We have no idea how many VIFs there are requiring a special spare, we
know just about the number of keys set. Rename the counter appropriately
and toggle it whenever a special key is added/removed.
Previously this was only changed once, since it was toggled whenever
the actual spare was changed.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

FW API changed and now PERIODIC_SCAN_REPORT_EVENT is sent
in case results were found at the end of each sched scan
cycle. Previous FW was missing that and broke sched scan.

This API change is available from 18xx FW 8.5.0.0.27

[Arik - move changes to 18xx specific files, align FW structures to
latest for scan command]
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Don't use MIMO rates when HT mode is forced to SISO, even if we have
multiple antennas.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Treat a single connected STA in PSM as a slow link and regulate Tx speed
according to slow link priority/stop thresholds.
This allows us to avoid flooding the FW, while delivering decent
throughput to a peer in forced-PSM.

[Small simplification of the if statements -- Luca]
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update the 18xx FW status private part to include Tx related link
priorities. Introduce new HW ops to determine link priority per chip
family.

For 18xx the changes are:
- Suspended links are at most low priority and Tx for them is stopped
  beyond the suspend threshold.
- Active links now get their thresholds directly from FW
- There's a new "stop" threshold for active links, at which point a link
  stops receiving new packets.

Update the min 18xx FW version required to make sure suspended links
bitmap is advertised by the FW.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl->num_rx_desc was mistakenly initialized with WL18XX_NUM_TX_DESCRIPTORS
but it should use WL18XX_NUM_RX_DESCRIPTORS instead.

This bug was passed unnoticed because currently both RX and TX descriptors
are initialized to the same value (32).
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

There's a limit on scan dwell times of max 30ms in order
to avoid degrading voip traffic which could be going on
while scanning. However these dwell times increase the
chance of missing out on nearby APs leading to partial
scan results. Allow configuration of longer dwell times
in case there no active interface (i.e. no STA associated
or AP up).

[Arik - count started vifs using an in-driver function]

[Fixed some new checkpatch warnings regarding comments in the
networking subsystem. -- Luca]
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

ACX_PEER_CAP command is just ACX_PEER_HT_CAP, but allows
configuring the peer's support rates as well.

this is needed because we start the station role when
the remote rates are not known yet.

the two commands should be unified in future fw versions,
but for now add a new set_peer_cap per-hw op, that will
use ACX_PEER_CAP for 18xx, and ACX_PEER_HT_CAP for 12xx.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prioritize EDCA by choosing the AC before anything else. Use the
fast/slow link bitmap in FW to improve the scheduling algorithm for
the multi-link scenario.

Set packet thresholds to determine if a given link is high or low
priority according to its speed. A slow link will be given high priority
if the amount of packets queued for it in the FW is lower than the
slow-threshold. Similarly, a fast link will be given high priority if
the number of its packets queued in FW is smaller than the high-threshold.

The improved algorithm:
1. Choose optimal AC according to FW utilization
2. Traversing the VIFs in a round-robin fashion, try to choose a high
   priority link. Links are traversed in a round-robin fashion inside a
   VIF.
3. If no high priority links are found, choose the first non-empty
   (low priority) link found in the round robin.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The 18xx fw supports greenfield so add the
IEEE80211_HT_CAP_GRN_FLD flag to the supported
ht capabilities flags.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

all the current firmwares support elp, so
we can safely remove WLCORE_QUIRK_NO_ELP.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

First set (low, medium and high TX power values) is used
for STA-HP background role. The 2nd set is used for other roles.

Update other mac/phy parameters according to new FW.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Conflicts:
	drivers/net/wireless/ti/wl18xx/main.c

Update mac/phy paramters according to the default HP SISO boards.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Previously we were only checking the single-role firmware version.
Now add code to check for the firmware versions separately for each
firmware type.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add support for recovery settings including bug_on_recovery and
no_recovery options.

These options can now be set using wl18xx-conf.bin file and wlconf
tool.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

18xx chips are capable of staying on 2 channels at the same time.
Introduce a chip-family specific parameter to set the number of channels
in the interface-combinations published by the driver.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We support changing the channel BW when we started the STA role on
a 40Mhz bandwidth. Otherwise a reconnection is required.
Save the started channel width and use it when channel width updates
arrive.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Allow configuring different dwell times to the different
scan types (regular and scheduled).

Add new configuration entry (dwell_time_dfs) to
conf_scan_settings, in order to allow setting
different values for normal scan and scheduled scan.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

we have done updating the driver to the new fw
api, so make the driver operational again.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.

The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.

The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".

No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.

[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The event mailbox in wl18xx has a different
(non-compatible) structure.

Create common functions in wlcore to handle the
events, and call them from the chip-specific
event mailbox parsers.

This way, each driver (wl12xx/wl18xx) extracts
the event mailbox by itself according to its
own structure, and then calls the common
wlcore functions to handle it.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Some fields were added to the channel_switch and
stop_channel_switch commands. Unfortunately,
the new 18xx channel_switch struct is not backward
compatible with the 12xx channel switch struct.

Add a new channel_switch op to wlcore, and update
the driver accordingly.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Some regdomains have more than 23 valid 5ghz channels,
so 18xx's MAX_CHANNELS_5GHZ was increased to 32.

Since now we have different max 5ghz channels values
for wl12xx and wl18xx, add a new wl->max_channels_5ghz
field, and use it for scan channels configuration.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.

(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)

New wlcore ops are introduced in order to call the
chip-specific scan functions.

The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The new fw (8.5.0.0.28) is not backward compatible
with older drivers.

Use a new fw name (along with bumping the min
fw version), and add some code to fail
any boot attempt during the fw api alignment
patches (as the driver is not functional in
these transitional patches).

This code will be removed after the api alignment
will be done.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wlcore_op_set_key() calls wl18xx_set_key(),
which in turn executes some of his function
calls without acquiring wl->mutex and making
sure the fw is awake.

Adding mutex_lock()/ps_elp_wakeup() calls is
not enough, as wl18xx_set_key() calls
wl1271_tx_flush() which can't be called while
the mutex is taken.

Add the required calls to wlcore_op_set_key,
but limit the queues_stop and flushing
to the only encryption types in which
a spare block might be needed (GEM and TKIP).

[Arik - move state != ON check]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Move most of the device-specific probe functionality into setup(), a new
op. By doing this, wlcore_probe will be the first to request a firmware
from userspace, making it easier to load the NVS file asynchronously.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The driver used siso20 in this case for legacy reasons.
Reported-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The interrupt line is enabled by wl12xx_enable_interrupts and
wl18xx_enable_interrupts, but it will not be disabled in all failure
paths. Fix this.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

add phy_fw_version_str to debugfs driver_state file.
information is taken during boot and stored in wl->chip.phy_fw_ver_str.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Use number_of_assembled_ant5 phy param to indicate if A band is enabled:
if number_of_assembled_ant5 != 0 then it is enabled otherwise it is
disabled.

This aligns with phy implementation that uses this param both to indicate
if band is active and the number of antennas.

This parameter replaces enable_11a module param that was removed.

User-Space applications can use wlconf and/or INI files to disable A band
using this parameter.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Aggregation buffer size is set separately per 18xx/12xx chip family.
For 18xx aggragation buffer is set to 13 pages to utilize all
the available tx/rx descriptors for aggregation.

[Arik - remove redundant parts from the patch]
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

Use defines for number of Tx/Rx descriptors.
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The new FWs support a bigger BA window.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

default switch configuration set to pg2 chips (rdl 1/2/3/4).
removed hacks for specific board types.
pg1.x boards are now supported only using module params
or specific conf files.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

the driver's init and exit routines can be implemented with the
module_platform_driver, as the init and exit code is same as
that of the module_platform_driver
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use this opportunity to consolidate the check for MIMO support into a
separate function.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>