1. Handle the the thermal state directly in the work handler.
Remove the state selection function since nothing else uses it now.
2. On some asics there is no thermal state, so we just use a regular
state and force the low performance state.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use the UVD handle information to determine which
which power states to select when using UVD.  For
example, decoding a single SD stream requires much
lower clocks than multiple HD streams.

v2: switch to a cleaner dpm/uvd interface
v3: change the uvd power state while streams
are active if need be
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The smc ucode is required for dpm (dynamic power
management), but if it's missing just skip dpm setup
and don't disable acceleration.

Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=67876Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The rlc is required for dpm to work properly, so if
the rlc ucode is missing, don't enable dpm.  Enabling
dpm without the rlc enabled can result in hangs.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If the vblank time is too short to adjust mclk,
assume multiple displays (no mclk adjustments).
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Looks like a remnant from an old rebase.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows you to force specific power levels within a power
state.  Due to hardware restrictions between generations, the
interface is limited to the following 3 selections:

auto: all levels enabled
low: forced to the lowest power level
high: forced to the highest power level
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Certain older rv770 asics have both a performance and
a 3D performance state rather than just multiple performance
levels in the state power state.  The current code would
select the performance state rather than the 3D performance
state when the "performance" profile was selected.  This change
switches to the "balanced" profile by default which ends up being
the internal performance profile.  When the user selects the
"performance" profile, it selects the internal 3D performance
state so the user can select the higher performance modes.

For most asics this changes nothing.  For certain rv770 asics
with static performance and 3D performance states, this allows
you to select between then using by selecting the "balanced"
and "performance" dpm profiles.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix patching of vddc values for SI and enable manually forcing
clocks to default levels as per NI.

This improves the out of the box performance with SI asics.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For chips without debugfs dpm support say that it's not
implemented rather than not supported to avoid confusion
about DPM support in general.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This lays the frameworks to report realtime power level
feedback.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds dpm support for SI asics.  This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling

Set radeon.dpm=1 to enable.

v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Now that the proper fix has been implemented I can
remove the last remnants of the initial implementation.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Needed to properly handle dynamic state adjustment.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds dpm support for cayman asics.  This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)
- power containment
- shader power scaling

Set radeon.dpm=1 to enable.

v2: fold in tdp fix
v3: fix indentation
v4: fix 64 bit div
v5: attempt to fix state enable
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>

Use a dedicated copy of the current power state since
we may have to adjust it on the fly.

v2: fix up redundant state sets
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use a dedicated copy of the current power state since
we may have to adjust it on the fly.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Driver needs this information to validate power states.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When using UVD, the driver must switch to a special UVD power
state.  In the CS ioctl, switch to the power state and schedule
work to change the power state back, when the work comes up,
check if uvd is still busy and if not, switch back to the user
state, otherwise, reschedule the work.

Note:  We really need some better way to decide when to
switch out of the uvd power state.  Switching power states
while playback is active make uvd angry.

V2: fix locking.

V3: switch from timer to delayed work

V4: check fence driver for UVD jobs, reduce timeout to
    1 second and rearm timeout on activity

v5: rebase on new dpm tree

v6: rebase on interim uvd on demand changes

v7: fix UVD when DPM is disabled

v8: unify non-DPM and DPM UVD handling

v9: remove leftover idle work struct
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <deathsimple@vodafone.de>

This adds dpm support for trinity asics.  This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling

set radeon.dpm=1 to enable it.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds dpm support for sumo asics.  This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling

set radeon.dpm=1 to enable it.

v2: fix indention
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>

This adds dpm support for btc asics.  This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)

Set radeon.dpm=1 to enable.

v2: reduce stack usage
v3: attempt to fix state enable
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds dpm support for evergreen asics.  This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)

Set radeon.dpm=1 to enable.

v2: reduce stack usage, rename ulv struct
v3: fix thermal interrupt check notices by Jerome
v4: fix state enable
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds dpm support for rv7xx asics.  This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching

Set radeon.dpm=1 to enable.

v2: reduce stack usage
v3: fix 64 bit div
v4: fix state enable
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds dpm support for rv6xx asics.  This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching

Set radeon.dpm=1 to enable.

v2: remove duplicate line
v3: fix thermal interrupt check noticed by Jerome
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

This adds dpm support for rs780/rs880 asics.  This includes:
- clockgating
- dynamic engine clock scaling
- dynamic voltage scaling

set radeon.dpm=1 to enable it.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds the common dpm (dynamic power management)
infrastructure:
- dpm callbacks
- dpm init/fini/suspend/resume
- dpm power state selection

No device specific code is enabled yet.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It doesn't work reliably.  Just report back the currently
selected engine clock.

Partially fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62493Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

vddci needs to track mclk for multi-head.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

radeon_fence_wait_empty_locked should not trigger GPU reset as no
place where it's call from would benefit from such thing and it
actually lead to a kernel deadlock in case the reset is triggered
from pm codepath. Instead force ring completion in place where it
makes sense or return early in others.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Starting on BTC, there are no longer separate states for
single head and multi-head, we just use the high mclk/voltage
for all states for multi-head.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=49981

v2: fix typo
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Driver used to print "default" as the state type regardless
of whether it is the default state.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

SI asics store voltage information differently so we
don't have a way to deal with it properly yet.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Move it out of the radeon_pm.c and into radeon_acpi.c since
we use it for more than just pm now.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Set up an handler for ACPI events and respond to brightness change
requests from the system BIOS.
v2: fix notification when using device-specific command codes
(tested by Pali Rohár <pali.rohar@gmail.com>); cache the encoder
controlling the backlight during the initialization to avoid searching
it every time (suggested by Alex Deucher).
v3: whitespace fixes (Alex Deucher).
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

1. Drop gui idle stuff, it's not as reliable as fences and only
covers the 3D engine.
2. Wait for fences on all rings.  This makes sure all rings are
idle when reclocking.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

1. It is really dangerous to have more than one
   spinlock protecting the same information.

2. radeon_irq_set sometimes wasn't called with lock
   protection, so it can happen that more than one
   CPU would tamper with the irq regs at the same
   time.

3. The pm.gui_idle variable was assuming that the 3D
   engine wasn't becoming idle between testing the
   register and setting the variable. So just remove
   it and test the register directly.

v2: Also handle the hpd irq code the same way.
v3: Rename hpd parameter for clarification.
Signed-off-by: NChristian Koenig <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

It is a rw_semaphore now and only write locked
while changing the clock. Also the lock is renamed
to better reflect what it is protecting.

v2: Keep the ttm_vm_ops on IGPs
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>