on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.

This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is to avoid the usual two or three messages about the command
timing out.  We're obviously not waiting long enough.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is to ensure the board interrupts are really off when
these functions return.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Apparently we've been doin it rong for a decade, but only lately do we
run into problems.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

It's not enough to simple avoid putting the board into performant
mode, as we have to set up the interrupts differently, etc.  When
I originally tested this module parameter, I tested it incorrectly
without realizing it, and the driver was running in performant mode
the whole time unbeknownst to me.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Driver's internal queues should be FIFO, not LIFO.
This is a port of an almost identical patch from cciss by Jens Axboe.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers.  Also, only wait 10 secs
for board to become "not ready" after a reset (it should quickly
become not ready.)
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The firmware may have been updated, in which case, it's the same device,
and in that case, we do not want to remove and add the device, we want to
let it continue as is.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This uses the scatter-gather chaining feature of Smart Array
controllers.  32 scatter-gather elements are embedded in the
"command list", and the last element in the list may be marked
as a "chain pointer", and point to an additional block of
scatter gather elements.  The precise number of scatter gather
elements supported is dependent on the particular kind of
Smart Array, and is determined at runtime by querying the
hardware.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The intent of the scan thread was to allow a UNIT ATTENTION/LUN
DATA CHANGED condition encountered in the interrupt handler
to trigger a rescan of devices, which can't be done in interrupt
context.  However, we weren't able to get this to work, due to
multiple such UNIT ATTENTION conditions arriving during the rescan,
during updating of the SCSI mid layer, etc.  There's no way to tell
the devices, "stand still while I scan you!"  Since it doesn't work,
there's no point in having the thread, as the rescan triggered via
ioctl or sysfs can be done without such a thread.
Signed-off-by: NMike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

use scan_start and scan_finished entry points for scanning and route
the CCISS_REGNEWD ioctl and sysfs triggering of same functionality
through hpsa_scan_start.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The p1210m responsds to SCSI report LUNs, unlike traditional Smart
Array controllers.  This means that the bus, target, and lun
assignments done by the driver cannot be arbitrary, but must match
what SCSI REPORT LUNS returns.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is done by adding support for the so-called "performant mode"
(that's really what they called it).  Smart Array controllers
have a mode which enables multiple command completions to be
delivered with a single interrupt, "performant" mode.  We want to use
that mode, as some newer controllers will be requiring this mode.
Signed-off-by: NDon Brace <brace@beardog.cce.hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NMike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

That is, use u64, u32, u16 and u8 rather than __u64, __u32, __u16 and __u8.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This driver supports a subset of HP Smart Array Controllers.
It is a SCSI alternative to the cciss driver.

[akpm@linux-foundation.org: avoid helpful cleanup patches]
[achiang@hp.com: make device attrs static]
[akpm@linux-foundation.org: msleep() does set_current_state() itself]
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NMike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>