When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880

Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.

ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata7.00: BMDMA2 stat 0x50001
ata7.00: failed command: DATA SET MANAGEMENT
ata7.00: cmd 06/01:01:00:00:00/00:00:00:00:00/a0 tag 0 dma 512 out
         res 51/04:01:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
ata7.00: status: { DRDY ERR }
ata7.00: error: { ABRT }
ata7.00: device reported invalid CHS sector 0
sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 8:0:0:0: [sdb] tag#0 Sense Key : Illegal Request [current] [descriptor]
sd 8:0:0:0: [sdb] tag#0 Add. Sense: Unaligned write command
sd 8:0:0:0: [sdb] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 21 95 88 00 20 00 00 00 00
blk_update_request: I/O error, dev sdb, sector 2200968
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NTejun Heo <tj@kernel.org>

Replace occurences of the pci api by appropriate call to the dma api.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr)

@deprecated@
idexpression id;
position p;
@@

(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@bad1@
idexpression id;
position deprecated.p;
@@
...when != &id->dev
   when != pci_get_drvdata ( id )
   when != pci_enable_device ( id )
(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@depends on !bad1@
idexpression id;
expression direction;
position deprecated.p;
@@

(
- pci_dma_supported@p ( id,
+ dma_supported ( &id->dev,
...
+ , GFP_ATOMIC
  )
|
- pci_alloc_consistent@p ( id,
+ dma_alloc_coherent ( &id->dev,
...
+ , GFP_ATOMIC
  )
)
Signed-off-by: NQuentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable.  Benefits of this change:

* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
  and CONFIG_PM_RUNTIME=y configurations

* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
  the future

* more consistent code (there are host drivers which are using the correct
  CONFIG_PM_SLEEP checks already)

The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Cc: linux-ide@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

It's a bit odd to see a newer device showing mod15write; however, the
reported behavior is highly consistent and other factors which could
contribute seem to have been verified well enough.  Also, both
sata_sil itself and the drive are fairly outdated at this point making
the risk of this change fairly low.  It is possible, probably likely,
that other drive models in the same family have the same problem;
however, for now, let's just add the specific model which was tested.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: Nmatson <lists-matsonpa@luxsci.me>
References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com
Cc: stable@vger.kernel.org

Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev.  This is a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Jeff moved on to a greener pasture.

 s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>

This patch converts the drivers in drivers/ata/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Mark Lord <kernel@teksavvy.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Init 'serror' to silence the following warning:

drivers/ata/sata_sil.c: In function ‘sil_interrupt’:
drivers/ata/sata_sil.c:453:14: warning: ‘serror’ may be used uninitialized in
this function [-Wuninitialized]

This is not a 'can never happen' but is nonetheless extremely unlikely.
The easiest and cleanest warning fix is simply to init the var,
rather than worry about marking the var uninit-ok.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use a single mechanism to show driver version.
Reduces text a tiny bit too.

Remove uses of static int printed_version
Add and use ata_print_version(const struct device *, const char *ver)
and ata_print_version_once.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 543870	  73893	 116592	 734355	  b34ad	drivers/ata/built-in.allyesconfig.print_once.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 141212	  14689	   4220	 160121	  27179	drivers/ata/built-in.defconfig.print_once.o
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Saves text by removing nearly duplicated text format strings by
creating ata_<foo>_printk functions and printf extension %pV.

ata defconfig size shrinks ~5% (~8KB), allyesconfig ~2.5% (~13KB)

Format string duplication comes from:

 #define ata_link_printk(link, lv, fmt, args...) do { \
       if (sata_pmp_attached((link)->ap) || (link)->ap->slave_link)    \
               printk("%sata%u.%02u: "fmt, lv, (link)->ap->print_id,   \
                      (link)->pmp , ##args); \
       else \
               printk("%sata%u: "fmt, lv, (link)->ap->print_id , ##args); \
       } while(0)

Coalesce long formats.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.allyesconfig.dev_level.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.defconfig.dev_level.o
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Saves a bit of text as the call takes fewer args.

Coalesce a few formats.
Convert a few bare printks to pr_cont.

$ size drivers/ata/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.o.allyesconfig.new
 559574	  73893	 117888	 751355	  b76fb	drivers/ata/built-in.o.allyesconfig.old
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.o.defconfig.new
 149851	  14689	   4220	 168760	  29338	drivers/ata/built-in.o.defconfig.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c306 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efd (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 0d5ff566 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_sff_irq_clear() is BMDMA specific.  Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.

Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
      possibly by sata_sil.  This should be moved to respective low
      level drivers later.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

struct ata_prd and ap->prd are BMDMA specific.  Add bmdma_ prefix to
them and move them inside CONFIG_ATA_SFF.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken.  Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.

Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead.  ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.

This simplifies condition check in IRQ handlers.  While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We must disable the DMA engine before accessing taskfile registers.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

host->ports[] always contain pointers to valid port structures since
a "dummy port" structure is used in case if there is no physical port.

This patch takes care of two entries from Dan's list:

drivers/ata/sata_sil.c +535 sil_interrupt(13) warning: variable derefenced before check 'ap'
drivers/ata/sata_mv.c +2517 mv_unexpected_intr(6) warning: variable derefenced before check 'ap'

and of another needless NULL pointer check in pata_octeon_cf.c.
Reported-by: NDan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

32-bit PIO seems to work fine on sata_sil hardware (tested on SiI3114) and is
listed as OK in the Silicon Image datasheets. Enable it.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

No functional changes in this patch.
Signed-off-by: NErik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:

  CC [M]  drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2

include/linux/libata.h has the following enabled:

#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP

This fixes the compilation.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit e57db7bd (SATA Sil: Blacklist system that spins off disks during ACPI power off)
 breaks build like the following, in both cases when CONFIG_DMI set or not.

        drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
        drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
        drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast

  sata_sil.c should include dmi.h
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6325 that uses the sata_sil driver.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This implements support for the Large Block Transfer feature found in Silicon
Image 311x controllers. This allows transferring bigger contiguous chunks of
data from system memory and avoids the 64KB boundary restriction of standard
SFF controllers.

This is based on a patch from Jeff Garzik (from the sii-lbt branch of
libata-dev) but includes a few bug fixes: Since the bmdma2 register does not
implement the status bits, the original bmdma register must be used except
where the bmdma2 register is required. As well the DMA boundary should be
31-bit instead of 32-bit since the top bit of the length field is still
required for the PRD end-of-table flag.
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There currently are the following looping constructs.

* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order

Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link.  Instead of adding another one with long name, do the following
cleanup.

* Implement and export ata_link_next() and ata_dev_next() which take
  @mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
  looping mode explicitly.

The following iteration modes are implemented.

* ATA_LITER_EDGE		: loop over edge links
* ATA_LITER_HOST_FIRST		: loop over all links, host link first
* ATA_LITER_PMP_FIRST		: loop over all links, PMP links first

* ATA_DITER_ENABLED		: loop over enabled devices
* ATA_DITER_ENABLED_REVERSE	: loop over enabled devices in reverse order
* ATA_DITER_ALL			: loop over all devices
* ATA_DITER_ALL_REVERSE		: loop over all devices in reverse order

This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link.  However, that assumption won't hold anymore with the scheduled
addition of slave link.

Make SCR access ops per-link.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: NTejun Heo <htejun@gmail.com>

SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: NTejun Heo <htejun@gmail.com>

ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions.  Kill it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata lets low level drivers build ata_port_operations table and
register it with libata core layer.  This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.

This becomes worse for drivers which support related similar
controllers which differ slightly.  They share most of the operations
except for a few.  However, the driver still needs to list all
operations for each variant.  This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.

This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone.  When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time.  Some of those inconsistencies
cause immediate problems and fixed.  Others just remain there dormant
making maintenance increasingly difficult.

To rectify the problem, this patch implements ata_port_operations
inheritance.  To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance.  An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop.  When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified.  This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.

libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma.  To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.

After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to.  The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.

* sata_sx4 is still using old style EH and currently doesn't take
  advantage of ops inheritance.
Signed-off-by: NTejun Heo <htejun@gmail.com>

libata lets low level drivers build scsi_host_template and register it
to the SCSI layer.  This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.

This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht.  Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.

All sht tables are identical before and after this patch.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies.  This patch updates drivers.

* Enable/disable_pm callbacks added to all ahci ops tables.

* Every driver for SFF controllers now uses ata_sff_port_start()
  instead of ata_port_start() unless the driver has custom
  implementation.

* Every driver for SFF controllers now uses ata_pci_default_filter()
  unless the driver has custom implementation.

* Removed an odd port_info->sht initialization from ata_piix.c.
  Likely a merge byproduct.

* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
  to ata_cable_sata().  Remove it from via and mv port ops.

* Some drivers had unnecessary .max_sectors initialization which is
  ignored and was missing .slave_destroy callback.  Fixed.

* Removed unnecessary sht initializations port_info's.

* Removed onsolete scsi device suspend/resume callbacks from
  pata_bf54x.

* No reason to set ata_pci_default_filter() and bmdma functions for
  PIO-only drivers.  Remove those callbacks and replace
  ata_bmdma_irq_clear with ata_noop_irq_clear.

* pata_platform sets port_start to ata_dummy_ret0.  port_start can
  just be set to NULL.

* sata_fsl supports NCQ but was missing qc_defer.  Fixed.

* pata_rb600_cf implements dummy port_start.  Removed.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Now that hardreset is the preferred method of resetting, there's no
need for ATA_LFLAG_HRST_TO_RESUME flag.  Kill it.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ.  It also should
be cleared after reset just like SError itself.

Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Interestingly, sata_sil raises spurious interrupts if it's coupled
with Sil SATA_PATA bridge.  Currently, sata_sil interrupt handler is
strict about spurious interrupts and freezes the port when it occurs.
This patch makes it more forgiving.

* On SATA PHY event interrupt, serror value is checked to see whether
  it really is PHYRDY CHG event.  If not, SATA PHY event interrupt is
  ignored.

* If ATA interrupt occurs while no command is in progress, it's
  cleared and ignored.

This fixes bugzilla bug 9505.

  http://bugzilla.kernel.org/show_bug.cgi?id=9505Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: NJeff Garzik <jeff@garzik.org>