In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Always enable large page support; didn't seem to cause problems for anyone.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

...as required by IB Spec, C10-29.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

After PXE boot, the iw_nes driver does a full reset to ensure the card
is in a clean state.  However, it doesn't wait for firmware to
complete its work before issuing a port reset to enable the ports,
which leads to problems bringing up the ports.

The solution is to wait for firmware to complete its work before
proceeding with port reset.

This bug was flagged by Roland Dreier <rolandd@cisco.com>.

Cc: <stable@kernel.org>
Signed-off-by: NChien Tung <ctung@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Use NIPQUAD_FMT instead of printing raw 32-bit hex quantities in
debugging output.
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Removing open-coded MAC formats shrinks the source and the generated
code too, eg on x86-64:

add/remove: 0/0 grow/shrink: 0/4 up/down: 0/-103 (-103)
function                                     old     new   delta
make_cm_node                                 932     912     -20
nes_netdev_set_mac_address                   427     406     -21
nes_netdev_set_multicast_list               1148    1124     -24
nes_probe                                   2349    2311     -38
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Match what the PCI specification uses.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The PCI MSI interface is stubbed out properly so that all the
functions just return failure if PCI_MSI=n, so there's no reason to
have "#ifdef CONFIG_PCI_MSI" blocks in ipath_iba7220.c.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Before IBA7220 support was added, the ipath driver didn't support any
hardware unless PCI_MSI and/or HT_IRQ was enabled.  However, the
IBA7220 can generate INTx interrupts, so it makes sense to allow the
driver to be build even if PCI_MSI=n and HT_IRQ=n.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new IBA7220 code added a call to ipath_init_iba7220_funcs() that
is compiled unconditionally, but only built the IBA7220 code if
PCI_MSI is enabled.  Fix this by building the IBA7220 file
unconditonally.

This fixes build breakage when PCI_MSI=n, HT_IRQ=y and
INFINIBAND_IPATH=y reported by Ingo Molnar <mingo@elte.hu>:

 drivers/built-in.o: In function `ipath_init_one':
 ipath_driver.c:(.devinit.text+0x1e5bc): undefined reference to `ipath_init_iba7220_funcs'
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

IB/ipath: Remove reference to dev->class_dev                                                        
                                                                                                    
Commit 124b4dcb ("IB/ipath: add calls to new 7220 code and enable in                                
build") inadvertently added core to set dev->class_dev.dev back into                                
ib_ipath.  This is completely redundant since commit 1912ffbb ("IB: Set                             
class_dev->dev in core for nice device symlink"), which removed                                     
class_dev setting from low-level drivers, and also will break the build
when class_dev is removed completely from struct ib_device.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Describe disable_sma parameter with its name rather than the internal
ib_ipath_disable_sma variable name, so that the description shows up
properly in modinfo.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove redundant static declarations of functions that are defined
before they are used in the source.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This converts the main ib_device to use struct device instead of struct
class_device as class_device is going away.
Signed-off-by: NTony Jones <tonyj@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

The mlx4_ib driver is stable enough for production use, so bump the
version number to 1.0 to indicate this.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Also, introduce a few inline helper functions to make the code more readable.
Signed-off-by: NStefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Move the free_irq() call in nes_remove() to before the tasklet_kill();
otherwise there is a window after tasklet_kill() where a new interrupt
can be handled and reschedule the tasklet, leading to a use-after-free
crash.

Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ib_mthca driver has been stable for a while, so bump the version
number to 1.0 to indicate this.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a place where we might dereference a NULL pointer; this fixes
Coverity CID 1392.  On inspection I also found a place where we could
attempt to kmem_cache_free() a NULL pointer, so fix this too.
Signed-off-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NEli Cohen <eli@mellnaox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Handle IB_WR_SEND_WITH_INV work requests.

This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions.  Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated.  Add this new union to struct
ib_uverbs_send_wr.  Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().

Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.

Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit.  The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing).  Remove the flag from
all existing drivers that set it until we know which ones are OK.

The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.

This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds the initialization calls into the new 7220 HCA files,
changes the Makefile to compile and link the new files, and code to
handle send DMA.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The patch adds a number of minor changes to support newer HCAs:
 - New send buffer control bits
 - New error condition bits
 - Locking and initialization changes
 - More send buffers
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A new file which allows the IBA7220 send DMA engine to be used from
userland.  The routines here are not linked in yet, that will happen in
a follow-on patch...
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A new header file which allows the IBA7220 send DMA engine to be used
from userland.  The definitions here are not used yet, that will happen
in a follow-on patch...
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IBA7220 HCA has a new feature to DMA data to the on chip send
buffers instead of or in addition to the host CPU doing the data
transfer.  This patch adds code to support the send DMA queue.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds binary data to initialize the IB SERDES.
Signed-off-by: NMichael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The control and initialization of the SerDes blocks of the IBA7220 is
sufficiently complex to merit a separate file.
Signed-off-by: NMichael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds the HCA-specific code for the IBA7220 HCA.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>