Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.

To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.

This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.

Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.

The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified:  INIT-to-RTR, and SQD-to-SQD.

Similarly for the alternate path information.

Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.

For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
   MAC information to the operational information, and reset
   the candidate MAC info.
2. If there was a previous MAC, unregister it.  Then move
   the MAC information from candidate to operational, and
   reset the candidate info (as in 1. above).

The MAC address failure logic is the same for all cases:
 - Unregister the candidate MAC, and reset the candidate MAC info.

For Vlan registration, the logic is similar.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs:  Remaining GIDS are divided evenly between VFs activated by the driver.
      If the division is not even, lower-numbered VFs get an extra GID.

For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.

This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump all Mellanox driver versions.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should use rdma_vlan_dev_real_dev() instead of using vlan_dev_real_dev()
when building the GID table for a vlan interface.
Signed-off-by: NDevesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Use correct value for obtaining traffic class from device
response for Query QP request.
Signed-off-by: NDevesh Sharma <devesh.sharma@emulex.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Error reported at http://marc.info/?l=linux-rdma&m=138995755801039&w=2

Fix short to int cast for big endian systems.
Signed-off-by: NUpinder Malhi <umalhi@cisco.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Research has shown that commit a77fcf89 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.

This patch add that sequence.

Cc: <stable@vger.kernel.org>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly.  For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The IBoE code used to reset the GID table did it for all Ethernet
ports of the device.  Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table.  Change the reset flow to be
per-port.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Updating the GID table under IBoE requires read/write from/to shared
data structures.  These data structures are protected with the device
iboe lock.  The flows that modify the GID table start from

    1. Initializing the GID table
    2. NETDEV events
    3. INET or INET6 events

This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held.  On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.

This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.

Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned.  This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When the device has only Ethernet ports, don't try to allocate range
of steerable UD QPs since they aren't needed.  This fixes an issue
where mlx4 VFs tried to allocate a range of UD steerable QPs, but
failed to do so.

Fixes: c1c98501 ("IB/mlx4: Add support for steerable IB UD QPs")
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Set the return variable to an error code as done elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Set the return variable to an error code as done elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Currently Connect-IB does not support blocking multicast loopback, so
don't set IB_DEVICE_BLOCK_MULTICAST_LOOPBACK in the device caps.

Reported by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Commit c1be5232 ("Fix micro UAR allocator") broke binary compatibility
between libmlx5 and mlx5_ib since it defines a different value to the number
of micro UARs per page, leading to wrong calculation in libmlx5. This patch
defines struct mlx5_ib_alloc_ucontext_req_v2 as an extension to struct
mlx5_ib_alloc_ucontext_req.  The extended size is determined in mlx5_ib_alloc_ucontext()
and in case of old library we use uuarn 0 which works fine -- this is
acheived due to create_user_qp() falling back from high to medium then to
low class where low class will return 0.  For new libraries we use the
more sophisticated allocation algorithm.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NYann Droneaud <ydroneaud@opteya.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: NYann Droneaud <ydroneaud@opteya.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The current code attmepts to call ib_umem_get() even if the length is
zero, which causes a failure. Since the spec allows zero length work
queues, change the code so we don't call ib_umem_get() in those cases.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Modify CQ is used by ULPs like IPoIB to change moderation parameters.  This
patch adds support in mlx5.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Put a wmb() to make sure the doorbell record is visible to the HCA before we
hit doorbell.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Use the possibly more efficient ether_addr_equal() instead of memcmp().
Signed-off-by: NWang Weidong <wangweidong1@huawei.com>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The GSI QP type is compatible with and should be allowed to send data
to/from any UD QP.  This was found when testing ibacm on the same node
as an SA.

Cc: <stable@vger.kernel.org>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Building mem.o for 32 bits x86 triggers a GCC warning:

    drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
    drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64.  That's what _c4iw_write_mem_inline() already does.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Remove including <linux/version.h> that don't need it.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

There is a path in handle_vq() where kmem_cache_free() can be called
with pointer to a local variable.  It can happen if vq_repbuf_alloc()
failed to allocate memory from cache and req is NULL.

The patch adds check if cache memory was allocated before freeing it.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NSvetlana Mavrina <another.karnil@gmail.com>
Reviewed-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This is called from qp_grp_and_vf_bind() and we are holding the
vf->lock so the allocation can't sleep.

Fixes: e3cf00d0 ('IB/usnic: Add Cisco VIC low-level hardware driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

...instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Now that ocrdma supports IP-based addressing, we need to depend on
INET, since ocrdma registers itself for net device events.
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This fixes the build if IPV6 isn't enabled.
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Since mlx4_ib supports IP based addressing, a dependency on INET needs
to be added, since mlx4_ib registers itself for net device events.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch is similar in spirit to the "IB/mlx4: Use IBoE (RoCE) IP
based GIDs in the port GID table" patch.

Changes to inet4 and inet6 addresses for the host are monitored and if
the address is associated with an ocrdma device then a gid is added or
deleted from the device's gid table. The gid format will be a IPv4 to
IPv6 mapped or the IPv6 address.

Cc: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch is similar in spirit to the "IB/mlx4: Handle Ethernet L2
parameters for IP based GID addressing".  It handles the fact that IP
based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.

When building an address handle, instead of parsing the dgid to
get the MAC and VLAN, take them from the address handle attributes.

Cc: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>