- 23 1月, 2013 6 次提交
-
-
由 Douglas Gilbert 提交于
Concerning pinctrl_macb0_rmii_mii, values were okay, but not comments. Signed-off-by: NDouglas Gilbert <dgilbert@interlog.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Boris BREZILLON 提交于
This patch overrides default macb pinctrl config defined in at91sam9260.dtsi (pinctrl_macb_rmii) with kizbox board config (pinctrl_macb_rmii + pinctrl_macb_rmii_mii_alt). Signed-off-by: NBoris BREZILLON <linux-arm@overkiz.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Joachim Eastwood 提交于
Signed-off-by: NJoachim Eastwood <manabian@gmail.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Richard Genoud 提交于
The SCK pins where missing in usarts pinctrl. Signed-off-by: NRichard Genoud <richard.genoud@gmail.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Richard Genoud 提交于
The PIN_BANK 3 is for PDxx pins, not PCxx pins. And PIN_BANK 1 is for PBxx, not PIN_BANK 0. Signed-off-by: NRichard Genoud <richard.genoud@gmail.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Sebastian Hesselbarth 提交于
The gpio controller on kirkwood can provide interrupts but is missing the #interrupt-cells property. This patch just adds it to both gpio controllers. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 17 1月, 2013 2 次提交
-
-
由 Alim Akhtar 提交于
As per the current exynos-dw-mshc bindings, dw-mshc-sdr-timing and dw-mshc-ddr-timing properties are having only two cells, these properties are wrongly set for exynos5250 based cros5250 and smdk5250 platfroms. This patch corrects above timing propreties for above platfroms Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com> Tested-by: NDoug Anderson <dianders@chromium.org> Acked-by: NDoug Anderson <dianders@chromium.org> Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
-
由 Maxime Ripard 提交于
The UART controller used in the A10/A13 is the Synopsys DesignWare 8250. The wrong use of a regular 8250 driver may lead to a oops during kernel boot with "irq 17: nobody cared", because the apb UART as an extra interrupt that gets raised when writing to the LCR when busy. Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 14 1月, 2013 1 次提交
-
-
由 Stephen Warren 提交于
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to $(targets) to prevent *.dtb from always being rebuilt. This fixes a regression introduced by the .dtb rule rework in 499cd829 "ARM: dt: change .dtb build rules to build in dts directory". Reported-by: NShawn Guo <shawn.guo@linaro.org> Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
- 12 1月, 2013 1 次提交
-
-
由 Bo Shen 提交于
Add pinctrl support for SSC on AT91 dtsi files. Signed-off-by: NBo Shen <voice.shen@atmel.com> [nicolas.ferre@atmel.com: split dtsi and driver changes] Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Reluctantly-acked-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
-
- 11 1月, 2013 1 次提交
-
-
由 Gregory CLEMENT 提交于
Actually the Armada 370 DB (aka DB-88F6710-BP-DDR3) come with 1GB and not 512MB. Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 10 1月, 2013 2 次提交
-
-
由 Sebastian Hesselbarth 提交于
Card detect for sdhci on Cubox is connected to the wrong pin (sdio1_cd instead of sdio0_cd). With support for cd-gpios and pinctrl add the corresponding properties to DT for Cubox. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Simon Guinot 提交于
Note that the pinctrl conversion also fixes GPIO support for ns2 boards. Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies on the pinctrl driver, then a pinctrl definition must be given to allow the GPIO configuration. Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 08 1月, 2013 5 次提交
-
-
由 Thomas Petazzoni 提交于
The Armada XP GPIO controller has two ways of notifying interrupts: using global interrupts or using per-CPU interrupts. In an attempt to use the best available features, the 'marvell,armadaxp-gpio' compatible string selects a variant of the gpio-mvebu driver that makes use of the per-CPU interrupts. Unfortunately, this doesn't work properly in a SMP context, because we fall into cases where the GPIO interrupt is enabled on CPU X at the GPIO controller level, but on CPU Y at the interrupt controller level. It is not yet clear how to fix that easily. So for 3.8, our approach is to switch to global interrupts for GPIOs, so that we do not fall into this per-CPU interrupts problem. This patch therefore fixes GPIO interrupts on Armada XP platforms. Without this patch, GPIO interrupts simply do not work reliably, because their proper operation depends on which CPU the code requesting the interrupt is running. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Rob Herring 提交于
With the addition of commit a0ae0240 (ARM: kernel: add device tree init map function), the cpu reg values must match the cpu mpidr register or we'll get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg value needs to be 0x90n to quiet the warnings. Signed-off-by: NRob Herring <rob.herring@calxeda.com> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Rob Herring 提交于
While device_type is considered deprecated, it is still needed for tools like lshw to identify cpu nodes. Signed-off-by: NRob Herring <rob.herring@calxeda.com> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Marek Vasut 提交于
The second FlexCAN port uses different clock than the first one, configure correct clock to prevent hanging of the system during bringing up of the port. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Sebastian Hesselbarth 提交于
During merge of the mvebu patches a clock gate for pinctrl was lost. This patch just readds the clock gate. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 07 1月, 2013 7 次提交
-
-
由 Andrew Lunn 提交于
The Armada XP MV78230 DT include file is missing a ; at the end of the cpu node. Reported-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
We originally thought that the MV78230 variant of the Armada XP had four Ethernet interfaces, like the other variants MV78260 and MV78460. In fact, this is not true, and the MV78230 has only three Ethernet interfaces. So, the definitions of the Ethernet interfaces is now done as follows: * armada-370-xp.dtsi: definitions of the first two interfaces, that are common to Armada 370 and Armada XP * armada-xp.dtsi: definition of the third interface, common to all Armada XP variants. * armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of the fourth interface. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
Contrary to our understanding at the time armada-xp-mv78230.dtsi was written, the MV78230 variant of the Armada XP SoC has two cores and not one. This patch updates the .dtsi file to take into account this reality. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
With the change to a DT based pinctrl/gpio driver, using gpio API calls in board-*.c files no longer works, a dereferenced NULL pointer exception occurs instead. By converting the GPIO code into a fixed-regulator which gets probed later once pinctrl/gpio is available, we avoid the exception. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NStefan Peter <s.peter@mplch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Nobuhiro Iwamatsu 提交于
Clock Management of kirkwood has moved to DT clock providers. However, TWSI1 has not yet been done. This switches TWSI1 of 88f6282 to DT clock providers. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Without the clock being held by a driver, it gets turned off at a bad time causing the SoC to lockup. This is often during reboot. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NStefan Peter <s.peter@mpl.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Gregory CLEMENT 提交于
The UART controller used in the Armada 370 and Armada XP SoCs is the Synopsys DesignWare 8250 (aka Synopsys DesignWare ABP UART). The improper use of the ns16550 can lead to a kernel oops during boot if a character is sent to the UART before the initialization of the driver. The DW APB has an extra interrupt that gets raised when writing to the LCR when busy. This explains why we need to use dw-apb-uart driver to handle this. Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 04 1月, 2013 1 次提交
-
-
由 Fabio Estevam 提交于
In the compatible field we should point the manufacturer of the board, which in this case is Buglabs. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 02 1月, 2013 1 次提交
-
-
由 Aaro Koskinen 提交于
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to probe when booting with DT. Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
- 29 12月, 2012 2 次提交
-
-
由 Kukjin Kim 提交于
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
-
由 Kukjin Kim 提交于
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
-
- 28 12月, 2012 1 次提交
-
-
由 Sean Paul 提交于
Reduce the HDMI resource size from 0x100000 to 0x70000 so it doesn't overlap the Displayport resource space. HDMI: (0x14530000 - 0x145A0000) DP: (0x145B0000 - 0x145B1000) Signed-off-by: NSean Paul <seanpaul@chromium.org> Signed-off-by: NPrathyush K <prathyush.k@samsung.com> Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
-
- 26 12月, 2012 1 次提交
-
-
由 Fabio Baltieri 提交于
Current nmk_pinctrl driver is not PRCMU dependent anymore, so it needs its own DT address resources to work properly, as done for platform_device in: f4828336 ARM: ux500: add PRCM register base for pinctrl Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org> Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
-
- 25 12月, 2012 1 次提交
-
-
由 Fabio Estevam 提交于
On the imx23-olinuxino board GPIO2_1 is connected to the LED and GPIO0_17 is the USB PHY reset. So make the IOMUX assignment properly. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 22 12月, 2012 1 次提交
-
-
由 Kukjin Kim 提交于
Commit db5b0ae0 ("Merge tag 'dt' of git://git.kernel.org/.../arm-soc") causes a duplicated build target. This patch fixes it and sorts out the build target alphabetically so that we can recognize something wrong easily. Cc: Olof Johansson <olof@lixom.net> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: NKukjin Kim <kgene.kim@samsung.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 21 12月, 2012 1 次提交
-
-
由 Olof Johansson 提交于
This is the rename portion of "ARM: sunxi: Change device tree naming scheme for sunxi" that were missed when the patch was applied. Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 18 12月, 2012 1 次提交
-
-
由 Maxime Ripard 提交于
There is several different SoCs sharing the sun5i codename: A10s, A12 and A13. Since there is enough differences to not consider those the same SoCs, change a bit the naming scheme to reflect this. Moreover, some boards like the olinuxino come in A10s and A13 variants, which also share the same SoC codename. So change the naming scheme to reflect both the codename and the market name of the SoCs used in the dtsi and in the board files Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 17 12月, 2012 1 次提交
-
-
由 Fabio Estevam 提交于
FEC controller is connected to AIPI2 bus. Also fix the AIPI1 address range. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 16 12月, 2012 1 次提交
-
-
由 Shawn Guo 提交于
Commit 91a9fec0 (ARM: move debug macros to common location) moves arch/arm/kernel/debug.S and arch/arm/kernel/head.S to CONFIG_DEBUG_LL_INCLUDE, but leaves arch/arm/boot/compressed/head.S still with mach/debug-macro.S. This causes the following build error on platforms that moved to new DEBUG_LL inclusion mechanism, when arch/arm/boot/compressed/head.S is compiled with DEBUG turned on. AS arch/arm/boot/compressed/head.o arch/arm/boot/compressed/head.S:49:30: fatal error: mach/debug-macro.S: No such file or directory compilation terminated. Fix the problem by replacing mach/debug-macro.S inclusion with CONFIG_DEBUG_LL_INCLUDE one. Reported-by: NSteev Klimaszewski <steev@genesi-usa.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 15 12月, 2012 3 次提交
-
-
由 Bo Shen 提交于
Change the value of status to disabled to keep the consistent Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
-
由 Jon Hunter 提交于
Commit 0d9250c4 (ARM: dts: omap4-panda: Add pinmux configuration for HDMI) added a new device-tree source file for Rev A4 of the OMAP4430 Panda board but it did not add this version to the makefile. Hence, add this file to the makefile. Signed-off-by: NJon Hunter <jon-hunter@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Jon Hunter 提交于
The system memory node for the OMAP2420 H4 was incorrectly defined as start address followed by end address, instead of start address and size. No noticable side-effects were observed but fix this for correctness. Signed-off-by: NJon Hunter <jon-hunter@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-