Signed-off-by: NMarco Porsch <marco.porsch@etit.tu-chemnitz.de>
[prefix with IEEE80211_]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The debug message has to be printed also for an Auth message with
auth_sequence != 1. This helps understanding whether the two Auth
messages are exchanged correctly or not.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It does not make sense to keep a station alive if it is not authorised
at all. If IBSS/RSN is used it could also be the case that something
went wrong during the keys exchange and the stations ended up in a not
recoverable state.

By not updating last_rx we are giving the station a chance to be
deleted and to start the key exchange once again from scratch.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, mac80211 checks the DS params IE if present and
uses it for the (primary) BSS channel, instead of the one
that the frame was received on. This is particularly useful
in the 2.4 GHz band since a frame is often received on one
of the adjacent channels due to overlap.

Move this code to cfg80211 so other drivers also do this.

Additionally, on 5 GHz, in particular with some (possibly)
upcoming changes in 802.11ai and duplicate transmissions
when wider channels are used, something similar happens.
So if present, also use the (primary) channel information
contained in the HT operation IE.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the AP doesn't support HT, or more importantly if
it does but we have to disable it because its IEs are
broken, don't advertise HT support in our association
request. Otherwise, we configure our channel to be a
20 MHz non-HT channel but the AP might still think we
support HT, or even 40 MHz.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the 11n spec amendment was rolled into the
2012 version, "11n" no longer makes sense. Use
"HT" instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.

Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.

This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.

The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The radiotap vendor area in the skb head must be skipped
and accounted for in a few functions until it is removed.
I missed this in my patch, so a few places use this data
as though it was the 802.11 header, fix these places.
Reported-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Provide drivers with hooks to create debugfs files when
a new station is added. This would help drivers to take
advantage of mac80211's station list infrastructure and not maintain
tedious station management code internally.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
[ifdef inline wrapper functions]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sujith reported warnings with suspend/resume due to
channel contexts. When I looked into it, I realised
that the code was completely broken as it unassigned
the channel contexts when suspending, which actually
means they are destroyed.

Eliad Peller then pointed out that we also need to
remove the channel contexts from the driver. When I
looked into this, I also noticed that the code isn't
handling the virtual monitor interface correctly (if
it exists.)

Fix this by calling just the driver methods (if they
are implemented) instead of using the channel context
management code. Also add reconfiguration for the
virtual monitor interface.
Reported-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).

Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.
Signed-off-by: NEliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In some cases, in particular for experimentation, it
can be useful to be able to add vendor namespace data
to received frames in addition to the normal radiotap
data.

Allow doing this through mac80211 by adding fields to
the RX status descriptor that describe the data while
the data itself is prepended to the frame.

Also add some example code to hwsim, but don't enable
it because it doesn't use a proper OUI identifier.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Introduce IEEE80211_NUM_TIDS in the generic 802.11
header file and use it in place of STA_TID_NUM and
NUM_RX_DATA_QUEUES which are both really the number
of TIDs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of hardcoding its value (6), use the constant.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During testing our mac80211 driver a fatal error occurred which was
signalled to mac80211. Upon performing the reconfiguration of the
device a WARN_ON was triggered. This warning checked the return value
of drv_add_chanctx(). However, this returns -EOPNOTSUPP when the
driver does not provide the callback. As the callback is optional
better check it is defined before calling drv_add_chanctx().
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since channel contexts are usually present before
stations can be added to an interface, reassign
before stations them in reconfiguration as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.

Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clearly the tracepoint drv_offchannel_tx was
forgotten when that functionality was removed,
remove it now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a debugfs file showing which HW queues were
allocated to a virtual interface, including the
CAB queue for AP interfaces.

Change-Id: I486924e961b6ad6785a79db09620919ee644e703
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

One error path in ieee80211_subif_start_xmit() will
double-free the SKB. Set it to NULL to prevent that.

This issue was introduced by my channel context
changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is needed since this file exports functions.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If kstrtoull() returns an error code (a value
smaller than zero), use it since it can be an
error other than -EINVAL.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Accessing sdata->vif.bss_conf.bssid without any
protection here is racy, use u.mgd.associated
instead and lock the correct mutex for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of implementing practically the same
function (hwaddr_aton) use mac_pton.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The commit:

commit 5e760230
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Nov 4 11:18:17 2011 +0100

    cfg80211: allow registering to beacons

allowed only a single process to register for beacon events
per wiphy.  This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.

This patch allows multiple beacon listeners, fixing the
regression.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This new callback can be used to tune the rate to be used to send
multicast frames.

In the current state the multicast rate can be specified on IBSS/MESH
joining only. This makes it impossible to select a custom multicast
rate when then join command is sent by an external program (e.g.
wpa_supplicant)
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When userspace asks to deauthenticate and we're just
authenticated (or still authenticating) send a deauth
frame instead of deleting the auth request.

On the other hand, if we've just disassociated and
therefore deleted all our state already, drop the
deauth request because we no longer have a channel
context to send it on.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The TX status reporting is done for both the
nl80211 report as well as the socket option.
The socket option is also reported when an
skb is dropped to guarantee that the copy in
the IDR tree is freed and status is reported
to userspace.

However, when a frame is dropped, no nl80211
status is reported. This can cause userspace
to stop making progress while waiting for a
status notification.

Combine the nl80211 and socket option status
reporting into a new function and call it in
both places -- when the status comes in from
the driver and when the skb is dropped.

While at it, also simplify the code in the
nl80211 portion a bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.

Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.

Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code to allow EAPOL frames even when the station
isn't yet marked associated needs to check that the
incoming frame is long enough and due to paged RX it
also can't assume skb->data contains the right data,
it must use skb_copy_bits(). Fix this to avoid using
data that doesn't really exist.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.

To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to pskb_may_pull() checking the skb length, all
non-management frames are checked on input whether
their 802.11 header is fully present. Also add that
check for management frames and remove a check that
is now duplicate. This prevents accessing skb data
beyond the frame end.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The 'ssid' field of the cfg80211_ibss_params is a u8 pointer and
its length is likely to be less than IEEE80211_MAX_SSID_LEN most
of the time.

This patch fixes the ssid copy in ieee80211_ibss_join() by using
the SSID length to prevent it from reading beyond the string.

Cc: stable@vger.kernel.org
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
[rewrapped commit message, small rewording]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>