Do not use the dst cached neigh, we'll be getting rid of that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce IFF_LIVE_ADDR_CHANGE priv_flag and use it to disable
netif_running() check in eth_mac_addr()
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a hook in the binding path of netlink.

This is used by ctnetlink to allow module autoloading for the case
in which one user executes:

 conntrack -E

So far, this resulted in nfnetlink loaded, but not
nf_conntrack_netlink.

I have received in the past many complains on this behaviour.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following structure:

struct netlink_kernel_cfg {
        unsigned int    groups;
        void            (*input)(struct sk_buff *skb);
        struct mutex    *cb_mutex;
};

That can be passed to netlink_kernel_create to set optional configurations
for netlink kernel sockets.

I've populated this structure by looking for NULL and zero parameters at the
existing code. The remaining parameters that always need to be set are still
left in the original interface.

That includes optional parameters for the netlink socket creation. This allows
easy extensibility of this interface in the future.

This patch also adapts all callers to use this new interface.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If rpfilter is off (or the SKB has an IPSEC path) and there are not
tclassid users, we don't have to do anything at all when
fib_validate_source() is invoked besides setting the itag to zero.

We monitor tclassid uses with a counter (modified only under RTNL and
marked __read_mostly) and we protect the fib_validate_source() real
work with a test against this counter and whether rpfilter is to be
done.

Having a way to know whether we need no tclassid processing or not
also opens the door for future optimized rpfilter algorithms that do
not perform full FIB lookups.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At Facebook, we do Layer-3 DSR via IP-in-IP tunneling. Our load balancers wrap
an extra IP header on incoming packets so they can be routed to the backend.
In the v4 tunnel driver, when these packets fall on the default tunl0 device,
the behavior is to decapsulate them and drop them back on the stack. So our
setup is that tunl0 has the VIP and eth0 has (obviously) the backend's real
address.

In IPv6 we do the same thing, but the v6 tunnel driver didn't have this same
behavior - if you didn't have an explicit tunnel setup, it would drop the
packet.

This patch brings that v4 feature to the v6 driver.

The same IPv6 address checks are performed as with any normal tunnel,
but as the fallback tunnel endpoint addresses are unspecified, the checks
must be performed on a per-packet basis, rather than at tunnel
configuration time.

[Patch description modified by phil@ipom.com]
Signed-off-by: NVille Nuorvala <ville.nuorvala@gmail.com>
Tested-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checking for in_dev being NULL is pointless.

In fact, all of our callers have in_dev precomputed already,
so just pass it in and remove the NULL checking.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using NLMSG_GOODSIZE results in multiple pages being used as
nlmsg_new() will automatically add the size of the netlink
header to the payload thus exceeding the page limit.

NLMSG_DEFAULT_SIZE takes this into account.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit changes inet_csk_route_req() so that it uses a pointer to
a struct flowi6, rather than allocating its own on the stack. This
brings its behavior in line with its IPv4 cousin,
inet_csk_route_req(), and allows a follow-on patch to fix a dst leak.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The specific destination is the host we direct unicast replies to.
Usually this is the original packet source address, but if we are
responding to a multicast or broadcast packet we have to use something
different.

Specifically we must use the source address we would use if we were to
send a packet to the unicast source of the original packet.

The routing cache precomputes this value, but we want to remove that
precomputation because it creates a hard dependency on the expensive
rpfilter source address validation which we'd like to make cheaper.

There are only three places where this matters:

1) ICMP replies.

2) pktinfo CMSG

3) IP options

Now there will be no real users of rt->rt_spec_dst and we can simply
remove it altogether.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename it to ip_send_unicast_reply() and add explicit 'saddr'
argument.

This removed one of the few users of rt->rt_spec_dst.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's completely unnecessary.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a fixed value of "-1" or "-EMSGSIZE", propagate what
the nla_*() interfaces actually return.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.

PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access.  Both of these require
adjustments to the PHY driver to device matching code.

If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices.  If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS.  Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag.  Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.

get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false.  The follow-on patch to of_mdio.c will pass true where
appropriate.

EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit c074da28.

This change has several unwanted side effects:

1) Sockets will cache the DST_NOCACHE route in sk->sk_rx_dst and we'll
   thus never create a real cached route.

2) All TCP traffic will use DST_NOCACHE and never use the routing
   cache at all.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. removed code replication for tov calculation for 1G, 10G and
made is common for speed > 1G (1G, 10G, 40G, 100G).
2. defines values for #4 different 40G Phys (KR4, LF4, SR4, CR4)
Signed-off-by: NParav Pandit <parav.pandit@emulex.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removes all RTA_GET*() and RTA_PUT*() variations, as well as the
the unused rtattr_strcmp(). Get rid of rtm_get_table() by moving
it to its only user decnet.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DDOS synflood attacks hit badly IP route cache.

On typical machines, this cache is allowed to hold up to 8 Millions dst
entries, 256 bytes for each, for a total of 2GB of memory.

rt_garbage_collect() triggers and tries to cleanup things.

Eventually route cache is disabled but machine is under fire and might
OOM and crash.

This patch exploits the new TCP early demux, to set a nocache
boolean in case incoming TCP frame is for a not yet ESTABLISHED or
TIMEWAIT socket.

This 'nocache' boolean is then used in case dst entry is not found in
route cache, to create an unhashed dst entry (DST_NOCACHE)

SYN-cookie-ACK sent use a similar mechanism (ipv4: tcp: dont cache
output dst for syncookies), so after this patch, a machine is able to
absorb a DDOS synflood attack without polluting its IP route cache.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No longer used and a poor interface as they were macros
with embedded gotos.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.

This patch adds support for the Atmel RF230/231 radio transceivers.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every real 802.15.4 transceiver, which works with software MAC layer,
can be classified as a wpan device in this stack. So the wpan device
implementation provides missing link in datapath between the device
drivers and the Linux network queue.

According to the IEEE 802.15.4 standard each packet can be one of the
following types:
 - beacon
 - MAC layer command
 - ACK
 - data

This patch adds support for the data packet-type only, but this is
enough to perform data transmission and receiving over radio.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove use of module parameters on caif hsi device, as
rtnl configuration parameters are already supported.

All caif hsi configuration data is put in cfhsi_config,
and default values in hsi_default_config.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove use of struct platform_device, and replace it with
struct cfhsi_ops. Updated variable names in the same
spirit:
cfhsi_get_dev to cfhsi_get_ops,
cfhsi->dev to cfhsi->ops and,
cfhsi->dev.drv to cfhsi->ops->cb_ops.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RTNL support for managing the caif hsi interface.
The HSI HW interface is no longer registering as a device,
instead we use symbol_get to get hold of the HSI API.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing kernel doc for sk_rx_dst

Move sk_rx_dst to avoid two 32bit holes on 64bit arches
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With early demux enabled by default for TCP flows, there is high chance that
skb->sk will be non-null. 'unlikely()' was removed from __inet_lookup_skb() but
maybe it can be removed from skb_steal_sock() as well.

Note: skb_steal_sock() is also called by __inet6_lookup_skb() and
__udp4_lib_lookup_skb() but they are protected by their own 'unlikely' calls.
Signed-off-by: NVijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2603efa3 ("bug.h: Fix up powerpc build regression") corrected
the powerpc build case and extended the __ASSEMBLY__ guards, but it also
got caught in pre-processor hell accidentally matching the else case of
CONFIG_BUG resulting in the BUG disabled case tripping up on
-Werror=implicit-function-declaration.

It's not possible to __ASSEMBLY__ guard the entire file as architecture
code needs to get at the BUGFLAG_WARNING definition in the GENERIC_BUG
case, but the rest of the CONFIG_BUG=y/n case needs to be guarded.

Rather than littering endless __ASSEMBLY__ checks in each of the if/else
cases we just move the BUGFLAG definitions up under their own
GENERIC_BUG test and then shove everything else under one big
__ASSEMBLY__ guard.

Build tested on all of x86 CONFIG_BUG=y, CONFIG_BUG=n, powerpc (due to
it's dependence on BUGFLAG definitions in assembly code), and sh (due to
not bringing in linux/kernel.h to satisfy the taint flag definitions used
by the generic bug code).

Hopefully that's the end of the corner cases and I can abstain from ever
having to touch this infernal header ever again.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Tested-by: NFengguang Wu <wfg@linux.intel.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly.  They
report bogus sizes, in some cases becoming unusable as a result.

The bugs were triggered by commit
09b6b51b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices.  By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.

It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly.  Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.

Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device.  If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.

This fixes Bugzilla #43391.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't cache output dst for syncookies, as this adds pressure on IP route
cache and rcu subsystem for no gain.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is meant to add a control for disabling early socket demux.
The main motivation behind this patch is to provide an option to disable
the feature as it adds an additional cost to routing that reduces overall
throughput by up to 5%.  For example one of my systems went from 12.1Mpps
to 11.6 after the early socket demux was added.  It looks like the reason
for the regression is that we are now having to perform two lookups, first
the one for an established socket, and then the one for the routing table.

By adding this patch and toggling the value for ip_early_demux to 0 I am
able to get back to the 12.1Mpps I was previously seeing.

[ Move local variables in ip_rcv_finish() down into the basic
  block in which they are actually used.  -DaveM ]
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This comment is well out of date.
Signed-off-by: NDave Airlie <airlied@redhat.com>