First in rlb_teach_disabled_mac_on_primary() it's okay to remove
curr_slave_lock as all callers except bond_alb_monitor() already hold
RTNL, and in case bond_alb_monitor() is executing we can at most have a
period with bad throughput (very unlikely though).
In bond_alb_monitor() it's okay to remove the read_lock as the slave
list is walked with RCU and the worst that could happen is another
transmitter at the same time and thus for a period which currently is 10
seconds (bond_alb.h: BOND_ALB_LP_TICKS).
And bond_alb_handle_active_change() is okay because it's always called
with RTNL. Removed the ASSERT_RTNL() because it'll be inserted in the
parent function in a following patch.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the read_lock in bond_3ad_lacpdu_recv() since when the slave is
being released its rx_handler is removed before 3ad unbind, so even if
packets arrive, they won't see the slave in an inconsistent state.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

virtqueue_add() populates the virtqueue descriptor table from the sgs
given.  If it uses an indirect descriptor table, then it puts a single
descriptor in the descriptor table pointing to the kmalloc'ed indirect
table where the sg is populated.

Previously vring_add_indirect() did the allocation and the simple
linear layout.  We replace that with alloc_indirect() which allocates
the indirect table then chains it like the normal descriptor table so
we can reuse the core logic.

This slows down pktgen by less than 1/2 a percent (which uses direct
descriptors), as well as vring_bench, but it's far neater.

vring_bench before:
	1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
vring_bench after:
	1125610268-1183528965(1.14172e+09+/-8e+06)ns

pktgen before:
   787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0

pktgen after:
   779988-790404(786391+/-2.5e+03)pps 361-366(364.35+/-1.3)Mb/sec (361914432-366747456(3.64885e+08+/-1.2e+06)bps) errors: 0

Now, if we make force indirect descriptors by turning off any_header_sg
in virtio_net.c:

pktgen before:
  713773-721062(718374+/-2.1e+03)pps 331-334(332.95+/-0.92)Mb/sec (331190672-334572768(3.33325e+08+/-9.6e+05)bps) errors: 0
pktgen after:
  710542-719195(714898+/-2.4e+03)pps 329-333(331.15+/-1.1)Mb/sec (329691488-333706480(3.31713e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to have several callers which just used arrays.  They're
gone, so we can use sg_next() everywhere, simplifying the code.

On my laptop, this slowed down vring_bench by 15%:

vring_bench before:
	936153354-967745359(9.44739e+08+/-6.1e+06)ns
vring_bench after:
	1061485790-1104800648(1.08254e+09+/-6.6e+06)ns

However, a more realistic test using pktgen on a AMD FX(tm)-8320 saw
a few percent improvement:

pktgen before:
  767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0

pktgen after:
   787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the only driver which doesn't hand virtqueue_add_inbuf and
virtqueue_add_outbuf a well-formed, well-terminated sg.  Fix it,
so we can make virtio_add_* simpler.

pktgen results:
	modprobe pktgen
	echo 'add_device eth0' > /proc/net/pktgen/kpktgend_0
	echo nowait 1 > /proc/net/pktgen/eth0
	echo count 1000000 > /proc/net/pktgen/eth0
	echo clone_skb 100000 > /proc/net/pktgen/eth0
	echo dst_mac 4e:14:25:a9:30:ac > /proc/net/pktgen/eth0
	echo dst 192.168.1.2 > /proc/net/pktgen/eth0
	for i in `seq 20`; do echo start > /proc/net/pktgen/pgctrl; tail -n1 /proc/net/pktgen/eth0; done

Before:
  746547-793084(786421+/-9.6e+03)pps 346-367(364.4+/-4.4)Mb/sec (346397808-367990976(3.649e+08+/-4.5e+06)bps) errors: 0

After:
  767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending out a burst of packets across multiple descriptors,
it is sufficient to send one LDC "start" trigger for
the first descriptor, so do not send an LDC "start" for every
pass through vnet_start_xmit. Similarly, it is sufficient to send
one "DRING_STOPPED" trigger for the last dring (and if that
fails, hold off and send the trigger later).

Optimizations to the number of LDC messages helps avoid
filling up the LDC channel with superfluous LDC messages
that risk triggering flow-control on the channel,
and also boosts performance.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NRaghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

calling ether_setup is redundant since alloc_etherdev calls
it.
Signed-off-by: NSubbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It will use pr_info_one() to print the version info of the
driver in probe function only once. No need to use the static
variable here.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_gro_frags allows skb re-use in case GRO can merge payload pages
into an skb on the GRO lists.

netperf TCP_STREAM, kvm-e1000 emulation, mtu 9k:
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec
old: 87380  16384  16384    30.00  8985.78
new: 87380  16384  16384    30.00  9907.05
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of preallocating Rx skbs, allocate them right before sending
inbound packet up the stack.

e1000-kvm, mtu1500, netperf TCP_STREAM:
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec
old: 87380  16384  16384    60.00    4532.40
new: 87380  16384  16384    60.00    4599.05
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

and remove *page, its only used for Rx.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000 uses the same metadata struct for Rx and Tx.  But Tx and Rx have
different requirements.

For Rx, we only need to store a buffer and a DMA address.

Follow-up patch will remove skb for Rx, bringing rx_buffer_info down
to 16 bytes on x86_64.

[ buffer_info is 48 bytes ]
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we unmap the DMA range, then copy to new skb.
Change this so we can keep the mapping in case the data is copied.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Its the same in both handlers.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

... and make it static.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change addresses several issues in the current ixgbe implementation of
busy poll sockets.

First was the fact that it was possible for frames to be delivered out of
order if they were held in GRO.  This is addressed by flushing the GRO buffers
before releasing the q_vector back to the idle state.

The other issue was the fact that we were having to take a spinlock on
changing the state to and from idle.  To resolve this I have replaced the
state value with an atomic and use atomic_cmpxchg to change the value from
idle, and a simple atomic set to restore it back to idle after we have
acquired it.  This allows us to only use a locked operation on acquiring the
vector without a need for a locked operation to release it.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write.  This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Resolve missing-field-initializers warnings by using
designated initialization.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cxgb4: Fix t4_flash_erase_sectors() to throw an error when requested to erase sectors which aren't in the FLASH

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Spansion S25FL032P flash
Based on original work by Dimitris Michailidis
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Free resources before being disconnected from phy and calling core driver is
wrong and should not happen. It avoids a delay of 4-5s caused by the timeout of
phy_disconnect().
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the much more common pr_warn instead of pr_warning.

Other miscellanea:

o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of looping in the code let's use kernel extension to dump small
buffers.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace mdelay with usleep_range to avoid busy loop.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the normal transmit completion path from dev_kfree_skb_any()
to dev_consume_skb_any() to help keep dropped packet profiling
meaningful.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usage of bond->lock in bond_main.c was completely unnecessary as it
didn't help to sync with anything, most of the spots already had RTNL.
Since there're no more users of bond->lock, remove it.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're safe to remove the bond->lock use from the arp targets because
arp_rcv_probe no longer acquires bond->lock, only rcu_read_lock.
Also setting the primary slave is safe because noone uses the bond->lock
as a syncing mechanism for that anymore.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use RCU to protect against slave release, the proc show function will sync
with the bond destruction by the proc locks and the fact that the bond is
released after NETDEV_UNREGISTER which causes the bonding to remove the
proc entry.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is necessary mainly for two bonding call sites: procfs and
sysfs as it was dereferenced without any real protection.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can remove the lock/unlock as it's no longer necessary since
RTNL should be held while calling bond_alb_set_mac_address().
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 3ad mode the only syncing needed by bond->lock is for the wq
and the recv handler, so change them to use curr_slave_lock.
There're no locking dependencies here as 3ad doesn't use
curr_slave_lock at all.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTNL should be already held in the notifier call so the slave list can
be traversed without a problem, remove the unnecessary bond->lock.

CC: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch defines a platform glue layer for Rockchip SoCs which
support arc-emac driver. It ensures that regulator for the rmii is on
before trying to connect to the ethernet controller. It applies right
speed and mode changes to the grf when ethernet settings change.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After merging the wireless-next tree, today's linux-next build (powerpc
allyesconfig) failed like this:

drivers/net/wireless/ath/ath5k/debug.c: In function 'open_file_eeprom':
drivers/net/wireless/ath/ath5k/debug.c:933:2: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
  buf = vmalloc(eesize);
  ^
drivers/net/wireless/ath/ath5k/debug.c:933:6: warning: assignment makes pointer from integer without a cast
  buf = vmalloc(eesize);
      ^
drivers/net/wireless/ath/ath5k/debug.c:960:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
  vfree(buf);
  ^

Caused by commit db906eb2 ("ath5k: added debugfs file for dumping
eeprom").  Also reported by Guenter Roeck.

I have used Geert Uytterhoeven's suggested fix of including vmalloc.h
and so added this patch for today:

From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Mon, 8 Sep 2014 18:39:23 +1000
Subject: [PATCH] ath5k: fix debugfs addition
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Suggested-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It removes the owner field updation of driver structure.
It will be automatically updated by module_platform_driver()
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW supports both rx and tx pause frames for flow control.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>