       /* Update ep0 state */
       if ((ep_index(ep) == 0))
               udc->ep0_state = DATA_STATE_XMIT;
the udc->ep0_state will be updated again after udc->driver->setup
finishes.

It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When runtime_pm was originally added, it was done in rather confusing
way: omap2430_musb_init() (called from musb_init_controller) would do
runtime_pm_get_sync() and musb_init_controller() itself would do
runtime_pm_put to balance it out. This is not only confusing but also
wrong if non-omap2430 glue layer is used.

This confusion resulted in commit 772aed45 "usb: musb: fix
pm_runtime mismatch", that removed runtime_pm_put() from
musb_init_controller as that looked unbalanced, and also happened to
fix unrelated isp1704_charger crash. However this broke runtime PM
functionality (musb is now always powered, even without gadget active).

Avoid these confusing runtime pm dependences by making
musb_init_controller() and omap2430_musb_init() do their own runtime
get/put pairs; also cover error paths. Remove unneeded runtime_pm_put
in omap2430_remove too. isp1704_charger crash that motivated
772aed45 will be fixed by following patch.

Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This change prevents runtime suspend and resume actual execution, if
omap2430 controller driver is loaded after musb-hdrc, and therefore the
controller isn't initialized properly.

The problem is reproducible with 3.1.y and 3.2 kernels.

Kernel configuration of musb:

  % cat .config | egrep 'MUSB|GADGET'
  CONFIG_USB_MUSB_HDRC=y
  # CONFIG_USB_MUSB_TUSB6010 is not set
  CONFIG_USB_MUSB_OMAP2PLUS=m
  # CONFIG_USB_MUSB_AM35X is not set
  CONFIG_MUSB_PIO_ONLY=y
  CONFIG_USB_GADGET=y
  # CONFIG_USB_GADGET_DEBUG is not set
  # CONFIG_USB_GADGET_DEBUG_FILES is not set
  # CONFIG_USB_GADGET_DEBUG_FS is not set
  CONFIG_USB_GADGET_VBUS_DRAW=2
  CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2
  CONFIG_USB_GADGET_MUSB_HDRC=m
  CONFIG_USB_GADGET_DUALSPEED=y
  CONFIG_USB_GADGETFS=m
  # CONFIG_USB_MIDI_GADGET is not set

Fixes the following oops on module unloading:

  Unable to handle kernel NULL pointer dereference at virtual address 00000220
  ----8<----
  [<bf162088>] (omap2430_runtime_resume+0x24/0x54 [omap2430]) from [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50)
  [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50) from [<c0031a24>] (_od_runtime_resume+0x28/0x2c)
  [<c0031a24>] (_od_runtime_resume+0x28/0x2c) from [<c0306cb0>] (__rpm_callback+0x60/0xa0)
  [<c0306cb0>] (__rpm_callback+0x60/0xa0) from [<c0307f2c>] (rpm_resume+0x3fc/0x6e4)
  [<c0307f2c>] (rpm_resume+0x3fc/0x6e4) from [<c030851c>] (__pm_runtime_resume+0x5c/0x90)
  [<c030851c>] (__pm_runtime_resume+0x5c/0x90) from [<c02fd0dc>] (__device_release_driver+0x2c/0xd0)
  [<c02fd0dc>] (__device_release_driver+0x2c/0xd0) from [<c02fda18>] (driver_detach+0xe8/0xf4)
  [<c02fda18>] (driver_detach+0xe8/0xf4) from [<c02fcf88>] (bus_remove_driver+0xa0/0x104)
  [<c02fcf88>] (bus_remove_driver+0xa0/0x104) from [<c02fde54>] (driver_unregister+0x60/0x80)
  [<c02fde54>] (driver_unregister+0x60/0x80) from [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20)
  [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20) from [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430])
  [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430]) from [<c007d8bc>] (sys_delete_module+0x1f4/0x264)
  [<c007d8bc>] (sys_delete_module+0x1f4/0x264) from [<c000f000>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: NVladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 3.1
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.

Cc: stable@vger.kernel.org
Signed-off-by: NGerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.

On such case we were not increment r->actual as we should.

This patch fixes that mistake.

Cc: stable@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.

Cc: stable@vger.kernel.org
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NPartha Basak <p-basak2@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we want to do device-initiated disconnect,
let's make sure we stop the UDC in order to
e.g. allow lower power states to be achieved by
turning off unnecessary clocks and/or stoping
PHYs.

When reconnecting, call ->udc_start() again to
make sure UDC is reinitialized.

Cc: stable@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Compilation error in case of non-DT configuration without this
of.h header file.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

Change number of ports to 3 for newer SoCs. Modify pdata structure
and ohci-at91 code that was dealing with ports information and check
of port indexes.
Several coding style errors have been addresses as the patch was touching
affected lines of code and was producing errors while run through
checkpatch.pl.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

The DT information are filled in a pdata structure and then passed on
to the usual check code of the probe function. Thus we do not need to
redo the gpio checking and irq configuration in the DT-related code.
On the other hand, we setup GPIO direction in driver for vbus and
overcurrent. It will be useful when moving to pinctrl subsystem.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

The information is not properly taken into account
for {get|set}_power() functions.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>		[3.2+]

Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.

There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Now skb_add_rx_frag() has a truesize parameter, we can fix f_phonet to
properly account truesize of each fragment : a full page.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_add_rx_frag() API is misleading.

Network skbs built with this helper can use uncharged kernel memory and
eventually stress/crash machine in OOM.

Add a 'truesize' parameter and then fix drivers in followup patches.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These interfaces need to be handled by QMI/WWAN driver
Signed-off-by: NAndrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the .reset method to the HCD, and update the .start method
accordingly for this change.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add OHCI shutdown methods to cleanly shutdown the OHCI controller on
system shutdowns and reboots.  This avoids the controller continuing
to run should be soft-reboot the platform, potentially scribbling
over system memory.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Combine usb_hcd_sa1111_probe() and ohci_hcd_sa1111_drv_probe(), doing
the same for the remove methods.

Move sa1111_start_hc and sa1111_stop_hc to be located next to these
the probe/release functions, as they're only called from them.

Get rid of the /*----*/ breaker lines.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use dev_dbg() instead, it's more friendly.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Clean up the ohci-sa1111 driver formatting to be more compliant with
current standards, and add 'static' to various function definitions
to avoid sparse complaints about undeclared functions.  Remove the
unnecessary local declaration of 'usb_disabled', which can be found
instead in linux/usb.h.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the USB interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

really weirdly spelled "while the list is non-empty, pick its
first element, remove it from the list and free it" kind of loop...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

can check MS_KERNMOUNT in flags now
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This device presents a total of 5 interfaces with ff/ff/ff
class/subclass/protocol. The last one of these is verified
to be a QMI/wwan combined interface which should be handled
by the qmi_wwan driver, so we blacklist it here.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

lock debugging already supports this, no need to do it explicitely.

Cc: balbi@ti.com
Cc: gregkh@linuxfoundation.org
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0d905fd5 "USB: option: convert Huawei K3765, K4505, K4605
reservered interface to blacklist" accidentally ANDed two
blacklist tests by leaving out a return.  This was not noticed
because the two consecutive bracketless if statements made it
syntactically correct.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds clk_prepare/clk_unprepare calls to the ohci-pxa27x
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ath79 usb driver doesn't do anything special and is now converted
to the generic ehci and ohci driver.
This was tested on a TP-Link TL-WR1043ND (AR9132)
Acked-by: NGabor Juhos <juhosg@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
CC: linux-mips@linux-mips.org
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a generic driver for platform devices. It works like the PCI
driver and is based on it. This is for devices which do not have an own
bus but their EHCI controller works like a PCI controller. It will be
used for the Broadcom bcma and ssb USB EHCI controller.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a generic driver for platform devices. It works like the PCI
driver and is based on it. This is for devices which do not have an own
bus but their OHCI controller works like a PCI controller. It will be
used for the Broadcom bcma and ssb USB OHCI controller.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMichał Wróbel <michal.wrobel@flytronic.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow to compile it if AT91 is enable.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>