To get all device irq routing and to save them.

This is basically an implicit pci=routeirq enablement if (and on if)
the update_mptable boot option (which is off by default) has been
specified.

[ Impact: extend the update_mptable boot opion's scope ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <4A0DB7B4.4060702@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

should not call that if apic is disabled.

[ Impact: fix crash on certain UP configs ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <4A09CCBB.2000306@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

according to Ingo, io_apic irq-setup related functions have too many
parameters with a repetitive signature.

So reduce related funcs to get less params by passing a pointer
to a newly defined io_apic_irq_attr structure.

v2: io_apic_irq ==> irq_attr
    triggering ==> trigger

v3: add set_io_apic_irq_attr

[ Impact: cleanup ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A08ACD3.2070401@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Ed found that on 32-bit, boot_cpu_physical_apicid is not read right,
when the mptable is broken.

Interestingly, actually three paths use/set it:

 1. acpi: at that time that is already read from reg
 2. mptable: only read from mptable
 3. no madt, and no mptable, that use default apic id 0 for 64-bit, -1 for 32-bit

so we could read the apic id for the 2/3 path. We trust the hardware
register more than we trust a BIOS data structure (the mptable).

We can also avoid the double set_fixmap() when acpi_lapic
is used, and also need to move cpu_has_apic earlier and
call apic_disable().

Also when need to update the apic id, we'd better read and
set the apic version as well - so that quirks are applied precisely.

v2: make path 3 with 64bit, use -1 as apic id, so could read it later.
v3: fix whitespace problem pointed out by Ed Swierk
v5: fix boot crash

[ Impact: get correct apic id for bsp other than acpi path ]
Reported-by: NEd Swierk <eswierk@aristanetworks.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NCyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <49FC85A9.2070702@kernel.org>
[ v4: sanity-check in the ACPI case too ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

In case if apic were disabled by boot option
we still need read_apic operation. So fixmap
a fake apic area if needed.

[ Impact: fix boot crash ]
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: eswierk@aristanetworks.com
LKML-Reference: <20090511134140.GH4624@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Both print_local_APIC (used when apic=debug kernel param is set) and
cpu_debug code missed support for some extended APIC registers that
I'd like to see.

This adds support to show:

 - extended APIC feature register
 - extended APIC control register
 - extended LVT registers

[ Impact: print more debug info ]
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090508162350.GO29045@alberich.amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Ed found that on 32-bit, boot_cpu_physical_apicid is not read right,
when the mptable is broken.

Interestingly, actually three paths use/set it:

 1. acpi: at that time that is already read from reg
 2. mptable: only read from mptable
 3. no madt, and no mptable, that use default apic id 0 for 64-bit, -1 for 32-bit

so we could read the apic id for the 2/3 path. We trust the hardware
register more than we trust a BIOS data structure (the mptable).

We can also avoid the double set_fixmap() when acpi_lapic
is used, and also need to move cpu_has_apic earlier and
call apic_disable().

Also when need to update the apic id, we'd better read and
set the apic version as well - so that quirks are applied precisely.

v2: make path 3 with 64bit, use -1 as apic id, so could read it later.
v3: fix whitespace problem pointed out by Ed Swierk

[ Impact: get correct apic id for bsp other than acpi path ]
Reported-by: NEd Swierk <eswierk@aristanetworks.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NCyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <49FC85A9.2070702@kernel.org>
[ v4: sanity-check in the ACPI case too ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix fadt version checking

FADT2_REVISION_ID has value 3 aka rev 3 FADT. So need to use >= instead
of >, as other places in the code do.

[ Impact: extend scope of APIC boot quirk ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

So we can set io apic routing only when enabling the device irq.

This is advantageous for IRQ descriptor allocation affinity: if we set up
the IO-APIC entry later, we have a chance to allocate the IRQ descriptor
later and know which device it is on and can set affinity accordingly.

[ Impact: standardize/enhance irq-enabling sequence for mptable irqs ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C46E.8000501@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

So we could set io apic routing when ACPI is not enabled.

[ Impact: prepare for new functionality ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C422.5070400@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

To prepare those params for pcibios_irq_enable() to call setup_io_apic_routing().

[ Impact: extend function call API to prepare for new functionality ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C406.2040303@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Prepare to call setup_io_apic_routing() in pcibios_irq_enable()
also remove not needed member apic_id.

[ Impact: clean up, prepare for future change ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C3DD.3050104@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The patch to call mp_config_acpi_gsi() from the ACPI IRQ registration
code never got mainline because there were open discussions about it.

This call is needed to properly update the kernel's copy of the mptable,
when the update_mptable boot parameter is needed.

Now that the dust has settled with the APIC unification, and since there
were no objections when the patch was re-submitted, try this again.

[ Impact: fix the update_mptable boot parameter ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C387.7090103@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix the conditions when we stop updating the mptable due to
running out of slots.

[ Impact: fix memory corruption / non-working update_mptable boot parameter ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C3BB.1000609@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

We already have a per cpu vector on 32-bit via recent changes, and
don't need this trick any more (which trick obfuscates the real GSI
mappings and which only triggers on larger systems to begin with):

On 3 ioapic system (24 per ioapic) before patch I got:

ACPI: PCI Interrupt Link [ILSB] enabled at IRQ 71
IOAPIC[2]: Set routing entry (10-23 -> 0xa9 -> IRQ 64 Mode:1 Active:1)
pci 0000:80:01.1: PCI INT A -> Link[ILSB] -> GSI 71 (level, low) -> IRQ 64
ACPI: PCI Interrupt Link [LE5B] enabled at IRQ 67
IOAPIC[2]: Set routing entry (10-19 -> 0xb1 -> IRQ 65 Mode:1 Active:1)
pci 0000:83:00.0: PCI INT B -> Link[LE5B] -> GSI 67 (level, low) -> IRQ 65
ACPI: PCI Interrupt Link [LE5A] enabled at IRQ 66
IOAPIC[2]: Set routing entry (10-18 -> 0xb9 -> IRQ 66 Mode:1 Active:1)
pci 0000:83:00.1: PCI INT A -> Link[LE5A] -> GSI 66 (level, low) -> IRQ 66
ACPI: PCI Interrupt Link [LE5D] enabled at IRQ 65
IOAPIC[2]: Set routing entry (10-17 -> 0xc1 -> IRQ 67 Mode:1 Active:1)
pci 0000:84:00.0: PCI INT B -> Link[LE5D] -> GSI 65 (level, low) -> IRQ 67
ACPI: PCI Interrupt Link [LE5C] enabled at IRQ 64
IOAPIC[2]: Set routing entry (10-16 -> 0xc9 -> IRQ 68 Mode:1 Active:1)
pci 0000:84:00.1: PCI INT A -> Link[LE5C] -> GSI 64 (level, low) -> IRQ 68
pci 0000:87:00.0: PCI INT B -> Link[LE5A] -> GSI 66 (level, low) -> IRQ 66
pci 0000:87:00.1: PCI INT A -> Link[LE5D] -> GSI 65 (level, low) -> IRQ 67
pci 0000:88:00.0: PCI INT B -> Link[LE5C] -> GSI 64 (level, low) -> IRQ 68
pci 0000:88:00.1: PCI INT A -> Link[LE5B] -> GSI 67 (level, low) -> IRQ 65
pci 0000:8b:00.0: PCI INT B -> Link[LE5A] -> GSI 66 (level, low) -> IRQ 66
pci 0000:8b:00.1: PCI INT A -> Link[LE5D] -> GSI 65 (level, low) -> IRQ 67
pci 0000:8c:00.0: PCI INT B -> Link[LE5C] -> GSI 64 (level, low) -> IRQ 68
pci 0000:8c:00.1: PCI INT A -> Link[LE5B] -> GSI 67 (level, low) -> IRQ 65

after the patch we get:

ACPI: PCI Interrupt Link [ILSB] enabled at IRQ 71
IOAPIC[2]: Set routing entry (10-23 -> 0xa9 -> IRQ 71 Mode:1 Active:1)
pci 0000:80:01.1: PCI INT A -> Link[ILSB] -> GSI 71 (level, low) -> IRQ 71
ACPI: PCI Interrupt Link [LE5B] enabled at IRQ 67
IOAPIC[2]: Set routing entry (10-19 -> 0xb1 -> IRQ 67 Mode:1 Active:1)
pci 0000:83:00.0: PCI INT B -> Link[LE5B] -> GSI 67 (level, low) -> IRQ 67
ACPI: PCI Interrupt Link [LE5A] enabled at IRQ 66
IOAPIC[2]: Set routing entry (10-18 -> 0xb9 -> IRQ 66 Mode:1 Active:1)
pci 0000:83:00.1: PCI INT A -> Link[LE5A] -> GSI 66 (level, low) -> IRQ 66
ACPI: PCI Interrupt Link [LE5D] enabled at IRQ 65
IOAPIC[2]: Set routing entry (10-17 -> 0xc1 -> IRQ 65 Mode:1 Active:1)
pci 0000:84:00.0: PCI INT B -> Link[LE5D] -> GSI 65 (level, low) -> IRQ 65
ACPI: PCI Interrupt Link [LE5C] enabled at IRQ 64
IOAPIC[2]: Set routing entry (10-16 -> 0xc9 -> IRQ 64 Mode:1 Active:1)
pci 0000:84:00.1: PCI INT A -> Link[LE5C] -> GSI 64 (level, low) -> IRQ 64
pci 0000:87:00.0: PCI INT B -> Link[LE5A] -> GSI 66 (level, low) -> IRQ 66
pci 0000:87:00.1: PCI INT A -> Link[LE5D] -> GSI 65 (level, low) -> IRQ 65
pci 0000:88:00.0: PCI INT B -> Link[LE5C] -> GSI 64 (level, low) -> IRQ 64
pci 0000:88:00.1: PCI INT A -> Link[LE5B] -> GSI 67 (level, low) -> IRQ 67
pci 0000:8b:00.0: PCI INT B -> Link[LE5A] -> GSI 66 (level, low) -> IRQ 66
pci 0000:8b:00.1: PCI INT A -> Link[LE5D] -> GSI 65 (level, low) -> IRQ 65
pci 0000:8c:00.0: PCI INT B -> Link[LE5C] -> GSI 64 (level, low) -> IRQ 64
pci 0000:8c:00.1: PCI INT A -> Link[LE5B] -> GSI 67 (level, low) -> IRQ 67

As it can be seen that GSIs now get mapped lineary.

[ Impact: simplify irq number mapping on bigger 32-bit systems ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C35C.7060207@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Lockdep reports the warning below when Li tries to offline one cpu:

[  110.835487] =================================
[  110.835616] [ INFO: inconsistent lock state ]
[  110.835688] 2.6.30-rc4-00336-g8c9ed899 #52
[  110.835757] ---------------------------------
[  110.835828] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[  110.835908] swapper/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
[  110.835982]  (cmci_discover_lock){?.+...}, at: [<ffffffff80236dc0>] cmci_clear+0x30/0x9b

cmci_clear() can be called via smp_call_function_single().

It is better to disable interrupt while holding cmci_discover_lock,
to turn it into an irq-safe lock - we can deadlock otherwise.

[ Impact: fix possible deadlock in the MCE code ]
Reported-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A03ED38.8000700@jp.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Reported-by: Shaohua Li<shaohua.li@intel.com>

Tim Starling reported that crashdump will panic with kernel compiled
with CONFIG_KEXEC_JUMP due to null pointer deference in
machine_kexec_32.c: machine_kexec(), when deferencing
kexec_image. Refering to:

http://bugzilla.kernel.org/show_bug.cgi?id=13265

This patch fixes the BUG via replacing global variable reference:
kexec_image in machine_kexec() with local variable reference: image,
which is more appropriate, and will not be null.

Same BUG is in machine_kexec_64.c too, so fixed too in the same way.

[ Impact: fix crash on kexec ]
Reported-by: NTim Starling <tstarling@wikimedia.org>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
LKML-Reference: <1241751101.6259.85.camel@yhuang-dev.sh.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

If the first non-reserved (sub-)range doesn't fit the size requested,
an endless loop will be entered. If a range returned from
find_e820_area_size() turns out insufficient in size, the range must
be skipped before calling the function again.

[ Impact: fixes boot hang on some platforms ]
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Commit 7ad728f9
(cpumask: x86: convert cpu_sibling_map/cpu_core_map to cpumask_var_t)
changed the output of /proc/cpuinfo for siblings:

Example on an AMD Phenom:

  physical id   : 0
  siblings : 1
  core id	   : 3
  cpu cores  : 4

Before that commit it was:

  physical id	: 0
  siblings : 4
  core id	   : 3
  cpu cores  : 4

Instead of cpu_core_mask it now uses cpu_sibling_mask to count siblings.
This is due to the following hunk of above commit:

|  --- a/arch/x86/kernel/cpu/proc.c
|  +++ b/arch/x86/kernel/cpu/proc.c
|  @@ -14,7 +14,7 @@ static void show_cpuinfo_core(struct seq_file *m, struct cpuinf
|          if (c->x86_max_cores * smp_num_siblings > 1) {
|                  seq_printf(m, "physical id\t: %d\n", c->phys_proc_id);
|                  seq_printf(m, "siblings\t: %d\n",
|  -                          cpus_weight(per_cpu(cpu_core_map, cpu)));
|  +                          cpumask_weight(cpu_sibling_mask(cpu)));
|                  seq_printf(m, "core id\t\t: %d\n", c->cpu_core_id);
|                  seq_printf(m, "cpu cores\t: %d\n", c->booted_cores);
|                  seq_printf(m, "apicid\t\t: %d\n", c->apicid);

This was a mistake, because the impact line shows that this side-effect
was not anticipated:

   Impact: reduce per-cpu size for CONFIG_CPUMASK_OFFSTACK=y

So revert the respective hunk to restore the old behavior.

[ Impact: fix sibling-info regression in /proc/cpuinfo ]
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <20090504182859.GA29045@alberich.amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The feature bits should be set via bitmasks, not via feature IDs.

[ Impact: fix feature enabling in newer IOMMU versions ]
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20090504102028.GA30307@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

We may reach NULL dereference oops if kmalloc failed.
Prevent it with explicit BUG_ON.

[ Impact: more controlled assert in 'impossible' scenario ]
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Acked-by: NJack Steiner <steiner@sgi.com>
LKML-Reference: <20090501202511.GE4633@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The expression is known to be true/false at compilation
time so we're allowed to use build-time instead of
run-time check. Also align 'entry' items assignment.

[ Impact: shrink kernel a bit, cleanup ]
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090502093956.GB4791@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Replace recenly appeared printk with pr_ macro
(the file already use a lot of them).

[ Impact: cleanup ]
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090501195425.GB4633@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

commit db949bba (x86-32: use non-lazy
io bitmap context switching) broke ioperm for 32bit because it removed
the lazy initialization of io_bitmap_base and did not set it to the
real bitmap offset.

[ Impact: fix non-working sys_ioperm() on 32-bit kernels ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

move_irq_desc() will try to move irq_desc to the home node if
the allocated one is not correct, in create_irq_nr().

( This can happen on devices that are on different nodes that
  are using MSI, when drivers are loaded and unloaded randomly. )

v2: fix non-smp build
v3: add NUMA_IRQ_DESC to eliminate #ifdefs

[ Impact: improve irq descriptor locality on NUMA systems ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F95EAE.2050903@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Try to get irq_desc on the home node in create_irq_nr().

v2: don't check if we can move it when sparse_irq is not used
v3: use move_irq_des, if that node is not what we want

[ Impact: optimization, make MSI IRQ descriptors more NUMA aware ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F6559F.7070005@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Make actual use of the device parameter passed down to
io_apic_set_pci_routing() - to have the IRQ descriptor
on the home node of the device.

If no device has been passed down, we assume it's a platform
device and use the boot node ID for the IRQ descriptor.

[ Impact: optimization, make IO-APIC code more NUMA aware ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F6557E.3080101@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.

[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NLen Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.

v2: keep move_irq_desc related

[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.

v2: fix two typos

[ Impact: extend API ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The original feature of migrating irq_desc dynamic was too fragile
and was causing problems: it caused crashes on systems with lots of
cards with MSI-X when user-space irq-balancer was enabled.

We now have new patches that create irq_desc according to device
numa node. This patch removes the leftover bits of the dynamic balancer.

[ Impact: remove dead code ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F654AF.8000808@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

We will have systems with 2 and more sockets 8cores/2thread,
but we treat them as multi chassis - while they could have
a stable TSC domain.

Use DMI check instead.

[ Impact: do not turn possibly stable TSCs off incorrectly ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Ravikiran Thirumalai <kiran@scalex86.org>
LKML-Reference: <49F5532A.5000802@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

XAPIC_DEST_* is dupliicated to the one in apicdef.h

[ Impact: cleanup ]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <49F552D0.5050505@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The HPET in the ICH4M is not documented in the data sheet
because it was not officially validated.

While it is fine for hackers to continue to use "hpet=force"
to enable the hardware that they have, it is not prudent to
solicit additional "hpet=force" users on this hardware.

[ Impact: remove hpet=force syslog message on old-ICH systems ]
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <alpine.LFD.2.00.0904231918510.15843@localhost.localdomain>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The earlier patch to change the poller to a separate function subtly
broke the boot logging logic. This could lead to machine checks
getting logged at boot even when disabled or defaulting to off
on some systems. Fix that.

[ Impact: bug fix - avoid spurious MCE in log ]
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

The polling timer while running per CPU still uses a global next_interval
variable, which lead to some CPUs either polling too fast or too slow.   
This was not a serious problem because all errors get picked up eventually,
but it's still better to avoid it. Turn next_interval into a per cpu variable.

v2: Fix check_interval == 0 case (Hidetoshi Seto)

[ Impact: minor bug fix ]
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

uv_read_rtc() is referenced by read member of struct clocksource clocksource_uv.
In include/linux/clocksource.h, read of struct clocksource is declared as:
cycle_t (*read)(struct clocksource *cs)

This got introduced recently in:

   8e19608e: clocksource: pass clocksource to read() callback

But arch/x86/kernel/uv_time.c was not properly converted by that pach.

This patch adds a dummy parameter (struct clocksource type) to uv_read_rtc() to
fix the incompatible reference in clocksource_uv, and add a NULL parameter in
all places where uv_read_rtc() gets called.

[ Impact: cleanup, address compiler warning ]
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hugh@veritas.com>
LKML-Reference: <49EF3614.1050806@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Dimitri Sivanich <sivanich@sgi.com>

(See http://bugzilla.kernel.org/show_bug.cgi?id=12961)

It partially reverts commit c23e253e
(x86: hpet: stop HPET_COUNTER when programming periodic mode)

HPET on AMD 81xx chipset needs a second write (with HPET_TN_SETVAL
cleared) to T0_CMP register to set the period in periodic mode.

With this patch HPET_COUNTER is still stopped but not reset when HPET
is programmed in periodic mode. This should help to avoid races when
HPET is programmed in periodic mode and fixes a boot time hang that
I've observed on a machine when using 1000HZ.

[ Impact: fix boot time hang on machines with AMD 81xx chipset ]
Reported-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: NJeff Mahoney <jeffm@suse.com>
LKML-Reference: <20090421180037.GA2763@alberich.amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When interrupt-remapping is enabled, we are relying on
setup_IO_APIC_irqs() to configure remapped entries in the
IO-APIC, which comes little bit later after enabling
interrupt-remapping.

Meanwhile, restoration of old io-apic entries after enabling
interrupt-remapping will not make the interrupts through
io-apic functional anyway.

So remove the unnecessary reinit_intr_remapped_IO_APIC() step.

The longer story:

When interrupt-remapping is enabled, IO-APIC entries need to be
setup in the re-mappable format (pointing to
interrupt-remapping table entries setup by the OS). This
remapping configuration is happening in the same place where we
traditionally configure IO-APIC (i.e., in
setup_IO_APIC_irqs()).

So when we enable interrupt-remapping successfully, there is no
need to restore old io-apic RTE entries before we actually do a
complete configuration shortly in setup_IO_APIC_irqs(). Old
IO-APIC RTE's may be in traditional format (non re-mappable) or
in re-mappable format pointing to interrupt-remapping table
entries setup by BIOS. Restoring both of these will not make
IO-APIC functional. We have to rely on setup_IO_APIC_irqs() for
proper configuration by OS.

So I am removing this unnecessary and broken step.

[ Impact: remove unnecessary/broken IO-APIC setup step ]
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Acked-by: NWeidong Han <weidong.han@intel.com>
Cc: dwmw2@infradead.org
LKML-Reference: <20090420200450.552359000@linux-os.sc.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>