Interpret NFTA_NAT_REG_ADDR_MAX if NFTA_NAT_REG_ADDR_MIN is present,
otherwise, skip it. Same thing with NFTA_NAT_REG_PROTO_MAX.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

We have to validate that we at least get an NFTA_NAT_REG_ADDR_MIN or
NFTA_NFT_REG_PROTO_MIN attribute. Reject the configuration if none
of them are present.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

We have to validate the real chain type to ensure that matches/targets
are not used out from their scope (eg. MASQUERADE in nat chain type).
The existing validation relies on the table name, but this is not
sufficient since userspace can fool us by using the appropriate table
name with a different chain type.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Set hook_mask to zero for non-base chains, otherwise people may hit
bogus errors from the xt_check_target() and xt_check_match() when
validating the uninitialized hook_mask.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This adds the missing validation code to avoid the use of nat/masq from
non-nat chains. The validation assumes two possible configuration
scenarios:

1) Use of nat from base chain that is not of nat type. Reject this
   configuration from the nft_*_init() path of the expression.

2) Use of nat from non-base chain. In this case, we have to wait until
   the non-base chain is referenced by at least one base chain via
   jump/goto. This is resolved from the nft_*_validate() path which is
   called from nf_tables_check_loops().

The user gets an -EOPNOTSUPP in both cases.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

[   23.545204] nf_reject_ipv4: module license 'unspecified' taints kernel.

Fixes: c8d7b98b ("netfilter: move nf_send_resetX() code to nf_reject_ipvX modules")
Reported-by: NDave Young <dyoung@redhat.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Florian Fainelli says:

====================
net: bcmgenet & systemport fixes

This patch series fixes an off-by-one error introduced during a previous
change, and the two other fixes fix a wake depth imbalance situation for
the Wake-on-LAN interrupt line.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:

1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt

After step 4), SYSTEMPORT would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:

1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt

After step 4), GENET would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b629be5c ("net: bcmgenet: check
harder for out of memory conditions") moved the increment of the local
read pointer *before* reading from the hardware descriptor using
dmadesc_get_length_status(), which creates an off-by-one situation.

Fix this by moving again the read_ptr increment after we have read the
hardware descriptor to get both the control block and the read pointer
back in sync.

Fixes: b629be5c ("net: bcmgenet: check harder for out of memory conditions")
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: fix races accessing page->_count

This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.

The only case it is valid is when page->_count is 0, we can use this in
__netdev_alloc_frag()

Note that I never seen crashes caused by these races, the issue was reported
by Andres Lagar-Cavilla and Hugh Dickins.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.

The only case it is valid is when page->_count is 0

Fixes: 540eb7bf ("net: Update alloc frag to reduce get/put page usage and recycle pages")
Signed-off-by: NEric Dumaze <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz
and 50MHz. Both PHYs differ in the default frequency they expect
after reset. If this differs from the actual input clock, then
register 0x1f bit 7 must be changed.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses a kernel unaligned access bug seen on a sparc64 system
with an igb adapter.  Specifically the __skb_flow_get_ports was returning a
be32 pointer which was then having the value directly returned.

In order to prevent this it is actually easier to simply not populate the
ports or address values when an skb is not present.  In this case the
assumption is that the data isn't needed and rather than slow down the
faster aligned accesses by making them have to assume the unaligned path on
architectures that don't support efficent unaligned access it makes more
sense to simply switch off the bits that were copying the source and
destination address/port for the case where we only care about the protocol
types and lengths which are normally 16 bit fields anyway.
Reported-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. sk_run_filter has been renamed, sk_filter() is using SK_RUN_FILTER.
2. Remove wrong comments about storing intermediate value.
3. replace sk_run_filter with __bpf_prog_run for check_load_and_stores's
comments

Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__sk_run_filter has been renamed as __bpf_prog_run, so replace them in comments
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jason Baron says:

====================
macvlan: optimize receive path

So after porting this optimization to net-next, I found that the netperf
results of TCP_RR regress right at the maximum peak of transactions/sec. That
is as I increase the number of threads via the first argument to super_netperf,
the number of transactions/sec keep increasing, peak, and then start
decreasing. It is right at the peak, that I see a small regression with this
patch (see results in patch 2/2).

Without the patch, the ksoftirqd threads are the top cpu consumers threads on
the system, since the extra 'netif_rx()', is queuing more softirq work, whereas
with the patch, the ksoftirqd threads are below all of the 'netserver' threads
in terms of their cpu usage. So there appears to be some interaction between how
softirqs are serviced at the peak here and this patch. I think the test results
are still supportive of this approach, but I wanted to be clear on my findings.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netif_rx() call on the fast path of macvlan_handle_frame() appears to
be there to ensure that we properly throttle incoming packets. However, it
would appear as though the proper throttling is already in place for all
possible ingress paths, and that the call is redundant. If packets are arriving
from the physical NIC, we've already throttled them by this point. Otherwise,
if they are coming via macvlan_queue_xmit(), it calls either
'dev_forward_skb()', which ends up calling netif_rx_internal(), or else in
the broadcast case, we are throttling via macvlan_broadcast_enqueue().

The test results below are from off the box to an lxc instance running macvlan.
Once the tranactions/sec stop increasing, the cpu idle time has gone to 0.
Results are from a quad core Intel E3-1270 V2@3.50GHz box with bnx2x 10G card.

for i in {10,100,200,300,400,500};
do super_netperf $i -H $ip -t TCP_RR; done
Average of 5 runs.

trans/sec 		 trans/sec
(3.17-rc7-net-next)      (3.17-rc7-net-next + this patch)
----------               ----------
208101                   211534 (+1.6%)
839493                   850162 (+1.3%)
845071                   844053 (-.12%)
816330                   819623 (+.4%)
778700                   789938 (+1.4%)
735984                   754408 (+2.5%)
Signed-off-by: NJason Baron <jbaron@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass last argument to macvlan_count_rx() as the correct bool type.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
Add 10GbE support to APM X-Gene SoC ethernet driver

Adding 10GbE support to APM X-Gene SoC ethernet driver.

v4: Address comments from v3
* dtb: resolved merge conflict for the net tree

v3: Address comments from v2
* dtb: changed to use all-zeros for the mac address

v2: Address comments from v1
* created preparatory patch to review before adding new functionality
* dtb: updated to use tabs consistently

v1:
* Initial version
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Added 10GbE support
- Removed unused macros/variables
- Moved mac_init call to the end of hardware init
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Rearranged code to pave the way for adding 10GbE support
- Added mac_ops structure containing function pointers for mac specific functions
- Added port_ops structure containing function pointers for port specific functions
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added 10GbE interface and clock nodes.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updated APM X-Gene ethernet driver maintainers list.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

minimal configurations where EPOLL, PERF_EVENTS, etc are disabled,
but NET is enabled, are failing to build with link error:
kernel/built-in.o: In function `bpf_prog_load':
syscall.c:(.text+0x3b728): undefined reference to `anon_inode_getfd'

fix it by selecting ANON_INODES when NET is enabled
Reported-by: NMichal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net-next

This batch contains two fixes for what you have in your net-next,
they are:

1) Remove nf_send_reset6() from header file. This function now resides
   in the nf_reject_ipv6 module. Reported by Eric Dumazet.

2) Fix wrong NFT_REJECT_ICMPX_MAX definition and adjust code to fix
   errors reported by Dan Carpenter's static analysis tools.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'master-2014-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
pull request: wireless-next 2014-10-09

Please pull this batch of fixes intended for the 3.18 stream!

Andrea Merello makes rtl818x_pci use a more reasonable transmission
rate for HW generated frames.

Fabian Frederick tweaks some kernel-doc bits to avoid warnings.

Larry Finger corrects a possible unaligned access in the rtlwifi code.

Marek Puzyniak avoids a kernel panic in ath9k_hw_reset.

Sujith Manoharan goes for the hat trick -- he fixes a smatch warning
in the shared ath code, he fixes a crash in ath9k, and he corrects
a sequence number assignment problem in ath9k too.

For ease of merging, I pulled the last bits of the wireless tree as well...

Please let me know if there are problems!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing revealed that the local variable mc_filter was dimensioned
incorrectly for all possible configurations and get_mac_addr should
have been set_mac_addr (a typo). Make sure mc_filter is dimensioned
to 8 32-bit unsigned longs - the largest size of the Synopsys
multicast filter register set.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `rxq_deinit':
pxa168_eth.c:(.text+0x2a2f2e): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_reclaim':
pxa168_eth.c:(.text+0x2a3044): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `txq_deinit':
pxa168_eth.c:(.text+0x2a310a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_init':
pxa168_eth.c:(.text+0x2a3226): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_init':
pxa168_eth.c:(.text+0x2a32d4): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `init_hash_table':
pxa168_eth.c:(.text+0x2a3354): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_refill':
pxa168_eth.c:(.text+0x2a345a): undefined reference to `dma_map_single'
drivers/built-in.o: In function `rxq_process':
pxa168_eth.c:(.text+0x2a39cc): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `pxa168_eth_remove':
pxa168_eth.c:(.text+0x2a3b84): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `pxa168_eth_start_xmit':
pxa168_eth.c:(.text+0x2a3e8a): undefined reference to `dma_map_single'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The latest linus git tip (3.18-rc1) fails with the following build failure. Fix
this by making PTP support explicit for fm10k driver.

rivers/built-in.o: In function `fm10k_ptp_register':
(.text+0x12e760): undefined reference to `ptp_clock_registER'
drivers/built-in.o: In function `fm10k_ptp_unregister':
(.text+0x12e7dc): undefined reference to `ptp_clock_unregister'
Makefile:930: recipe for target 'vmlinux' failed
Signed-off-by: NPranith Kumar <bobby.prani@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[linux-devel:devel-hourly-2014100909 3763/3915] drivers/net/ethernet/freescale/fs_enet/mac-scc.c:119:32: error: 'SCCE_ENET_TXF' undeclared

Due to patch d43a396a net: fs_enet: Add NAPI TX, it appears that some target
compilations are broken.
This is due to the fact that unlike the FEC, the SCC and FCC don't have a TXF
event (complete Frame transmitted) but only TXB (buffer transmitted).
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restore the quota fairness between qdisc's, that we broke with commit
5772e9a3 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE").

Before that commit, the quota in __qdisc_run() were in packets as
dequeue_skb() would only dequeue a single packet, that assumption
broke with bulk dequeue.

We choose not to account for the number of packets inside the TSO/GSO
packets (accessable via "skb_gso_segs").  As the previous fairness
also had this "defect". Thus, GSO/TSO packets counts as a single
packet.

Further more, we choose to slack on accuracy, by allowing a bulk
dequeue try_bulk_dequeue_skb() to exceed the "packets" limit, only
limited by the BQL bytelimit.  This is done because BQL prefers to get
its full budget for appropriate feedback from TX completion.

In future, we might consider reworking this further and, if it allows,
switch to a time-based model, as suggested by Eric. Right now, we only
restore old semantics.

Joint work with Eric, Hannes, Daniel and Jesper.  Hannes wrote the
first patch in cooperation with Daniel and Jesper.  Eric rewrote the
patch.

Fixes: 5772e9a3 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: use mutex for hw settings

v2:
Make sure the autoresume wouldn't occur inside the mutex, otherwise
the dead lock would happen. For the purpose, adjust some code about
autosuspend/autoresume.

v1:
Use mutex to avoid that the serial hw settings would be interrupted
by other settings. Although there is no problem now, it makes the
driver more safe.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the mutex to avoid the settings are interrupted by other ones.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>