Nothing outside of x86 can use that code.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Fix section mismatch by annotating using variable name suffix.
Signed-off-by: NNikanth Karthikesan <knikanth@suse.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The device table is required to load modules based on modaliases.

After adding MODULE_DEVICE_TABLE, below entries will be added to
modules.pcimap:

  pch_gpio             0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
  ml_ioh_gpio          0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The function gen_74x164_remove and mc33880_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to modules.pcimap:

pch_gpio             0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio          0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.

The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

pca953x_get_alt_pdata() uses uint16_t* as result type for
of_get_property(), but numeric of values are __be32.

Checking for negative values is bogus because of-property
values are unsigned by definition.
Instead check for proper property size.

v3: - assume big-endian properties
    - check property size
v2: - removed bogus check for negative property values
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

irq_chip->irq_mask/unmask are called with interrupts disabled and
irq_desc->lock held. So we cannot access i2c from this context. That's
what irq_bus_sync_unlock() is for.

Store the masked information in the chip data structure and update the
i2c bus from the irq_bus_sync_unlock() callback.

This does not need a while(pending) loop because the update to this is
always serialized via the bus lock, so we never have more than one pin
update pending.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Gregory Bean <gbean@codeaurora.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add a mutex to register communication and handling.  Without the mutex,
GPIOs didn't switch as expected when toggled in a fast sequence of
status changes of multiple outputs.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Latest kernel has many changes in IRQ subsystem and its interfaces, like
adding "irq_eoi" for struct irq_chip, this patch is a follow up change
for that.

Also remove the unnecessary cast for a "void *".
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit a1f5f22a ("gpio: timbgpio:
irq_data conversion") was slightly too enthusiastic in converting
timbgpio_irq() over to take an irq_data * argument instead of an
unsigned int irq argument, as it is a flow handler, which still take
IRQ numbers for now.  (And on top of that, it was using the wrong
accessors.)

This fixes it up, and seems to build without warnings.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/gpio/cs5535-gpio.c: In function 'cs5535_gpio_probe':
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'

Use vsprintf extension %pR to format resource.
Original-patch-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this
allows the modules to automatically be loaded when cs5535-mfd loads.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the gpio driver a lot.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

ML7213 is a companion chip for Intel Atom E6xx series.  This driver can be
used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.  This driver can access the IOH's GPIO
device.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kconfig dependency warning to satisfy dependencies:

warning: (GPIO_VX855 && GPIOLIB) selects MFD_VX855 which has unmet direct dependencies (MFD_SUPPORT && PCI)
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kconfig dependency warning to satisfy dependencies:

warning: (GPIO_RDC321X && PCI && GPIOLIB) selects MFD_RDC321X which has unmet direct dependencies (MFD_SUPPORT && PCI)
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Acked-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Cc: Gregory Bean <gbean@codeaurora.org>
Tested-by: NRohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Acked-by: NRabin Vincent <rabin.vincent@stericsson.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Acked-by: NMarc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Acked-by: N"Hennerich, Michael" <Michael.Hennerich@analog.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds (well, re-adds actually) handling for events/IRQs through cs5535
GPIOs.  In the wild and wooly world of CS5535, setup_event() is for
assigning an IRQ to a GPIO filter/event pair, and set_irq() sets up the
pair to trigger IRQs.

These should really only be used in highly platform-specific drivers (such
as OLPC's DCON driver).  Sadly, because set_irq() uses MSRs, this causes
the driver to become X86-specific.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic.  This
changes it to the following behavior:

 - when setting GPIOs, ignore the higher order bits (they're for
   clearing, we don't need to care about them).

 - when clearing GPIOs, keep all the bits, but unset (via XOR) the
   lower order bit that negates the clear bit that we care about.  That
   is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
   currently in the register with 0x0400 (GPIO 26's SET bit), and then
   OR that with the GPIO 26's CLEAR bit.
Tested-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.

This means that read-modify-write doesn't actually work for it, so don't
apply the errata here.  If a negative edge status gets lost after
resume..  well, we tried our best!
Tested-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NEric Miao <eric.miao@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Rename the tc35892 core/gpio drivers to tc3589x to include
new variants in the same mfd core
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Rename the header file to include further variants within
the same mfd core driver
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:

 "Atomic write transactions to the atomic GPIO High Bank Feature Bit
  registers should only affect the bits selected [...]"

 "after Suspend, an atomic write transaction [...] will clear all
  non-selected bits of the accessed register."

In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).

The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Several of the GPIOs on the WM8994 are fixed function on the WM8958 so
error out if the user tries to request them with gpiolib.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This is needed for supporting the upcoming VX855 camera and OLPC DCON
drivers, as well as the advanced viafb features on non-OLPC hardware
based on this chip.

Based on earlier work by Harald Welte.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Free allocated memory.  Call stmpe_disable() if it was enabled.
Signed-off-by: NVasiliy Kulikov <segooon@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch removes the requirement that gpio base be supplied in
platform data.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>