pm_lock is taken twice while syncing HW TSF of p2p vif.
Fix this by taking the lock at caller side.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The keycache index is used to abort transmission for given station
when it goes to sleep state. But the commit "ath9k_hw: Abort transmission
for sleeping station" is not handling multi-key station. Fix that.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The data transmission to the power save station should be aborted
immediately, whenever the station informs sleep state. Right now
the frames queued into into hardware are being transmitted until
the hardware detects the power save station based excessive retries
of the data frames due to unacknowlegdement. Then remaining frames
are returned with filetered status and might be retried later by
driver or mac80211.

Per WFA certification testing, AP should not send out more than two
frames after processing nullfunc with PM bit set from associated
station. To speed up tx filtering, the pending frames in hardware
queues for given station will be aborted immediately via tx filter
registers. This transmit filters can be ignored if the descriptor
is having invalid destination index or clear destination mask set.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

we will need it for ath9k_htc, may be other drivers too
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we can reuse this fucntion on ath9k_htc.
Now we will need to use common version last_rssi, so switch
it too.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_has_tx_pending’:
drivers/net/wireless/ath/ath9k/main.c:1869: warning: ‘npend’ may be used uninitialized in this function

Introduced by commit 10e23181 ("ath9k:
optimize ath9k_flush").
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Soon mac80211 will support multi-interface CSA so
using sc->csa_vif is not an option.

Instead just depend on vif->csa_active. Calling
ieee80211_csa_finish() multiple number of times
should not be an issue.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Process GTT interrupts" accidentally
had a line that was commented out.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.

Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).

This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also, rename node_stat to node_aggr.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize "sync_cause" to zero since commit
"ath9k: move ath9k_debug_sync_cause out of ath9k_hw"
fills it conditionally based on ISR status.
Not doing this results in garbage values in debugfs.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IRQ save/restore is not required for the cycle counters
since they are accessed only from softirq and process context.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the BB processing code to the tasklet and avoid
doing it in the ISR, there is no real benefit and this
makes the ISR less heavy.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the convoluted and hacky method of
monitoring for connectivity. We rely on mac80211's connection
loss logic and doing it in the driver is not necessary.

The HW check for MAC/BB hangs is also simplified, there
is no need to have a separate work instance for it.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do a HW reset only for required signatures.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program the required baseband watchdog interrupt
mask to ensure that the correct watchdog interrupts
are raised when the BB is hung for some reason.

Also, use the capability HW_BB_WATCHDOG instead of
relying on other flags.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The maximum A-MPDU size is calculated in ath_tx_aggr_start(),
so there is no need to do it in node_attach() too. Also, make
sure that the correct size is calculated as described in
8.4.2.58.3.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make that function and ath9k_allow_beacon_config static
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw should not depend on any ath9k data structures like ath_softc
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The beacon code previously reset TSF on every configuration call, as
some of the code was not prepared to properly calculate nexttbtt based
on current TSF.

This patch adds a common function for calculating nexttbtt and moves the
TSF reset to driver start.

This should improve AP mode compatibility with various stations that
expect the TSF to not randomly jump due to hardware resets.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- Use generic bitops instead of custom hackery
- Move interrupt enable/disable logic from ath9k to ath9k_hw
- Decouple ISR call from btcoex
- Make the overflow callback optional (to prevent IRQ storms)
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pick the MAC address of the first virtual interface as the new hardware MAC
address. Set BSSID mask according to this MAC address. This fixes CVE-2013-4579.
Signed-off-by: NMathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of checking the queues in a loop with hardcoded sleep times
inbetween, use a wait queue to trigger queue checks after the tx
processing tasklet has run.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.

This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.

Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.

Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.

In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:

http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates

Example usage:

iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up

iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4

echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1  > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Preparation for adding the scanning state machine to ath9k
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework its wrapper function to make it more generic, using it as a
replacement for previous calls to ath9k_cmn_update_ichannel.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, if queues are full during a scan, tx scheduling does not
resume after switching back to the home channel.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PLL hang workaround is required only for AR9330 and
AR9340. This issue was first observed on an AP121 and the WAR
is enabled for AR9340 also (DB120 etc.), since it uses a PLL
design identical to AR9330. This is not required for AR9485 and AR9550.

Various bugs have been reported regarding this:

https://bugzilla.redhat.com/show_bug.cgi?id=997217
https://bugzilla.redhat.com/show_bug.cgi?id=994648

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CSA is only enabled for one interface, but the same limitation applies
for mac80211 too. It checks whether the beacon has been sent (different
approaches for non-EDMA-enabled and EDMA-enabled devices), and completes
the channel switch after that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To enable support for 5/10 MHz, some internal functions must be
converted from using the (old) channel_type to chandef. This is a good
chance to change all remaining occurences.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>