The SA controller spins down RAID drive spares.

A REGNEWD event causes an inquiry to be sent to all physical
drives. This causes the SA controller to spin up the spare.

The controller suspends all I/O to a logical volume until
the spare is spun up. The spin-up can take over 50 seconds.

This can result in one or both of the following:
 - SML sends down aborts and resets to the logical volume
   and can cause the logical volume to be off-lined.
 - a negative impact on the logical volume's I/O performance
   each time a REGNEWD is triggered.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The device ID obtained from the inquiry can only be of a single type.
The original code places a check for TYPE_ZBC right after the check for
TYPE_DISK. Logically, if the first if statement sees a device of a
TYPE_DISK and moves on to the second statement checking if not TYPE_ZBC,
it will always hit the continue.

[mkp: Applied by hand]
Signed-off-by: NPetros Koutoupis <petros@petroskoutoupis.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NGerry Morong <gerry.morong@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Need to report HBA device removal faster than the
event handler polling interval.

Stop I/O to the removed disk and wait for all
I/O operations to flush before removing the device.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

set offload_to_be_enabled to 0 when an ioaccel2 error is processed.

Before, an ioaccel completion error would turn of ioaccel but a rescan
would turn it back on again.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

offload_to_be_enabled also needs to be set to 0 during a state
change.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

faulty drives can cause the driver to hang during a
scan operation.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There have been companies requesting a sysfs entry
to obtain the sas address of device.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver was calling scsi_scan_host before enabling interrupts.

This has gone unnoticed except for customers running in intx mode.
Calling scsi_scan_host before interrupts are enabled causes
"irq XX: nobody cared" messages and the driver to hang.

This patch enables interrupts before the call to scsi_scan_host.
Reported-by: NPiotr Karbowski <piotr.karbowski@gmail.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This has only called from show_sas_rphy_enclosure_identifier().  The
caller expects that we set an identifier, otherwise it uses an
uninitialized variable.

[mkp: fixed typo]
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch depends on patch
 - commit ac10a3e4ed64
   ("Export function scsi_scan.c:sanitize_inquiry_string")
Suggested-by: NHannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs mrochs@linux.vnet.ibm.com
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An oops can occur when submitting ioaccel2 commands when the phys_disk
pointer is NULL in hpsa_scsi_ioaccel_raid_map.  Happens when there are
configuration changes during I/O operations.

If the phys_disk pointer is NULL, send the command down the RAID path.
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Aborts were not being sent down to HBA devices
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Stop annoying "Error, could not get enclosure information"
messages.
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Adding a new method to display enclosure device information.
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Left off some changes from Rasmus Villemoes where he changed snprintf to
scnprintf.
Suggested-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

HPSA_DIAG_OPTS_DISABLE_RLD_CACHING is a mask and bitwise AND was
intended here instead of logical &&.  This bug is essentially harmless,
it means that sometimes we don't print a warning message which we wanted
to print.

Fixes: c2adae44 ('hpsa: disable report lun data caching')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags.  We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJens Axboe <axboe@kernel.dk>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This patch fixes a 'general protection fault' issue by
moving the attribute to where it was likely meant.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Gerry Morong <gerry.morong.pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

path_info_show() seems to be broken in multiple ways.

First, there's

  817 return snprintf(buf, output_len+1, "%s%s%s%s%s%s%s%s",
  818       path[0], path[1], path[2], path[3],
  819       path[4], path[5], path[6], path[7]);

so hopefully output_len contains the combined length of the eight
strings. Otherwise, snprintf will stop copying to the output
buffer, but still end up reporting that combined length - which
in turn would result in user-space getting a bunch of useless nul
bytes (thankfully the upper sysfs layer seems to clear the output
buffer before passing it to the various ->show routines). But we have

  767      output_len = snprintf(path[i],
  768                       PATH_STRING_LEN, "[%d:%d:%d:%d] %20.20s ",
  769                       h->scsi_host->host_no,
  770                       hdev->bus, hdev->target, hdev->lun,
  771                       scsi_device_type(hdev->devtype));

so output_len at best contains the length of the last string printed.

Inside the loop, we then otherwise add to output_len. By magic,
we still have PATH_STRING_LEN available every time... This
wouldn't really be a problem if the bean-counting has been done
properly and each line actually does fit in 50 bytes, and maybe
it does, but I don't immediately see why. Suppose we end up
taking this branch:

  802                  output_len += snprintf(path[i] + output_len,
  803                          PATH_STRING_LEN,
  804                          "BOX: %hhu BAY: %hhu %s\n",
  805                          box, bay, active);

An optimistic estimate says this uses strlen("BOX: 1 BAY: 2
Active\n") which is 21. Now add the 20 bytes guaranteed by the
%20.20s and then some for the rest of that format string, and
we're easily over 50 bytes. I don't think we can get over 100
bytes even being pessimistic, so this just means we'll scribble
into the next path[i+1] and maybe get that overwritten later,
leading to some garbled output (in fact, since we'd overwrite the
previous string's 0-terminator, we could end up with one very
long string and then print various suffixes of that, leading to
much more than 400 bytes of output). Except of course when we're
filling path[7], where overrunning it means writing random stuff
to the kernel stack, which is usually a lot of fun.

We can fix all of that and get rid of the 400 byte stack buffer by
simply writing directly to the given output buffer, which the upper
layer guarantees is at least PAGE_SIZE. s[c]nprintf doesn't care where
it is writing to, so this doesn't make the spin lock hold time any
longer. Using scnprintf ensures that output_len always represents the
number of bytes actually written to the buffer, so we'll report the
proper amount to the upper layer.
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When external target arrays are present, disable the firmware's
normal behavior of returning a cached copy of the report lun data,
and force it to collect new data each time we request a report luns.

This is necessary for external arrays, since there may be no
reliable signal from the external array to the smart array when
lun configuration changes, and thus when driver requests
report luns, it may be stale data.

Use diag options to turn off RPL data caching.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are problems with getting configuration change notification
in pass-through RAID environments.  So, activate flag
h->discovery_polling when one of these devices is detected in
update_scsi_devices.

After discovery_polling is set, execute a report luns from
rescan_controller_worker (every 30 seconds).

If the data from report_luns is different than last
time (binary compare), execute a full rescan via update_scsi_devices.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We don't need to create fake enclosure devices at Lun0
in external target array configurations anymore.
This was done to support Pre-SCSI rev 5 controllers
that didn't suppoprt report luns commands, so the
SCSI layer had to scan targets. If there was no
LUN at LUN 0, then the target scan would stop, and
move to the next target.  Lun0 enclosure device
was added to prevent sparsely-numbered LUNs from
being missed.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

External array LUNs must use target and lun numbers assigned by the
external array. So the driver must treat these differently from
local LUNs when assigning lun/target.

LUN's 'model' field has been used to detect Lun types that need
special treatment, but the desire is to eliminate the need to reference
specific array models, and support any external array.

Pass-through RAID (PTRAID) luns are not luns of the local controller,
so they are not reported in LUN count of command 'ID controller'.
However, they ARE reported in "Report logical Luns" command.
Local luns are listed first, then PTRAID LUNs.

The number of luns from "Report LUNs" in excess of those reported by
'ID controller' are therefore the PTRAID LUNS.

We can now remove function is_ext_target, and the 'white list'
array of supported model names.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

preparation for adding the sas transport class
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

setup for sas transport. Need to set the
bus and target accordingly.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

use an index into vpd data for SAS/SATA drives
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

simplify checking for logical/physical devices
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

remove repeated calculation that checks for physical
or logical devices.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

remove macros and cleanup device exposure checking
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver is using two MACROs which seemingly are looking in
the wrong location for the device_flags returned from
CISS_REPORT_PHYS. Both MACROs, NON_DISK_PHYS_DEV and
PHYS_IOACCEL, are using the pointer returned from figure_lunaddrbytes
which is the address of the LUN.lunid element in
the extended CISS_REPORT_PHYS.  But the MACROS are using offsets
beyond the range of the element (offset 17 of an 8 byte element).

These MACROs actually are looking at the correct location but
they fail static checker analysis. It also will not work
if any new elements are added to the extended LUN structure.

Change the code to use the structure elements directly
since this MACRO is only used in one location.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set reset type in device_reset_handler to do either
logical unit reset for logical devices, or physical
target reset, for physical devices.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix a NULL pointer issue in the driver when devices are removed
during a reset.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

handle block counts of 0. Cleanup block and block count calculations.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>