Signed-off-by: NEric Miao <eric.miao@canonical.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The NAND support is implemented through the gen_nand driver.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Add supported for PCF8574A GPIO expander and LEDs attached to it.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This driver adds support for the on-board CF socket.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This huge patch mostly shuffles code. The spitz.c file contained terrible mess
and needed a cleanup, here it is:

1) Made every part modular, components are not built in if not selected.
2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA .... #endif" and
   similar code. The kernel size will grow by a few kb now, but the file is much
   more readable.
3) Reworked SD/CF power setting function and made it reentrant.
4) Add ISL6271A regulator support
5) Correctly register WM8750
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This contains common code for Palm LD, TX, T5, Z72, Treo680, Centro
This code also adds PMIC support for all the devices,
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Only a small part of used code is moved into sharpsl_pm.h.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

ARCH_GUMSTIX_ORIG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Acked-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Since we no longer support discontigmem, node is always zero, so
remove this argument.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is support for custom design based on Toradex Colibri PXA270 CPU card.
Initial patch was by Pavel Revak.

[daniel - rebased the code to follow the module/board split]
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Pavel Revak <palo@bielyvlk.sk>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Follow the idea of several MX31 based boards and split code that is
related to the module from code that is baseboard specific. This makes
adding new base board support easier, while avoiding code duplication.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch just moves code around and polishes it. Also, compile in only
selected pieces of hardware.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.

The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMarc Zyngier <maz@misterjones.org>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NDaniel Mack <daniel@caiaq.de>

The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Reviewed-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

PCMCIA support for Voipac PXA270
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful.  Move
it to mach/Kconfig.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

No need to separate them as they should be together from the begining.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented
them being used simultaneously when supporting multiple PXA SoCs, esp.
in drivers/spi/pxa2xx_spi.c, make them correct.

The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result
a little bit different in pxa2xx_spi_probe(), however, since that's only
used as a default initialization value, it's acceptable.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated
and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant
function declarations and data structures.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>

The use of mfp_cfg_t causes build errors without including <mach/mfp.h>.

CC: stable@kernel.org
CC: Daniel Mack <daniel@caiaq.de>
Signed-off-by: NJakob Viketoft <jakob.viketoft@bitsim.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Fix the wrong variable used in cpu_is_pxa950().
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Due to commit:

    5de813b6  ARM: Eliminate decompressor -Dstatic= PIC hack

The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This converts arm to the generic pci_set_dma_mask and
pci_set_consistent_dma_mask (removes HAVE_ARCH_PCI_SET_DMA_MASK for
dmabounce).
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Looked-over-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>