exynos5250-cros-common.dtsi was meant for sharing common pieces across
ChromeOS devices. This turned out premature, as several devices ended up
in the common file that are not common after all. Since the remaining
common ChromeOS pieces are fairly minor,  exynos5250-cros-common.dtsi
was requested to be merged into the Snow device tree, sharing only the
keyboard controller for now. This may be re-evaluated as both mature.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The pinctrl properties should be on the device directly and not on the
slot sub-node.
Reported-by: NDoug Anderson <dianders@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.

sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NTomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.

This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NTomeu Vizoso <tomeu@tomeuvizoso.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Power efficiency improves on Baytrail (Intel Atom Processor E3000)
when Linux disables C6 auto-demotion.

Based on work by Srinidhi Kasagar <srinidhi.kasagar@intel.com>.
Signed-off-by: NLen Brown <len.brown@intel.com>
Cc: x86@kernel.org

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Perform a pci_claim_resource() on all valid resources discovered
during the OF device tree scan.

Based almost entirely upon the PCI OF bus probing code which does
the same thing there.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems that when a PCI Express bridge is not in use and has no devices
behind it, the ranges property is bogus.  Specifically the size property
is of the form [0xffffffff:...], and if you add this size to the resource
start address the 64-bit calculation will overflow.

Just check specifically for this size value signature and skip them.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dump the various aspects of the PCI bridge probed at boot time, most
importantly the bridge number ranges, and the ranges property.

This helps diagnose PCI resource issues and other problems by giving
ofpci_debug=1 on the boot command line.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tracepoint to track hugepage invalidate. This help us
in debugging difficult to track bugs.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On ppc64 we support 4K hash pte with 64K page size. That requires
us to track the hash pte slot information on a per 4k basis. We do that
by storing the slot details in the second half of pte page. The pte bit
_PAGE_COMBO is used to indicate whether the second half need to be
looked while building real_pte. We need to use read memory barrier while
doing that so that load of hidx is not reordered w.r.t _PAGE_COMBO
check. On the store side we already do a lwsync in __hash_page_4K

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We would get wrong results in compiler recomputed old_pmd. Avoid
that by using ACCESS_ONCE

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As per ISA, for 4k base page size we compare 14..65 bits of VA specified
with the entry_VA in tlb. That implies we need to make sure we do a
tlbie with all the possible 4k va we used to access the 16MB hugepage.
With 64k base page size we compare 14..57 bits of VA. Hence we cannot
ignore the lower 24 bits of va while tlbie .We also cannot tlb
invalidate a 16MB entry with just one tlbie instruction because
we don't track which va was used to instantiate the tlb entry.

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault for
these pages.

We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.

Use _PAGE_COMBO to determine the page size with which we should
invalidate the hash table entries on unmap.

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault
for these pages.

We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.

Handle this correctly for 16M pages

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The segment identifier and segment size will remain the same in
the loop, So we can compute it outside. We also change the
hugepage_invalidate interface so that we can use it the later patch

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With hugepages, we store the hpte valid information in the pte page
whose address is stored in the second half of the PMD. Use a
write barrier to make sure clearing pmd busy bit and updating
hpte valid info are ordered properly.

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There is an issue currently where NUMA information is used on powerpc
(and possibly ia64) before it has been read from the device-tree, which
leads to large slab consumption with CONFIG_SLUB and memoryless nodes.

NUMA powerpc non-boot CPU's cpu_to_node/cpu_to_mem is only accurate
after start_secondary(), similar to ia64, which is invoked via
smp_init().

Commit 6ee0578b ("workqueue: mark init_workqueues() as
early_initcall()") made init_workqueues() be invoked via
do_pre_smp_initcalls(), which is obviously before the secondary
processors are online.

Additionally, the following commits changed init_workqueues() to use
cpu_to_node to determine the node to use for kthread_create_on_node:

bce90380 ("workqueue: add wq_numa_tbl_len and
wq_numa_possible_cpumask[]")
f3f90ad4 ("workqueue: determine NUMA node of workers accourding to
the allowed cpumask")

Therefore, when init_workqueues() runs, it sees all CPUs as being on
Node 0. On LPARs or KVM guests where Node 0 is memoryless, this leads to
a high number of slab deactivations
(http://www.spinics.net/lists/linux-mm/msg67489.html).

Fix this by initializing the powerpc-specific CPU<->node/local memory
node mapping as early as possible, which on powerpc is
do_init_bootmem(). Currently that function initializes the mapping for
the boot CPU, but we extend it to setup the mapping for all possible
CPUs. Then, in smp_prepare_cpus(), we can correspondingly set the
per-cpu values for all possible CPUs. That ensures that before the
early_initcalls run (and really as early as possible), the per-cpu NUMA
mapping is accurate.

While testing memoryless nodes on PowerKVM guests with a fix to the
workqueue logic to use cpu_to_mem() instead of cpu_to_node(), with a
guest topology of:

available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus: 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
node 1 size: 16336 MB
node 1 free: 15329 MB
node distances:
node   0   1
  0:  10  40
  1:  40  10

the slab consumption decreases from

Slab:             932416 kB
SUnreclaim:       902336 kB

to

Slab:             395264 kB
SUnreclaim:       359424 kB

And we a corresponding increase in the slab efficiency from

slab                                   mem     objs    slabs
                                      used   active   active
------------------------------------------------------------
kmalloc-16384                       337 MB   11.28%  100.00%
task_struct                         288 MB    9.93%  100.00%

to

slab                                   mem     objs    slabs
                                      used   active   active
------------------------------------------------------------
kmalloc-16384                        37 MB  100.00%  100.00%
task_struct                          31 MB  100.00%  100.00%

Powerpc didn't support memoryless nodes until recently (64bb80d8
"powerpc/numa: Enable CONFIG_HAVE_MEMORYLESS_NODES" and 8c272261
"powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"). Those commits also
helped improve memory consumption with these kind of environments.
Signed-off-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Free memory allocated using kmem_cache_zalloc using kmem_cache_free
rather than kfree.

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@@
expression x,E,c;
@@

 x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
 ... when != x = E
     when != &x
?-kfree(x)
+kmem_cache_free(c,x)
// </smpl>
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

A buffer returned by H_VTERM_PARTNER_INFO contains device information
in big endian format, causing problems for little endian architectures.
This patch ensures that they are in cpu endian.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

xmon only soft disables interrupts. This seems like a bad idea - we
certainly don't want decrementer and PMU exceptions going off when
we are debugging something inside xmon.

This issue was uncovered when the hard lockup detector went off
inside xmon. To ensure we wont get a spurious hard lockup warning,
I also call touch_nmi_watchdog() when exiting xmon.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It appears that commits 7f06f21d ("powerpc/tm: Add checking to
treclaim/trechkpt") and e4e38121 ("KVM: PPC: Book3S HV: Add
transactional memory support") both added definitions of TEXASR_FS.
Remove one of them. At the same time, fix the alignment of the remaining
definition (should be tab-separated like the rest of the #defines).
Signed-off-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Function remove_ddw() could be called in of_reconfig_notifier and
we potentially remove the dynamic DMA window property, which invokes
of_reconfig_notifier again. Eventually, it leads to the deadlock as
following backtrace shows.

The patch fixes the above issue by deferring releasing the dynamic
DMA window property while releasing the device node.

=============================================
[ INFO: possible recursive locking detected ]
3.16.0+ #428 Tainted: G        W
---------------------------------------------
drmgr/2273 is trying to acquire lock:
 ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
 .__blocking_notifier_call_chain+0x40/0x78

but task is already holding lock:
 ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
 .__blocking_notifier_call_chain+0x40/0x78

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock((of_reconfig_chain).rwsem);
  lock((of_reconfig_chain).rwsem);
 *** DEADLOCK ***

 May be due to missing lock nesting notation

2 locks held by drmgr/2273:
 #0:  (sb_writers#4){.+.+.+}, at: [<c0000000001cbe70>] \
      .vfs_write+0xb0/0x1f8
 #1:  ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
      .__blocking_notifier_call_chain+0x40/0x78

stack backtrace:
CPU: 17 PID: 2273 Comm: drmgr Tainted: G        W     3.16.0+ #428
Call Trace:
[c0000000137e7000] [c000000000013d9c] .show_stack+0x88/0x148 (unreliable)
[c0000000137e70b0] [c00000000083cd34] .dump_stack+0x7c/0x9c
[c0000000137e7130] [c0000000000b8afc] .__lock_acquire+0x128c/0x1c68
[c0000000137e7280] [c0000000000b9a4c] .lock_acquire+0xe8/0x104
[c0000000137e7350] [c00000000083588c] .down_read+0x4c/0x90
[c0000000137e73e0] [c000000000091890] .__blocking_notifier_call_chain+0x40/0x78
[c0000000137e7490] [c000000000091900] .blocking_notifier_call_chain+0x38/0x48
[c0000000137e7520] [c000000000682a28] .of_reconfig_notify+0x34/0x5c
[c0000000137e75b0] [c000000000682a9c] .of_property_notify+0x4c/0x54
[c0000000137e7650] [c000000000682bf0] .of_remove_property+0x30/0xd4
[c0000000137e76f0] [c000000000052a44] .remove_ddw+0x144/0x168
[c0000000137e7790] [c000000000053204] .iommu_reconfig_notifier+0x30/0xe0
[c0000000137e7820] [c00000000009137c] .notifier_call_chain+0x6c/0xb4
[c0000000137e78c0] [c0000000000918ac] .__blocking_notifier_call_chain+0x5c/0x78
[c0000000137e7970] [c000000000091900] .blocking_notifier_call_chain+0x38/0x48
[c0000000137e7a00] [c000000000682a28] .of_reconfig_notify+0x34/0x5c
[c0000000137e7a90] [c000000000682e14] .of_detach_node+0x44/0x1fc
[c0000000137e7b40] [c0000000000518e4] .ofdt_write+0x3ac/0x688
[c0000000137e7c20] [c000000000238430] .proc_reg_write+0xb8/0xd4
[c0000000137e7cd0] [c0000000001cbeac] .vfs_write+0xec/0x1f8
[c0000000137e7d70] [c0000000001cc3b0] .SyS_write+0x58/0xa0
[c0000000137e7e30] [c00000000000a064] syscall_exit+0x0/0x98

Cc: stable@vger.kernel.org
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While running command "drmgr -c phb -r -s 'PHB 528'", following
backtrace jumped out because the target device node isn't marked
with OF_DETACHED by of_detach_node(), which caused by error
returned from memory hotplug related reconfig notifier when
disabling CONFIG_MEMORY_HOTREMOVE. The patch fixes it.

ERROR: Bad of_node_put() on /pci@800000020000210/ethernet@0
CPU: 14 PID: 2252 Comm: drmgr Tainted: G        W     3.16.0+ #427
Call Trace:
[c000000012a776a0] [c000000000013d9c] .show_stack+0x88/0x148 (unreliable)
[c000000012a77750] [c00000000083cd34] .dump_stack+0x7c/0x9c
[c000000012a777d0] [c0000000006807c4] .of_node_release+0x58/0xe0
[c000000012a77860] [c00000000038a7d0] .kobject_release+0x174/0x1b8
[c000000012a77900] [c00000000038a884] .kobject_put+0x70/0x78
[c000000012a77980] [c000000000681680] .of_node_put+0x28/0x34
[c000000012a77a00] [c000000000681ea8] .__of_get_next_child+0x64/0x70
[c000000012a77a90] [c000000000682138] .of_find_node_by_path+0x1b8/0x20c
[c000000012a77b40] [c000000000051840] .ofdt_write+0x308/0x688
[c000000012a77c20] [c000000000238430] .proc_reg_write+0xb8/0xd4
[c000000012a77cd0] [c0000000001cbeac] .vfs_write+0xec/0x1f8
[c000000012a77d70] [c0000000001cc3b0] .SyS_write+0x58/0xa0
[c000000012a77e30] [c00000000000a064] syscall_exit+0x0/0x98

Cc: stable@vger.kernel.org
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Avoids this warning:

arch/powerpc/boot/gunzip_util.c:118:9: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

PowerNV platform is capable of capturing host memory region when system
crashes (because of host/firmware). We have new OPAL API to register/
unregister memory region to be captured when system crashes.

This patch adds support for new API. Also during boot time we register
kernel log buffer and unregister before doing kexec.
Signed-off-by: NVasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We have been a bit slack about updating the CPU_FTRS_POSSIBLE and
CPU_FTRS_ALWAYS masks. When we added POWER8, and also POWER8E we forgot
to update the ALWAYS mask. And when we added POWER8_DD1 we forgot to
update both the POSSIBLE and ALWAYS masks.

Luckily this hasn't caused any actual bugs AFAICS. Failing to update the
ALWAYS mask just forgoes a potential optimisation opportunity. Failing
to update the POSSIBLE mask for POWER8_DD1 is also OK because it only
removes a bit rather than adding any.

Regardless they should all be in both masks so as to avoid any future
bugs when the set of ALWAYS/POSSIBLE bits changes, or the masks
themselves change.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NMichael Neuling <mikey@neuling.org>
Acked-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch disables the branch target address CAM which under specific
circumstances may cause the processor to skip execution of 1-4
instructions. This fixes IBM Erratum #47.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When we take full hotplug to recover from EEH errors, PCI buses
could be involved. For the case, the child devices of involved
PCI buses can't be attached to IOMMU group properly, which is
caused by commit 3f28c5af ("powerpc/powernv: Reduce multi-hit of
iommu_add_device()").

When adding the PCI devices of the newly created PCI buses to
the system, the IOMMU group is expected to be added in (C).
(A) fails to bind the IOMMU group because bus->is_added is
false. (B) fails because the device doesn't have binding IOMMU
table yet. bus->is_added is set to true at end of (C) and
pdev->is_added is set to true at (D).

   pcibios_add_pci_devices()
      pci_scan_bridge()
         pci_scan_child_bus()
            pci_scan_slot()
               pci_scan_single_device()
                  pci_scan_device()
                  pci_device_add()
                     pcibios_add_device()           A: Ignore
                     device_add()                   B: Ignore
                  pcibios_fixup_bus()
                     pcibios_setup_bus_devices()
                        pcibios_setup_device()      C: Hit
      pcibios_finish_adding_to_bus()
         pci_bus_add_devices()
            pci_bus_add_device()                    D: Add device

If the parent PCI bus isn't involved in hotplug, the IOMMU
group is expected to be bound in (B). (A) should fail as the
sysfs entries aren't populated.

The patch fixes the issue by reverting commit 3f28c5af and remove
WARN_ON() in iommu_add_device() to allow calling the function
even the specified device already has associated IOMMU group.

Cc: <stable@vger.kernel.org>  # 3.16+
Reported-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Similar to the previous commit which described why we need to add a
barrier to arch_spin_is_locked(), we have a similar problem with
spin_unlock_wait().

We need a barrier on entry to ensure any spinlock we have previously
taken is visibly locked prior to the load of lock->slock.

It's also not clear if spin_unlock_wait() is intended to have ACQUIRE
semantics. For now be conservative and add a barrier on exit to give it
ACQUIRE semantics.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The kernel defines the function spin_is_locked(), which can be used to
check if a spinlock is currently locked.

Using spin_is_locked() on a lock you don't hold is obviously racy. That
is, even though you may observe that the lock is unlocked, it may become
locked at any time.

There is (at least) one exception to that, which is if two locks are
used as a pair, and the holder of each checks the status of the other
before doing any update.

Assuming *A and *B are two locks, and *COUNTER is a shared non-atomic
value:

The first CPU does:

	spin_lock(*A)

	if spin_is_locked(*B)
		# nothing
	else
		smp_mb()
		LOAD r = *COUNTER
		r++
		STORE *COUNTER = r

	spin_unlock(*A)

And the second CPU does:

	spin_lock(*B)

	if spin_is_locked(*A)
		# nothing
	else
		smp_mb()
		LOAD r = *COUNTER
		r++
		STORE *COUNTER = r

	spin_unlock(*B)

Although this is a strange locking construct, it should work.

It seems to be understood, but not documented, that spin_is_locked() is
not a memory barrier, so in the examples above and below the caller
inserts its own memory barrier before acting on the result of
spin_is_locked().

For now we assume spin_is_locked() is implemented as below, and we break
it out in our examples:

	bool spin_is_locked(*LOCK) {
		LOAD l = *LOCK
		return l.locked
	}

Our intuition is that there should be no problem even if the two code
sequences run simultaneously such as:

	CPU 0			CPU 1
	==================================================
	spin_lock(*A)		spin_lock(*B)
	LOAD b = *B		LOAD a = *A
	if b.locked # true	if a.locked # true
	# nothing		# nothing
	spin_unlock(*A)		spin_unlock(*B)

If one CPU gets the lock before the other then it will do the update and
the other CPU will back off:

	CPU 0			CPU 1
	==================================================
	spin_lock(*A)
	LOAD b = *B
				spin_lock(*B)
	if b.locked # false	LOAD a = *A
	else			if a.locked # true
	smp_mb()		# nothing
	LOAD r1 = *COUNTER	spin_unlock(*B)
	r1++
	STORE *COUNTER = r1
	spin_unlock(*A)

However in reality spin_lock() itself is not indivisible. On powerpc we
implement it as a load-and-reserve and store-conditional.

Ignoring the retry logic for the lost reservation case, it boils down to:
	spin_lock(*LOCK) {
		LOAD l = *LOCK
		l.locked = true
		STORE *LOCK = l
		ACQUIRE_BARRIER
	}

The ACQUIRE_BARRIER is required to give spin_lock() ACQUIRE semantics as
defined in memory-barriers.txt:

     This acts as a one-way permeable barrier.  It guarantees that all
     memory operations after the ACQUIRE operation will appear to happen
     after the ACQUIRE operation with respect to the other components of
     the system.

On modern powerpc systems we use lwsync for ACQUIRE_BARRIER. lwsync is
also know as "lightweight sync", or "sync 1".

As described in Power ISA v2.07 section B.2.1.1, in this scenario the
lwsync is not the barrier itself. It instead causes the LOAD of *LOCK to
act as the barrier, preventing any loads or stores in the locked region
from occurring prior to the load of *LOCK.

Whether this behaviour is in accordance with the definition of ACQUIRE
semantics in memory-barriers.txt is open to discussion, we may switch to
a different barrier in future.

What this means in practice is that the following can occur:

	CPU 0			CPU 1
	==================================================
	LOAD a = *A 		LOAD b = *B
	a.locked = true		b.locked = true
	LOAD b = *B		LOAD a = *A
	STORE *A = a		STORE *B = b
	if b.locked # false	if a.locked # false
	else			else
	smp_mb()		smp_mb()
	LOAD r1 = *COUNTER	LOAD r2 = *COUNTER
	r1++			r2++
	STORE *COUNTER = r1
				STORE *COUNTER = r2	# Lost update
	spin_unlock(*A)		spin_unlock(*B)

That is, the load of *B can occur prior to the store that makes *A
visibly locked. And similarly for CPU 1. The result is both CPUs hold
their lock and believe the other lock is unlocked.

The easiest fix for this is to add a full memory barrier to the start of
spin_is_locked(), so adding to our previous definition would give us:

	bool spin_is_locked(*LOCK) {
		smp_mb()
		LOAD l = *LOCK
		return l.locked
	}

The new barrier orders the store to the lock we are locking vs the load
of the other lock:

	CPU 0			CPU 1
	==================================================
	LOAD a = *A 		LOAD b = *B
	a.locked = true		b.locked = true
	STORE *A = a		STORE *B = b
	smp_mb()		smp_mb()
	LOAD b = *B		LOAD a = *A
	if b.locked # true	if a.locked # true
	# nothing		# nothing
	spin_unlock(*A)		spin_unlock(*B)

Although the above example is theoretical, there is code similar to this
example in sem_lock() in ipc/sem.c. This commit in addition to the next
commit appears to be a fix for crashes we are seeing in that code where
we believe this race happens in practice.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Once again, we see

arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:865: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:866: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:890: Error: attempt to move .org backwards

when compiling ppc:allmodconfig.

This time the problem has been caused by to commit 0869b6fd
("powerpc/book3s: Add basic infrastructure to handle HMI in Linux"),
which adds functions hmi_exception_early and hmi_exception_after_realmode
into a critical (size-limited) code area, even though that does not appear
to be necessary.

Move those functions to a non-critical area of the file.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

__early_init_mmu() does some things that are really only needed by the
boot cpu.  On FSL booke, This includes calling
memblock_enforce_memory_limit(), which is labelled __init.  Secondary
cpu init code can't be __init as that would break CPU hotplug.

While it's probably a bug that memblock_enforce_memory_limit() isn't
__init_memblock instead, there's no reason why we should be doing this
stuff for secondary cpus in the first place.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Christopher reports that perf_event_print_debug() can crash in uniprocessor
builds.  The crash is due to pcr_ops being NULL.

This happens because pcr_arch_init() is only invoked by smp_cpus_done() which
only executes in SMP builds.

init_hw_perf_events() is closely intertwined with pcr_ops being setup properly,
therefore:

1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of
   from smp_cpus_done().

2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init().

3) Move init_hw_perf_events to a later initcall so that it we will be
   sure to invoke pcr_arch_init() after all cpus are brought up.

Finally, guard the one naked sequence of pcr_ops dereferences in
__global_pmu_self() with an appropriate NULL check.
Reported-by: NChristopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nmi_cpu_busy() is a SMP function call that just makes sure that all of the
cpus are spinning using cpu cycles while the NMI test runs.

It does not need to disable IRQs because we just care about NMIs executing
which will even with 'normal' IRQs disabled.

It is not legal to enable hard IRQs in a SMP cross call, in fact this bug
triggers the BUG check in irq_work_run_list():

	BUG_ON(!irqs_disabled());

Because now irq_work_run() is invoked from the tail of
generic_smp_call_function_single_interrupt().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds bindings for APM X-Gene SoC ethernet driver.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NRavi Patel <rapatel@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b7dd0e35 (x86/xen: safely map and unmap grant frames when
in atomic context) causes PVH guests to crash in
arch_gnttab_map_shared() when they attempted to map the pages for the
grant table.

This use of a PV-specific function during the PVH grant table setup is
non-obvious and not needed.  The standard vmap() function does the
right thing.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reported-by: NMukesh Rathor <mukesh.rathor@oracle.com>
Tested-by: NMukesh Rathor <mukesh.rathor@oracle.com>
Cc: stable@vger.kernel.org

If the timer irqs are resumed during device resume it is possible in
certain circumstances for the resume to hang early on, before device
interrupts are resumed.  For an Ubuntu 14.04 PVHVM guest this would
occur in ~0.5% of resume attempts.

It is not entirely clear what is occuring the point of the hang but I
think a task necessary for the resume calls schedule_timeout(),
waiting for a timer interrupt (which never arrives).  This failure may
require specific tasks to be running on the other VCPUs to trigger
(processes are not frozen during a suspend/resume if PREEMPT is
disabled).

Add IRQF_EARLY_RESUME to the timer interrupts so they are resumed in
syscore_resume().
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org

This was introduced in commit e306e3be (Merge tag
'stable/for-linus-3.17-rc0-tag').
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>