Fix this sparse warning:
  sound/pci/hda/hda_codec.c:1544:19: warning: incorrect type in assignment (different signedness)
  sound/pci/hda/hda_codec.c:1544:19:    expected unsigned long *vals
  sound/pci/hda/hda_codec.c:1544:19:    got long *<noident>
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the pseudo device-locking using card->shutdown flag to avoid
the crash via clear/reconfig during operations.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the helper function snd_hda_multi_out_dig_cleanup() to clean up
the digital outputs with multi setup.  This call is needed in cases
the codec supports multiple digital outputs as slaves.  Otherwise the
slave widgets aren't properly cleaned up.

For a single digital output (e.g. in patch_conexant.c), this call isn't
needed.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Detect multiple digital-out pins in snd_hda_parse_pin_defconfig().
The dig_out_pin and dig_out_type fields become arrays.

The codec parser still doesn't use this multiple pins detection, though.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add the SPDIF pin as slave digital out to enable concurrent
HDMI/SPDIF outputs for ASUS M3A-H/HDMI with ALC1200 codec.
Tested-by: NThomas Schneider <nailstudio@gmx.net>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add dig_out_type and dig_in_type fields to autocfg struct.
A proper HDA_PCM_TYPE_* value is assigned to these fields according
to the pin-jack location type value.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the volume offset to base for the standard volume controls
to handle elements with too big volume scales like -96dB..0dB.
For such elements, you can set the base volume to reduce the range.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Gateway notebooks have their ID inside codec vendor ID, not at PCI ID. Due to
that, model auto-detection were not possible with the standard seek method.

This is what is found at lspci -vnn:

00:14.2 Audio device [0403]: ATI Technologies Inc SB450 HDA Audio [1002:437b] (rev 01)
        Subsystem: ATI Technologies Inc SB450 HDA Audio [1002:437b]

Yet, autodetection is possible, since the codec properly reflects the vendor at
the Subsystem ID:

$ cat /proc/asound/card0/codec#0 |head -4

Codec: SigmaTel STAC9250
Address: 0
Vendor Id: 0x83847634
Subsystem Id: 0x107b0367

This patch adds a new autodetection function that seeks for codec subsystem ID.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Make the codec re-configuration feature selectable via Kconfig,
CONFIG_SND_HDA_RECONFIG.
Also mark it as experimental (as it really is).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Release ELD proc file when reconfigured so that no leak occurs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Introduce a global function snd_print_pcm_bits() and use it in the ELD code.
Signed-off-by: NWu Fengguang <wfg@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rename struct sink_eld to hdmi_eld.
Signed-off-by: NWu Fengguang <wfg@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

code refactor: make a global function snd_print_channel_allocation().
Signed-off-by: NWu Fengguang <wfg@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Create /proc/asound/card<card_no>/eld#<codec_no> to reflect the audio
configurations and capabilities of the attached HDMI sink.

Some notes:

- Shall we show an empty file if the ELD content is not valid?
  Well it's not that simple. There could be partially populated ELD,
  and there may be malformed ELD provided by buggy drivers/monitors.
  So expose ELD as it is.

- The ELD retrieval routines rely on the Intel HDA interface,
  others are/could be universal and independent ones.

- How do we name the proc file?
  If there are going to be two HDMI pins per codec, then the current naming
  scheme (eld#<codec no>) will fail. Luckily the user space dependencies should
  be minimal, so it would be trivial to do the rename if that happens.

- The ELD proc file content is designed to be easy for scripts and human reading.
  Its lines all have the pattern:
	  <item_name>\t[\t]*<item_value>
  where <item_name> is a keyword in c language, while <item_value> could be any
  contents, including white spaces. <item_value> could also be a null value.
Signed-off-by: NWu Fengguang <wfg@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ELD handling routines can be shared by all HDMI codecs,
and they are large enough to make a standalone source file.
Signed-off-by: NWu Fengguang <wfg@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We want to share some code with print_pcm_rates(),
so extract a common routine snd_print_pcm_rates() from it.
Signed-off-by: NWu Fengguang <wfg@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just cosmetic fixes of spacing that annoyed me.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the sysfs entries to hwdep devices so that the new features
like reconfiguration can be done via sysfs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the reconfiguration feature of any individual codec.
Via the reconfiguration, the old resources are released and
the patch is called again to recreate the PCM and mixers in
addition to the re-initialization.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Manage all kcontrol elements created in the hda-intel driver.
This makes it possible to remove and reconfigure the controls
of each codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Explain some of the magic numbers I saw while trying to fix the AD1989 SPDIF
issue. Maybe should just use the expanded form directly in the verbs?
Signed-off-by: NRobin H. Johnson <robbat2@gentoo.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added support for controlling hardware gain amps on input ports
using a volume control mixer with a mux selecting the port being controlled.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Move the codes for virtual master controls to sound core part so that
not only hda-intel drivers can use it.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs.  When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.

Turning this switch off has a merit for some codecs, though.  Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Allows for dynamically creating mono out mixer controls and well
as mono mux controls.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added a mono_out_pin field to autocfg struct, and code to parse
for the mono_out_line.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Don't query a widget parameter for an invalid NID in get_wcaps() but
rather returns zero (i.e. no attribute).
The read to an non-existing widget may result in a fatal codec
communication error.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added helper functions to implement virtual master volume controls.
The virtual master control is a control element that has multiple
slave controls.  The value of master element is equally added to
slave elements.
The functions are written for general purpose, but it's put in the
HD-audio directory as now, since HD-audio driver is the only user.
It should be moved to the common place once after other drivers use
vmaster.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

AD1986A has a hardware problem that it cannot share a stream with
multiple pins properly.  The problem occurs e.g. when a volume is changed
during playback.
So far, hda-intel driver unconditionally assigns the stream to multiple
output pins in copy-front mode, and this should be avoided for AD1986A
codec.
The original fix patch was by zhejiang <zhe.jiang@intel.com>.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

dac_nids arrays in each codec support code may have up to 5 items
when assigned from the auto-configurator.  Some codec codes have
less numbers than the possible max.  This patch defines the constant
and fixes the array definitions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fixed the build error from patch_sigmatel.c when built without
CONFIG_SND_HDA_GENERIC by defining a dummy function to return error.
Also, clean up hda_codec.c by removing unneeded ifdefs (the compiler
will optimize out).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added CONFIG_SND_HDA_POWER_SAVE kconfig.  It's an experimental option
to achieve an aggressive power-saving.  With this option, the driver
will turn on/off the power of each codec and controller chip dynamically
on demand.
The patch introduces a new module option 'power_save'.  It specifies
the second of time-out for automatic power-down.  As default, it's
10 seconds.  Setting 0 means to suppress the power-saving feature.
The codec may have analog-input loopbacks, which are usually represented
by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'.
When these are on, we cannot turn off the mixer and the codec chip has
to be kept on.  For bookkeeping these states, a new codec-callback is
introduced.
For the bus-controller side, a new callback pm_notify is introduced,
which can be used to turn on/off the contoller appropriately.
Note that this power-saving might cause slight click-noise at
power-on/off.  Also, it might take some time to wake up the codec, and
might even drop some tones at the very beginning.  This seems to be the
side-effect of turning off the controller chip.
This turn-off of the controller can be disabled by undefining
HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added snd_hda_codec_amp_stereo() function that changes both of stereo
channels with the same mask and value bits.  It simplifies most of
amp-handling codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

So far, the driver looked the table of snd_kcontrol_new used for creating
mixer elements and forces to call each of its put callbacks in PM resume
code.  This is too ugly and hackish.
Now, the resume is simplified using the codec amp and command register
caches.  The driver simply restores the values that have been written
in the cache table.  With this simplification, most codec support codes
don't require any special resume callback.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds the cache for codec command registers.
snd_hda_codec_write_cache() and snd_hda_sequence_write_cache() do
the write operations with caching, which values can be resumed via
snd_hda_codec_resume_cache().
The patch introduces only the framework, and no codec code is using
this cache yet.  It'll be implemented in the following patch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added callbacks for a generic bind-control of mixer elements.
This can be used for creating a mixer element controlling multiple
widgets at the same time.  Two macros, HDA_BIND_VOL() and HDA_BIND_SW(),
are introduced for creating bind-volume and bind-switch, respectively.
It taks the mixer element name and struct hda_bind_ctls pointer, which
contains the real control callbacks in ops field and long array for
private_value of each bound widget.
All widgets have to be the same type (i.e. the same amp capability).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added a hwdep interface for each codec (enabled per kconfig).
This interface can be used for reading/writing HD-audio verbs
and other purposes as future extensions.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fix codes to follow more to the standard kernel coding style.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>