This patch (as1046) makes USB-PERSIST work more in accordance with
the documentation.  Currently it takes effect only in cases where the
root hub has lost power or been reset, but it is supposed to operate
whenever a power session was dropped during a system sleep.

A new hub_restart() routine carries out the duties required during a
reset or a reset-resume.  It checks to see whether occupied ports are
still enabled, and if they aren't then it clears the enable-change and
connect-change features (to prevent interference by khubd) and sets
the child device's reset_resume flag.  It also checks ports that are
supposed to be unoccupied to verify that the firmware hasn't left the
port in an enabled state.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1045) reorganizes some code in the hub driver.
hub_port_status() is moved earlier in the file, and a new hub_stop()
routine is created to do the work currently in hub_preset() (i.e.,
disconnect all child devices and quiesce the hub).

There are no functional changes.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset.  This is necessary because:

	When some machines go into suspend, they remove power from
	on-board USB devices while retaining suspend current for USB
	controllers.

	The user might well unplug a USB device while the system is
	suspended and then plug it back in before resuming.

A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep.  If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.

Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the HP hs2300 Broadband Wireless Module (relabeled MC8775) USB IDs
Signed-off-by: NStefan Seyfried <seife@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the leak of the snap structure allocated in mon_stat_open().
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

The num_interrupt_in, num_bulk_in, and other checks in the usb-serial
code are just wrong, there are too many different devices out there with
different numbers of endpoints.  We need to just be sticking with the
device ids instead of trying to catch this kind of thing.  It broke too
many different devices.

This fixes a large number of usb-serial devices to get them working
properly again.


Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add new vendor ID and device ID  for AMOI HSDPA modem. 

From: tang kai <tangk73@hotmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 - declare the unusal device for Huawei data card devices in
   unusual_devs.h
 - disable the product ID matching for Huawei data card devices in
   usb_match_device function of driver.c
 - declare the product IDs in option.c.
Signed-off-by: Nfangxiaozhi <huananhu@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add devices by AMOI and NovatelWireless.
Signed-Off-By: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The modem was detected, the ttyUSB{0,1,2} appeared, a call could be
made, and the expected data rate was achieved.  Tested for an hour or
two, total of 100Mb.  I shall do more testing.
Signed-off-by: NJames Cameron <quozl@laptop.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable usb
peripheral drivers, to re-eable module auto loading.

[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is part of the series adding support for the USB High
Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9
uses the same UDPHS IP as the AVR32 and the AT91SAM9RL.

The only differences between the AVR32 and the AT91 version of the
device are in the enable/disable and suspend/wakeup sequences: the
AT91 version needs to toggle the USB bias and pulldown explicitly.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

Signed-off-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

The atmel_usba_udc driver is being used by several platforms and arches
(avr32 and at91 ATM), and each platform may have different endpoint
settings.

The patch below moves the endpoint declarations into the platform
data and make the necessary adjustments for AVR32 (improved by
Haavard Skinnemoen <hskinnemoen@atmel.com>).
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>

GPIO_PIN_NONE should no longer be used. Replace it with a simple
test against negative values.

This is a transitional patch, waiting for gpio_is_valid() to be
merged at which point the tests should be revisited.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>

The endpoints of the atmel_usba_udc driver do not have directional
(in/out) or usage (ctrl/bulk/iso) restrictions, as their names
incorrectly implied.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>

These functions do exactly the same as memcpy_toio() and
memcpy_fromio() respectively.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>

Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ).  The timer would then fire at time (0 <= T <
HZ).

Fix them to use round_jiffies(jiffies + HZ);
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes the keyspan driver after the addition of additional
checking of driver requirements introduced in usb-serial.c
commit 063a2da8.  The initialization
of the keyspan usb_serial_driver structs were not initializing the
num_interrupt_out field and the additional checking was rejecting
the end point so the driver wouldn't finish initializing.

This commit initializes the fields to NUM_DONT_CARE.
It works for the keyspan USA-49WG and doesn't break the USA-19HS
which are the two keyspan devices I have to test with.
Signed-off-by: NClark Rawlins <clark.rawlins@escient.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1062) fixes a bug in the scatter-gather initialization
code in the usbtest driver.  When the sg-helper conversion was
performed, it wasn't done correctly.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes a bug/inconsistency revealed by the additional sanity checking in
   commit 063a2da8
introduced in the original 2.6.24 branch.

The Handspring Visor / PalmOS 4 device structure defines .num_bulk_out=2
but the usb-serial probe returns num_bulk_out=3, triggering the check in
the above commit and forcing a bail out when the device (a Garmin iQue in
my case) attempts to connect.  The patch bumps the expected number of
endpoints to 3.

FWIW, this patch will probably solve the following kernel bug report for
Treo users (identical symptoms, different model PalmOS units):
  <http://bugzilla.kernel.org/show_bug.cgi?id=10118>
Signed-off-by: NBrad Sawatzky <brad+kernel@swatter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the Telegesys ETRX2USB which
works fine with the cp2101 driver.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Tested-by: NXavier Carcelle <xavier.carcelle@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The changes introduced in commit
063a2da8 changed the semantics of the
num_interrupt_in, num_interrupt_out, num_bulk_in and num_bulk_out
entries of the usb_serial_driver struct to be the number of endpoints
the device has when probed.

This patch changes the ti_1port_device usb_serial_driver struct to
reflect this change.  The single port devices only have 1
bulk_out endpoint in their initial configuration, and so this patch
changes the number of other types to NUM_DONT_CARE.

The same change probably needs doing to the ti_2port_device struct,
but I don't have a two port device at hand.
Signed-off-by: NRobert Spanton <rspanton@zepler.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch, suggested by Alan Stern, fixes the hung USB issues
on my notebook from suspend/resume cycles.

It does so by eliminating some confusion about the internal state
machine associated with unlinking from the EHCI async schedule ring,
which caused a recent regression:

  http://bugzilla.kernel.org/show_bug.cgi?id=10345Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Make it possible to pass mbus_dram_target_info to the ehci-orion
driver via the platform data, make the ehci-orion driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the EHCI mbus window registers by hand.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The VIA VT6212 defaults to only waiting 1us between passes over EHCI's
async ring, which hammers PCI badly ... and by preventing other devices
from accessing the bus, causes problems like drops in IDE throughput,
a problem that's been bugging users of those chips for several years.

A (partial) datasheet for this chip eventually turned up, letting us
see how to make it use a VIA-specific register to switch over to the
the normal 10us value instead, as suggested by the EHCI specification
Solution noted by Lev A. Melnikovsky.

It's not clear whether this register exists on other VIA chips; we
know that it's ineffective on the vt8235.  So this patch only applies
to chips that seem to be incarnations of the (discrete) vt6212.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Tested-by: NLev A. Melnikovsky <melnikovsky@mail.ru>
Tested-by: NAlessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for the MC8775 device to the sierra driver.
Signed-off-by: NKevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

while I was adding autosuspend to that driver I noticed a few issues.
You were having DMAed buffers as a part of a structure.
This will fail on platforms that are not DMA-coherent (arm, sparc, ppc, ...)
Please test this patch to fix it.
Signed-off-by: NKevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.
Signed-off-by: NConstantin Baranov <const@tltsu.ru>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the inquiry fails then the info structure on us->extra was not freed.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Device like this http://aldiga.com/english/A-100-USB-EDGE10.htm
contains Prolific 2303 chip.
Actually their site a bit outdated - I have AlDiga AL-11U
GSM/GPRS/EDGE modem and it works with pl2303 module after adding
corresponding product ID.

By default modem uses baud rate 460800.  GSM chipset - SIMCom SIM600,
quad band 850/900/1800/1900 MHz

Device info:

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=067b ProdID=0611 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=pl2303
E:  Ad=81(I) Atr=03(Int.) MxPS=  10 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

From: Max Arnold <lwarxx@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request.  A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

gadgetfs (drivers/usb/gadget/inode.c) was not delegating all
non-device requests to userspace.  This patch makes the handling of
all request cases consistent.
Signed-off-by: NRoy Hashimoto <hashimot@alumni.caltech.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since the separation of sense_buffer from scsi_cmnd, Drivers that hack their
own struct scsi_cmnd like here isd200, must also take care of their own
sense_buffer.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The recent EHCI driver update to split the IAA watchdog timer out from
the other timers made several things work better, but not everything;
and it created a couple new issues in bugzilla.  Ergo this patch:

  - Handle a should-be-rare SMP race between the watchdog firing
    and (very late) IAA interrupts;

  - Remove a shouldn't-have-been-added WARN_ON() test;

  - Guard against one observed OOPS;

  - If this watchdog fires during clean HC shutdown, it should act
    as a NOP instead of interfering with the shutdown sequence;

  - Guard against silicon errata hypothesized by some vendors:
      * IAA status latch broken, but IAAD cleared OK;
      * IAAD wasn't cleared when IAA status got reported;

The WARN_ON is in bugzilla as 10168; the OOPS as 10078; these are
both regressions.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Tested-by: NGordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: NMirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>