Add kvm_release_page_clean() after is_error_page() to avoid
leakage of error page.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When using a relocatable kernel we need to make sure that the trampline code
and the interrupt handlers are both copied to low memory. The only way to do
this reliably is to put them in the copied section.

This patch should make relocated kernels work with KVM.

KVM-Stable-Tag
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On Book3S KVM we directly expose some asm pointers to C code as
variables. These need to be relocated and thus break on relocatable
kernels.

To make sure we can at least build, let's mark them as long instead
of u32 where 64bit relocations don't work.

This fixes the following build error:

WARNING: 2 bad relocations^M
> c000000000008590 R_PPC64_ADDR32    .text+0x4000000000008460^M
> c000000000008594 R_PPC64_ADDR32    .text+0x4000000000008598^M

Please keep in mind that actually using KVM on a relocated kernel
might still break. This only fixes the compile problem.
Reported-by: NSubrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Book3S_32 requires MSR_DR to be disabled during load_up_xxx while on Book3S_64
it's supposed to be enabled. I misread the code and disabled it in both cases,
potentially breaking the PS3 which has a really small RMA.

This patch makes KVM work on the PS3 again.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On Book3s_32 the tlbie instruction flushed effective addresses by the mask
0x0ffff000. This is pretty hard to reflect with a hash that hashes ~0xfff, so
to speed up that target we should also keep a special hash around for it.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On failure gfn_to_pfn returns bad_page so use correct function to check
for that.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

So far we've been running all code without locking of any sort. This wasn't
really an issue because I didn't see any parallel access to the shadow MMU
code coming.

But then I started to implement dirty bitmapping to MOL which has the video
code in its own thread, so suddenly we had the dirty bitmap code run in
parallel to the shadow mmu code. And with that came trouble.

So I went ahead and made the MMU modifying functions as parallelizable as
I could think of. I hope I didn't screw up too much RCU logic :-). If you
know your way around RCU and locking and what needs to be done when, please
take a look at this patch.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Due to previous changes, the Book3S_32 guest MMU code didn't compile properly
when enabling debugging.

This patch repairs the broken code paths, making it possible to define DEBUG_MMU
and friends again.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We need to tell the guest the opcodes that make up a hypercall through
interfaces that are controlled by userspace. So we need to add a call
for userspace to allow it to query those opcodes so it can pass them
on.

This is required because the hypercall opcodes can change based on
the hypervisor conditions. If we're running in hardware accelerated
hypervisor mode, a hypercall looks different from when we're running
without hardware acceleration.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On BookE the preferred way to write the EE bit is the wrteei instruction. It
already encodes the EE bit in the instruction.

So in order to get BookE some speedups as well, let's also PV'nize thati
instruction.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

There is also a form of mtmsr where all bits need to be addressed. While the
PPC64 Linux kernel behaves resonably well here, on PPC32 we do not have an
L=1 form. It does mtmsr even for simple things like only changing EE.

So we need to hook into that one as well and check for a mask of bits that we
deem safe to change from within guest context.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The PowerPC ISA has a special instruction for mtmsr that only changes the EE
and RI bits, namely the L=1 form.

Since that one is reasonably often occuring and simple to implement, let's
go with this first. Writing EE=0 is always just a store. Doing EE=1 also
requires us to check for pending interrupts and if necessary exit back to the
hypervisor.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When we hook an instruction we need to make sure we don't clobber any of
the registers at that point. So we write them out to scratch space in the
magic page. To make sure we don't fall into a race with another piece of
hooked code, we need to disable interrupts.

To make the later patches and code in general easier readable, let's introduce
a set of defines that save and restore r30, r31 and cr. Let's also define some
helpers to read the lower 32 bits of a 64 bit field on 32 bit systems.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We will need to patch several instruction streams over to a different
code path, so we need a way to patch a single instruction with a branch
somewhere else.

This patch adds a helper to facilitate this patching.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We will soon require more sophisticated methods to replace single instructions
with multiple instructions. We do that by branching to a memory region where we
write replacement code for the instruction to.

This region needs to be within 32 MB of the patched instruction though, because
that's the furthest we can jump with immediate branches.

So we keep 1MB of free space around in bss. After we're done initing we can just
tell the mm system that the unused pages are free, but until then we have enough
space to fit all our code in.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

With our current MMU scheme we don't need to know about the tlbsync instruction.
So we can just nop it out.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Some instructions can simply be replaced by load and store instructions to
or from the magic page.

This patch replaces often called instructions that fall into the above category.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We will soon start and replace instructions from the text section with
other, paravirtualized versions. To ease the readability of those patches
I split out the generic looping and magic page mapping code out.

This patch still only contains stubs. But at least it loops through the
text section :).
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We have all the hypervisor pieces in place now, but the guest parts are still
missing.

This patch implements basic awareness of KVM when running Linux as guest. It
doesn't do anything with it yet though.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Now that we have the shared page in place and the MMU code knows about
the magic page, we can expose that capability to the guest!
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We need to override EA as well as PA lookups for the magic page. When the guest
tells us to project it, the magic page overrides any guest mappings.

In order to reflect that, we need to hook into all the MMU layers of KVM to
force map the magic page if necessary.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We will be introducing a method to project the shared page in guest context.
As soon as we're talking about this coupling, the shared page is colled magic
page.

This patch introduces simple defines, so the follow-up patches are easier to
read.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On PowerPC it's very normal to not support all of the physical RAM in real mode.
To check if we're matching on the shared page or not, we need to know the limits
so we can restrain ourselves to that range.

So let's make it a define instead of open-coding it. And while at it, let's also
increase it.
Signed-off-by: NAlexander Graf <agraf@suse.de>

v2 -> v3:

  - RMO -> PAM (non-magic page)
Signed-off-by: NAvi Kivity <avi@redhat.com>

When the guest turns on interrupts again, it needs to know if we have an
interrupt pending for it. Because if so, it should rather get out of guest
context and get the interrupt.

So we introduce a new field in the shared page that we use to tell the guest
that there's a pending interrupt lying around.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

While running in hooked code we need to store register contents out because
we must not clobber any registers.

So let's add some fields to the shared page we can just happily write to.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When running in hooked code we need a way to disable interrupts without
clobbering any interrupts or exiting out to the hypervisor.

To achieve this, we have an additional critical field in the shared page. If
that field is equal to the r1 register of the guest, it tells the hypervisor
that we're in such a critical section and thus may not receive any interrupts.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

To communicate with KVM directly we need to plumb some sort of interface
between the guest and KVM. Usually those interfaces use hypercalls.

This hypercall implementation is described in the last patch of the series
in a special documentation file. Please read that for further information.

This patch implements stubs to handle KVM PPC hypercalls on the host and
guest side alike.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When in kernel mode there are 4 additional registers available that are
simple data storage. Instead of exiting to the hypervisor to read and
write those, we can just share them with the guest using the page.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.

Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DSISR register contains information about a data page fault. It is fully
read/write from inside the guest context and we don't need to worry about
interacting based on writes of this register.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.

So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.

This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Since powerpc uses -Werror on arch powerpc, the build was broken like
this:

  cc1: warnings being treated as errors
  arch/powerpc/kernel/module.c: In function 'module_finalize':
  arch/powerpc/kernel/module.c:66: error: unused variable 'err'
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With all the recent module loading cleanups, we've minimized the code
that sits under module_mutex, fixing various deadlocks and making it
possible to do most of the module loading in parallel.

However, that whole conversion totally missed the rather obscure code
that adds a new module to the list for BUG() handling.  That code was
doubly obscure because (a) the code itself lives in lib/bugs.c (for
dubious reasons) and (b) it gets called from the architecture-specific
"module_finalize()" rather than from generic code.

Calling it from arch-specific code makes no sense what-so-ever to begin
with, and is now actively wrong since that code isn't protected by the
module loading lock any more.

So this commit moves the "module_bug_{finalize,cleanup}()" calls away
from the arch-specific code, and into the generic code - and in the
process protects it with the module_mutex so that the list operations
are now safe.

Future fixups:
 - move the module list handling code into kernel/module.c where it
   belongs.
 - get rid of 'module_bug_list' and just use the regular list of modules
   (called 'modules' - imagine that) that we already create and maintain
   for other reasons.
Reported-and-tested-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sigreturn zero regs->trap, make do_signal() do the same on all
paths.  As it is, signal interrupting e.g. read() from fd 512 (==
ERESTARTSYS) with another signal getting unblocked when the first
handler finishes will lead to restart one insn earlier than it ought
to.  Same for multiple signals with in-kernel handlers interrupting
that sucker at the same time.  Same for multiple signals of any kind
interrupting that sucker on 64bit...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area.  A missing call could
introduce problems on some architectures.

This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.

This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures.  This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: NBen Hawkes <hawkes@sota.gen.nz>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NChris Metcalf <cmetcalf@tilera.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NTony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>

The slab.h header is required to use the kmalloc() family of functions.
Due to recent kernel changes, this header must be directly included by
code that calls into the memory allocator.

Without this patch, any code which includes this header fails to build.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tighten up time timing around the gpio reset functionality.  Add a 200ns
delay before remuxing the pins back to ac97 to comply with the ac97 spec.
Signed-off-by: NEric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This function is implemented as though the function of_get_next_child does
not increment the reference count of its result, but actually it does.
Thus the patch adds of_node_put in error handling code and drops a call to
of_node_get.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
local idexpression x;
expression E1;
position p1,p2;
@@

x@p1 = of_get_next_child(...);
... when != x = E1
of_node_get@p2(x)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

cocci.print_main("call",p1)
cocci.print_secs("get",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>