The first hunk of this patch got merged wrong, likely due to some
changes at the em28xx resume code. Revert it to reapply it right.

This reverts commit 37571b16.
Reported-by: NChris Lee <updatelee@gmail.com>
Reported-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: stable@vger.kernel.org # Don't apply this patch or 37571b16Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Pointer to device state has been moved to different location during
some change. PCTV 290e LNA function still uses old pointer, carried
over FE priv, and it crash.
Reported-by: NJanne Kujanpää <jikuja@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.

Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Simplify the logic a little by removing one level of identation.
Also, it only makes sense to print something if the .fini callback
is actually doing something.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We can't free struct em28xx while one of the extensions is still
using it.

So, add a kref() to control it, freeing it only after the
extensions fini calls.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.

Tested with both 8VSB and 256QAM modulations.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the Trident DRX-J driver, including a card profile for the
PCTV 80e which uses the chip.

Thanks to Trident for allowing the release of this code under a BSD license,
and of course Hauppauge/PCTV for pushing for its release to the community.

[pdickeybeta@gmail.com: modified to fix compilation errors and also to move
 the driver files from the drx39xy subdirectory to the frontends directory]

[m.chehab@samsung.com: fix merge conflicts, commented drx-j compilation and
 added EM28XX_R06_I2C_CLK setup also to the board setup]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That helps to understand what's going there.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Several URBs will be simply not filled. Don't call the DVB
core software filter for those empty URBs.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.

Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The current code assumes that the analog + digital video endpoints are always at
interface number 0 when changing the alternate setting.
This seems to work fine for most existing devices.
However, at least the SpeedLink VAD Laplace webcam has the video endpoint on
interface number 3 (which fortunately doesn't cause any trouble because ist uses
bulk transfers only).
We already consider the actual interface number for audio endpoints, so
rename the the audio_ifnum variable and use it for all device types.
Also get get rid of a pointless (ifnum < 0) in em28xx-audio.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The option to load firmware asynchronously were added due to
a requirement with a few versions of udev. It turns that this was
a bad idea and caused regressions on drxk-based devices.

So, we end by only letting the firmware to be loaded syncronously
everywhere.

So, let's remove the bad code.

This patch partially reverts the changeset 8e30783b.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That helps to identify if something fails and explain why em28xx
struct is not freed (if it ever happens).
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

[media] em28xx: move usb buffer pre-allocation and transfer uninit from the core to the dvb extension
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Now that em28xx can be compiled without V4L support, we should
call em28xx_setup_xc3028() on both em28xx-v4l and em28xx-dvb
modules.
Reported-by: NChris Lee <updatelee@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

A few devices (em2860) use a separate interface for audio only
Audio Vendor Class USB. That interface should not be used by
Remote Controller, Analog TV or Digital TV.

Prevents initializing all non-audio extensions for the audio
only interface.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Use the same module version on all em28xx sub-modules, and use
the same naming convention to describe the driver.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a message with consistent prints before and after each
extension initialization, and provide a better text for module
load.

While here, add a missing sanity check for extension finish
code at em28xx-v4l extension.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Device has following chips: Empia EM28178, Montage M88DS3103,
Montage M88TS2022, Allegro A8293.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds support for the UB435-Q V2. You might need to
use the device once with the Windows driver provided by KWorld
in order to permanently reprogram the device descriptors. Thanks
to Jarod Wilson for the initial attempt at adding support for this
device.

[m.chehab@samsung.com: Fixed Whitespace mangling, Coding Style and
 improved the error handling at DVB attach]
Signed-off-by: NJean-Francois Thibert <jfthibert@google.com>
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix CodingStyle on the GPIO init tables.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That version of DRX-K chip supports only 2.
drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
drxk: Warning -22 on qam_demodulator_command
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

tda18271c2dd => tda18271
tda18271 is more complete than tda18271c2dd.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Downloading new firmware for DRX-K demodulator is not obligatory but
usually it offers important bug fixes compared to default firmware
burned into chip rom. DRX-K demod driver will continue even without
the firmware, but in that case it will print warning to system log
to tip user he should install firmware.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

- add definition for GPIO register 0x09 (reading/input)
- extend the information the chip variants that support GPIO registers 0x08/0x09
- rename EM28XX_R08_GPIO to EM2820_R08_GPIO_CTRL
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The em25xx/em276x/7x/8x provides 4 GPIO register sets,
each of them consisting of separate read and a write registers.
The same registers are also used by the em2874/174/84.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: NJakob Haufe <sur5r@sur5r.net>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx is oopsing with some DVB devices:

[10856.061884] general protection fault: 0000 [#1] SMP
[10856.067041] Modules linked in: rc_hauppauge em28xx_rc xc5000 drxk em28xx_dvb dvb_core em28xx videobuf2_vmalloc videobuf2_memops videobuf2_core rc_pixelview_new tuner_xc2028 tuner cx8800 cx88xx tveeprom btcx_risc videobuf_dma_sg videobuf_core rc_core v4l2_common videodev ebtable_nat ebtables nf_conntrack_ipv4 nf_defrag_ipv4 xt_CHECKSUM be2iscsi iscsi_boot_sysfs iptable_mangle bnx2i cnic uio cxgb4i cxgb4 tun bridge cxgb3i cxgb3 stp ip6t_REJECT mdio libcxgbi nf_conntrack_ipv6 llc nf_defrag_ipv6 ib_iser rdma_cm ib_addr xt_conntrack iw_cm ib_cm ib_sa nf_conntrack ib_mad ib_core bnep bluetooth iscsi_tcp libiscsi_tcp ip6table_filter libiscsi ip6_tables scsi_transport_iscsi xfs libcrc32c snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm tg3 snd_page_alloc snd_timer
[10856.139176]  snd ptp iTCO_wdt soundcore pps_core iTCO_vendor_support lpc_ich mfd_core coretemp nfsd hp_wmi crc32c_intel microcode serio_raw rfkill sparse_keymap nfs_acl lockd sunrpc kvm_intel kvm uinput binfmt_misc firewire_ohci nouveau mxm_wmi i2c_algo_bit drm_kms_helper firewire_core crc_itu_t ttm drm i2c_core wmi [last unloaded: dib0070]
[10856.168969] CPU 1
[10856.170799] Pid: 13606, comm: dvbv5-zap Not tainted 3.9.0-rc5+ #26 Hewlett-Packard HP Z400 Workstation/0AE4h
[10856.181187] RIP: 0010:[<ffffffffa0459e47>]  [<ffffffffa0459e47>] em28xx_write_regs_req+0x37/0x1c0 [em28xx]
[10856.191028] RSP: 0018:ffff880118401a58  EFLAGS: 00010282
[10856.196533] RAX: 00020000012d0000 RBX: ffff88010804aec8 RCX: ffff880118401b14
[10856.203852] RDX: 0000000000000048 RSI: 0000000000000000 RDI: ffff88010804aec8
[10856.211174] RBP: ffff880118401ac8 R08: 0000000000000001 R09: 0000000000000000
[10856.218496] R10: 0000000000000000 R11: 0000000000000006 R12: 0000000000000048
[10856.226026] R13: ffff880118401b14 R14: ffff88011752b258 R15: ffff88011752b258
[10856.233352] FS:  00007f26636d2740(0000) GS:ffff88011fc20000(0000) knlGS:0000000000000000
[10856.241626] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10856.247565] CR2: 00007f2663716e20 CR3: 00000000c7eb1000 CR4: 00000000000007e0
[10856.254889] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[10856.262215] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[10856.269542] Process dvbv5-zap (pid: 13606, threadinfo ffff880118400000, task ffff8800cd625d40)
[10856.278340] Stack:
[10856.280564]  ffff88011ffe8de8 0000000000000002 0000000000000000 ffff88011ffe9b00
[10856.288191]  ffff880118401b14 00ff88011ffe9b08 ffff880100000048 ffffffff8112a52a
[10856.295893]  0000000000000001 ffff88010804aec8 0000000000000048 ffff880118401b14
[10856.303521] Call Trace:
[10856.306182]  [<ffffffff8112a52a>] ? __alloc_pages_nodemask+0x15a/0x960
[10856.312912]  [<ffffffffa045a002>] em28xx_write_regs+0x32/0xa0 [em28xx]
[10856.319638]  [<ffffffffa045a221>] em28xx_write_reg+0x21/0x30 [em28xx]
[10856.326279]  [<ffffffffa045a2cc>] em28xx_gpio_set+0x9c/0x100 [em28xx]
[10856.332919]  [<ffffffffa045a3ac>] em28xx_set_mode+0x7c/0x80 [em28xx]
[10856.339472]  [<ffffffffa03ef032>] em28xx_dvb_bus_ctrl+0x32/0x40 [em28xx_dvb]

This is caused by commit c7a45e5b,
that added support for two I2C buses. A partial fix was applied
at 3de09fbb, but it doesn't cover
all cases, as the DVB core fills fe->dvb->priv with adapter->priv.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

dvb->adapter.priv should also be set to the i2c bus since that's what
em28xx_tuner_callback expects.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is an hybrid board. However, for analog, it requires
a new driver for saa7136. So, for now, let's just add
support for Digital TV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Newer em28xx devices have 2 buses. Change the logic to allow
using both buses.
This patch was generated by this small script:
for i in drivers/media/usb/em28xx/*.c; do
	sed 's,->i2c_adap,->i2c_adap[dev->def_i2c_bus],g;s,->i2c_client,->i2c_client[dev->def_i2c_bus],'
done
Of course, em28xx.h needed manual edit.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

DEV_INITIALIZED of enum em28xx_dev_state state is used nowhere and there is no
need for DEV_MISCONFIGURED, so remove this enum and use a boolean field
'disconnected' in the device struct instead.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch converts the em28xx driver over to videobuf2.  It is
likely that em28xx_fh can go away entirely, but that will come in
a separate patch.

[mchehab@redhat.com: fix a non-trivial merge conflict with some VBI
 patches; CodingStyle fixes]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current enpoint logic ignores all bulk endpoints and uses
a fixed mapping between endpint addresses and the supported
data stream types (analog/audio/DVB):
  Ep 0x82, isoc	=> analog
  Ep 0x83, isoc	=> audio
  Ep 0x84, isoc	=> DVB
Now that the code can also do bulk transfers, the endpoint
logic has to be extended to also consider bulk endpoints.
The new logic preserves backwards compatibility and reflects
the endpoint configurations we have seen so far:
  Ep 0x82, isoc		=> analog
  Ep 0x82, bulk		=> analog
  Ep 0x83, isoc*	=> audio
  Ep 0x84, isoc		=> digital
  Ep 0x84, bulk		=> analog or digital**
 (*: audio should always be isoc)
 (**: analog, if ep 0x82 is isoc, otherwise digital)

[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
 into separate lines]
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also improve the comments.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The URB data processing for DVB bulk transfers is very similar to
what is done with isoc transfers, so create a common function that
works with both transfer types based on the existing isoc function.
Tested with device Hauppauge HVR-930c.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This check is already done in the URB handler
em28xx_irq_callback before calling these functions.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>