Commit ac4c2a3b broke the build
of all powerpc boot wrappers.

It attempts to add an include of autoconf.h but used the wrong
path for it. It also adds -D__KERNEL__ to our boot wrapper, both
things that we pretty much didn't do on purpose so far.

We want our boot wrapper to remain independent enough of the kernel
for various reasons, one of them being that you can "wrap" an existing
kernel at distro install time which allows to ship one kernel image
and a set of boot wrappers for different platforms, the wrappers
don't have to be built out of the same kernel build tree.

It's also incorrect to do what the patch does in our boot environment
since we may not have a proper alignment exception handler which means
we may not be able to fixup the few cases where an unaligned access will
need SW emulation (depends on the core variant, could be when crossing
page or segment boundaries for example).

This patch fixes it by putting the old code back in and using the
new "fancy" variant only when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
is set, which happens not to be set on powerpc since we don't include
autoconf.h. It also reverts the changes to our boot wrapper Makefile.

This means that x86 should, afaik, keep the optimisations since its
boot wrapper does include autoconf.h and define __KERNEL__ (though I
doubt they make that much different outside of slow embedded processors).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sys_recvmmsg is reachable via sys_socketcall. So unwire it again since
there is no point in having two entry points for it.
Also put it to the ignore list so we don't get reminded anymore in order
to wire it up.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This one will trap, generates shorter code and emits better debug data
than the generic version.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Finally move it to the place where it belongs to and make get rid of
it for !CONFIG_SMP.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove pointless qualifier.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

smp_processor_id() is supposed to work before setup_arch() gets called.
Before that smp_processor_id() may return just an arbitrary value that
is contained in the uninitialized boot lowcore.
So provide the arch function which will override the weak function in
init/main.c.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.

I.e. either use rlimit helpers added in
3e10e716
or ACCESS_ONCE if not applicable.

Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The TIF_USEDFPU bit is always 0 for s390 and it is not tested anywhere.
Remove the bit. At the same time remove the calls to clear_used_math()
as well. The PF_USED_MATH bit is never set for s390 either.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The code in do_signal sets the TIF_SINGLE_STEP bit and calls
tracehook_signal_handler after the signal frame has been set up.
This causes two SIGTRAP signals to be delivered to the tracer.
Stop setting the TIF_SINGLE_STEP bit in do_signal to get the
correct number of SIGTRAPs.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Clear the TIF_SINGLE_STEP bit in copy_thread. The new process did not get
a PER event of its own. It is wrong deliver a SIGTRAP that was meant for
the parent process.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If the current task enables / disables PER tracing for itself the
PER control registers need to be loaded in FixPerRegisters.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Setting LC_CTYPE=C breaks localized messages in some setups. With only
LC_COLLATE=C and LC_NUMERIC=C, we get almost all we need, except for not
so defined character classes and tolower()/toupper(). The former is not
a big issue, because we can assume that e.g. [:alpha:] will always
include a-zA-Z and we only ever process ASCII input. The latter seems
only affect arch/sh/tools/gen-mach-types, which we can handle separately.

So after this patch the meaning of ranges like [a-z], the behavior of
sort and join, etc. should be the same everywhere and at the same time
gcc should be able to print localized waring and error messages.
LC_NUMERIC=C might not be necessary, but setting it doesn't hurt.
Reported-by: NSimon Horman <horms@verge.net.au>
Reported-by: NSergei Trofimovich <slyfox@inbox.ru>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Tested-by: NSimon Horman <horms@verge.net.au>
Tested-by: NMasami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

Fix compilation breakage of all m68knommu targets:

  CC      arch/m68knommu/kernel/asm-offsets.s
In file included from include/linux/sched.h:77,
                 from arch/m68knommu/kernel/asm-offsets.c:12:
include/linux/percpu.h: In function 'per_cpu_ptr_to_phys':
include/linux/percpu.h:161: error: implicit declaration of function 'virt_to_phy

This is broken in linux-2.6.33-rc3.

Change the definitions of __pa() and __va() to not use virt_to_phys()
and phys_to_virt(). Trivial 1:1 conversion required for the non-MMU case.

A side effect if this is that the m68knommu can now use asm/virtconvert.h
for the definition of virt_to_phys() and phys_to_virt().

Also cleaned up the definition of page_to_phys() when moving into
virtconvert.h.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for.  Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/795/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It moves to the same directory as the boot files in other formats.
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/796/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:

# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65

Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:

# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/831/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

With typical mult and shift values, the calculation for Octeon's sched_clock
overflows when using 64-bit arithmetic.  Use 128-bit calculations instead.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/849/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/813/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Builtin cmdline is copied by arch_mem_init().
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/812/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/811/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A call to r4k_clocksource_init() was added to plat_time_init(), but
when init_mips_clock_source() calls the same function, boot fails in
clockevents_register_device(). This patch removes the extraneous call.
Signed-off-by: NDavid VomLehn <dvomlehn@cisco.com>
Patchwork: http://patchwork.linux-mips.org/patch/803/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Tested with CoLo v1.22
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/807/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

With the advent of function graph tracing on MIPS, Octeon needs a high
precision sched_clock() implementation.  Without it, most timing
numbers are reported as 0.000.

This new sched_clock just uses the 64-bit cycle counter appropriately
scaled.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/805/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 898d357b5262f9e26bc2418e01f8676e80d9867e (lmo) /
6acc7d48 (kernel.org) ("Fix and enhance
built-in kernel command line") arcs_cmdline[] does not contain built-in
command line.  The commit introduce CONFIG_CMDLINE_BOOL and
CONFIG_CMDLINE_OVERRIDE to control built-in command line, and now we can
use them instead of platform-specific built-in command line processing.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Patchwork: http://patchwork.linux-mips.org/patch/802/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/801/Reviewed-by: NDavid VomLehn <dvomlehn@cisco.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/800/Reviewed-by: NDavid VomLehn <dvomlehn@cisco.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

mips_machine_halt() is same as mips_machine_restart().  Also delete the
registration of _machine_halt and pm_power_off because mips_machine_halt()
is the restart function.
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/798/Reviewed-by: NDavid VomLehn <dvomlehn@cisco.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/799/Reviewed-by: NDavid VomLehn <dvomlehn@cisco.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/797/Reviewed-by: NDavid VomLehn <dvomlehn@cisco.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

An unused leftover from the old KGDB implementation.
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/794/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

sizeof(dp) is just the size of the pointer.  Change it to the size of the
referenced structure.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression *x;
expression f;
type T;
@@

*f(...,(T)x,...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Patchwork: http://patchwork.linux-mips.org/patch/789/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NFlorian Fainelli <ffainelli@freebox.fr>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/784/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 o Remove the .initrd section.  The initrd section was already handled
   when vmlinux was linked.
 o Discard .MIPS.options, .options, .pdr, .reginfo, .comment and .note
   sections.  If .MIPS.options is not removed, kernels compiled with gcc
   3.4.6 will not boot.
 o Clean up the file format.
 o Remove several other unneeded sections.

Tested with GCC 3.4.6 and 4.4.1 with and without initrd.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/785/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

commit c8af165342e83a4eb078c9607d29a7c399d30a53 (lmo) rsp.
e0cc87f5 (kernel.org) left
label_module_alloc unused.  Remove it now.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/752/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Revert commit 2fbd07a5, as this commit
breaks an IBM platform with quad-core Xeon cpu's.

According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).

Revert this for now because of the IBM platform breakage.

Another version will be re-submitted after the complete analysis.
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The list macros use LIST_POISON1 and LIST_POISON2 as undereferencable
pointers in order to trap erronous use of freed list_heads.  Unfortunately
userspace can arrange for those pointers to actually be dereferencable,
potentially turning an oops to an expolit.

To avoid this allow architectures (currently x86_64 only) to override
the default values for these pointers with truly-undereferencable values.
This is easy on x86_64 as the virtual address space is large and contains
areas that cannot be mapped.

Other 64-bit architectures will likely find similar unmapped ranges.

[ingo: switch to 0xdead000000000000 as the unmapped area]
[ingo: add comments, cleanup]
[jaswinder: eliminate sparse warnings]
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>