DWC3's tx-fifo-resize property has been deprecated
because of it being unnecessary to any HW other than
OMAP5 ES1.0.
Signed-off-by: NFelipe Balbi <balbi@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds an idle pinctrl state, which will be used
by the driver to avoid incoming data during clock
rate changes or data flushing.
Signed-off-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MCLK is provided by an external clock of 24.576MHz.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

UART0 device is the device to be used for boot console output.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Provide RESET GPIO for the USB PHY, the USB Host port mode and
the PHY device for the controller. Also provides pin multiplexer
information for USB host pins.
Signed-off-by: NPau Pajuel <ppajuel@gmail.com>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

UART3 device is the device to be used for boot console output.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch defines the pin muxing to configure the hsusb0 through
the twl4030 PMIC, because we can't always assume the bootloader will
do it correctly.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Nokia N950 and Nokia N9 have a modem attached to their
first ssi port. This change adds the modem to the SSI port.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Nokia N950 and Nokia N9 have a modem attached to their
first ssi port. This change adds all necessary information
to initialize the SSI module, but does not yet add the
modem information.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The devkit has an AT25 EEPROM on MCSPI1. Enable this with default
parameters.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Setup regulator and fix pin muxing to allow Panel to sleep and
wake from sleep for some low power improvements.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Wireless version of the SOM uses an AT24 EEPROM to store product ID.
The EEPROM is readonly.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Logic PD Torpedo standard kits come with a SOM populated to us an
8-bit parallel camera interface.  This patch pin muxes the omap3-isp
pins, sets the MT9P031 clicks, and configures the i2c2 bus to communicate
with the mt9p031 on address 0x48.

I have not done a lot of testing, but when modprobing
mt9p031, then omap3-isp, the board responds with
MT9P031 detected at address 0x48.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The USB2 PHY2 has a different register map compared to USB2 PHY1
to power on/off the PHY. In order to handle it, use the new compatible
string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add "syscon-phy-power" property and "syscon-pcs" property which can
be used to perform the control module initializations and remove
the deprecated "ctrl-module" property from PCIe PHY dt nodes.

Phandle to "sysclk" clock node is also added to the PCIe PHY node
since some of the syscon initializations is based on system clock
frequency.

Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree
nodes are no longer used, remove it.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add new device tree node for the control module register space where
PCIe registers are present.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add NAND support for dm8148-evm.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add NAND support for j5-eco evm.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for GPMC for dm814x and dra62x
Signed-off-by: NTony Lindgren <tony@atomide.com>

The rate for auxclk is 22.59792 by default.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for the wl1271 wlan chip. As far as I can see N9 uses the
same chip with the same enable and irq gpio, but they use the mmc
interface instead of the spi interface.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Device tree modifications:
- Pinmux for SPI0 and WiFi GPIOs.
- SPI0 node with wlcore as a child node.
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The TLV320AIC23B codec is connected to the CPU by McASP controller 1 for
data and I2C0 for control.

Modifications:
- Enable and configure McASP controller 1.
- Add TLV320AIC23B codec pinmux.
- Add TLV320AIC23B codec configurations.
- Use simple-audio-card as CPU to codec glue.
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Touchscreen and analog digital converter configurations.
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add CAN bus pinmux.
Enable D_CAN bus controllers 0 and 1

The pinmux of uart1 node contradicts the pinmux of dcan0 and dcan1 nodes.
U-Boot should delete the uart1 or dcan0/1 nodes.
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Driver for omap3 with documentation is there since v4.4-rc1.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Tested-by: NPavel Machek <pavel@ucw.cz>
[tony@atomide.com: added thermal-sensor-cells as suggested by Roger]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds adp1653 device into n900 DT structure. DT support in
adp1653 driver is there since v4.2-rc1 version.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On r8a7740/armadillo, actual clock rates are ca. 4% lower than reported
by /sys/kernel/debug/clk/clk_summary. Correct the extal1 frequency from
25 MHz to 24 MHz to fix this.

This matches the Armadillo-800 EVA Product Manual, which claims the main
crystal runs at 24 MHz, and the old legacy/reference board code.

Fixes: 25aa7ba3 ("ARM: shmobile: armadillo800eva: Sync DTS")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable PCIe DT node and fill PCIe DT node with regulator, pinctrl and reset
GPIO, to use the PCIe on the ifc6410 board.
Signed-off-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Add the PCIe DT node so that it can probe and be used.
Signed-off-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The device tree version of Versatile AP/PB never had LED support
so we are missing LEDs from our hardware boards. Add this as
syscon LEDs like we did for Integrator and Juno. We need to
spawn devices in the syscon with "simple-mfd" for this to work.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

According to datasheet, the registers space of SDHC controller is 1Kb,
not '0x1000', the correct value should be '0x400'. Bracket interrupt
numbers individually per recommendations.
Signed-off-by: NRoman Volkov <rvolkov@v1ros.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
Signed-off-by: NRoman Volkov <rvolkov@v1ros.org>
Reviewed-by: NAlexey Charkov <alchark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Commit 0976c946
"arm/versatile: Fix versatile irq specifications"
has an off-by-one error on the Versatile AB that has
been regressing the Versatile AB hardware for some time.

However it seems like the interrupt assignments have
never been correct and I have now adjusted them according
to the specification. The masks for the valid interrupts
made it impossible to assign the right SIC interrupt
for the MMCI, so I went in and fixed these to correspond
to the specifications, and added references if anyone
wants to double-check.

Due to the Versatile PB including the Versatile AB
as a base DTS file, we need to override and correct
some values to correspond to the actual changes in the
hardware.

For the Versatile PB I don't think the IRQ line
assignment for MMCI has ever been correct for either of
the two MMCI blocks. It would be nice if someone with the
physical PB board could test this.

Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.

Cc: Rob Herring <robh@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: stable@vger.kernel.org
Fixes: 0976c946 ("arm/versatile: Fix versatile irq specifications")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The Nomadik has sporadic crashes because of these latencies, setting
them to max makes the platform work nicely, so use this values for
now.

These latencies were set to 2 since the Nomadik platform was merged,
but I suspect they never took effect until the right size and
associativity for the cache was specified in the device tree and
that is why the crash comes now.

Cc: stable@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The pinctrl group ipu2grp is a leftover from the previous iomuxc DT
cleanup.  It's not used by anyone now.  More importantly, it's getting
in the way of saving the unnecessary pinfunc container node from the
board dts files that include imx6q.dtsi.

Let's clean it up.
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Tested-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>