Latest smc91x driver allows you to specify settings in board resources
rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The interrupt probe workaround doesn't work without hacks to common code,
and the add-on card only needs a simple resistor to fix the problem, so
drop the board-specific hack.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Push the device table to the board resources as data interpretation can be
changed on a per-board basis.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The AD7142 add-on card hooks the IRQ line up to PG5, not PF5.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The port1 disable stuff was dropped from the USB ISP1760, so update the
Blackfin boards accordingly.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Many aspects of the Blackfin memory map is exactly the same across all
variants.  Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file.  In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Update anomaly headers to match latest released anomaly sheets.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The ADP5520 hooks up to PF7 rather than PG0.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Blackfin SPI driver can be driven by an IRQ now, so declare it in
the board resources.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Try to keep the naming conventions consistent, so:
	SPI_ADC_BF533 -> BFIN_SPI_ADC
	TWI_LCD       -> BFIN_TWI_LCD
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

For systems where the core cycles are not a usable tick source (like SMP
or cycles gets updated), enable gptimer0 as an alternative.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Make sure the addresses declared match reality, and make the PATA IRQ code
optional.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Both software emulated and hardware based CTS and RTS are enabled in
serial driver.

The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device.  In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Only the CTS bit is affected.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

ADP5520 Multifunction LCD Backlight and Keypad Input Device Driver
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Provide option to use the platfrom PATA driver with CF Cards
on the CF-IDE-NAND Add-On-Card in Common Memory Mode
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

I have a system where UART0 is configured with hardware flow control, but UART1
doesn't have it enabled. Attempting to access UART1 in this configuration
results in the following error in dmesg:

<3>bfin-gpio: GPIO 0 is already reserved as Peripheral by bfin-uart !
<5>Stack from 0082bc7c:
<5>        0082bc88 00404dd6 00000003 00000000 0054051e 004079da 0082bcb4
00000000
<5>        00000003 00000000 0052686c 0113f2a0 005fa3f0 00000032 20515249
00003035
<5>        00427228 00526e50 0113f2e0 005fa3f0 00000032 0113f2e0 0054b748
0000ffff
<5>        22222222 22222222 004e1628 00427304 00000000 00000032 00000023
0054b748
<5>        00487a94 0054b7e8 0054b748 0000000b 00487fb8 0054b748 0054b748
00000001
<5>        0000000a 005fa3f0 009d4fe8 0101e3c0 0054b748 005fa3f0 0050b134
0054b748
<5>
<5>Call Trace:
<4>[<00485c16>] _uart_startup+0x56/0x178
<4>[<004865c8>] _uart_open+0x40/0x3e0
<4>[<0048661c>] _uart_open+0x94/0x3e0
<4>[<0047f1ce>] _init_dev+0x1fa/0x450
<4>[<004e1628>] ___mutex_unlock_slowpath+0x30/0xe8
<4>[<004815da>] _tty_open+0xf6/0x21c
<4>[<0043dab0>] ___path_lookup_intent_open+0x34/0x7c
<4>[<004375e4>] _chrdev_open+0x7c/0x134
<4>[<0043dc2c>] _open_namei+0x60/0x568
<4>[<00433fa2>] ___dentry_open+0x9e/0x188
<4>[<00437568>] _chrdev_open+0x0/0x134
<4>[<0043410c>] _nameidata_to_filp+0x30/0x3c
<4>[<00434152>] _do_filp_open+0x3a/0x44
<4>[<00408826>] _task_running_tick+0x102/0x278
<4>[<0043418e>] _do_sys_open+0x32/0xac
<4>[<0043ede4>] _sys_ioctl+0x28/0x50
<4>[<0043edbc>] _sys_ioctl+0x0/0x50
<4>[<00434224>] _sys_open+0x18/0x20
<4>[<0043420c>] _sys_open+0x0/0x20
<4>[<00418174>] _sys_setuid+0x0/0xc8

This is because the #ifdef's in bfin_serial_5xx.h are messed up. More
specifically, they add/remove the uart_{rts,cts}_pin fields in
bfin_serial_resources based on whether the particular port has rts/cts enabled,
as opposed to when either port has it enabled.

This patch fixed this.
Signed-off-by: NTom Parker <blackfin@tevp.net>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

make sure ANOMALY_05000278/ANOMALY_05000380 is defined for all parts
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

[Mike Frysinger <vapier.adi@gmail.com>:
 - setup P_DEFAULT_BOOT_SPI_CS  for every arch based on
   the default bootrom behavior and convert all our boards
   to it
 - revert previous anomaly change ... bf51x is not affected
   by anomaly 05000353]
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NGrace Pan <grace.pan@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

[Mike Frysinger <vapier.adi@gmail.com>:
 - handle bf531/bf532/bf534/bf536 variants in ipipe.h
 - cleanup IPIPE logic for bfin_set_irq_handler()
 - cleanup ipipe asm code a bit and add missing ENDPROC()
 - simplify IPIPE code in trap_c
 - unify some of the IPIPE code and fix style
 - simplify DO_IRQ_L1 handling with ipipe code
 - revert IRQ_SW_INT# addition from ipipe merge
 - remove duplicate get_{c,s}clk() prototypes
]
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>