Make the function acquire the necessary mutex itself
to simplify the callers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:

...
Country: US  Environment: Indoor/Outdoor
    ...
    Channels [157 - 157] @ 30 dBm
    ...
Power constraint: 13 dB
...

What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.

Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).

Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: NCarl A. Cook <CACook@quantum-equities.com>
Tested-by: NCarl A. Cook <CACook@quantum-equities.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The functions are only called if CONFIG_PM is set
as the callers are under an ifdef, so there's no
need to also define no-op functions.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

skb->dev might contain a stale reference to a device that was already
deleted, and using it unchecked can lead to invalid pointer accesses.
Since this is only used for nl80211 tx, iterate over active interfaces
to find a match for skb->dev, and discard the tx status if the device
is gone.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 calls synchronize_rcu() on sta deletion,
which increase the roaming time significantly.

Convert it into a call_rcu() mechanism, in order
to avoid blocking. Since some of the cleanup
functions might sleep, schedule from the call_rcu
callback a new work that will do the actual cleanup.

In order to make sure the cleanup occurs before
the interface went down, flush local->workqueue
on ieee80211_do_stop().
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Whenever a host gets an AUTH frame it first allocates a new
station and then replies with another AUTH frame. However,
if sta allocations fails the host should send a DEAUTH frame
instead to tell the other end that something went wrong.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
[reword commit message a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move ieee80211_send_deauth_disassoc() to util.c to make it
available for the rest of the mac80211 code.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
[reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Split functionality for further reuse.

Will prevent code duplication when channel context
channel_type merging is introduced.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

__ieee80211_key_destroy() calls synchronize_rcu() in
order to sync the tx path before destroying the key.

However, synching the tx path can be done with
synchronize_net() as well, which is usually faster
(the timing might be important for roaming scenarios).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The power constraint IE is always a single byte
so check the size when parsing instead of later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Disconnect from the AP if channel switching in the
driver failed or if the new channel is unavailable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to keep a copy of the scheduled
scan IEs after the driver has been told, if it
requires a copy it must make one. Therefore, we
can move sched_scan_ies into the function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using list_move() instead of list_del() + list_add().

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: NYoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Doing so creates warnings, but the function is internal and
not part of the 802.11 docbooks, so it from kerneldoc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ifmgd->bssid wasn't cleared properly in some
auth/assoc failure cases, causing mac80211 and
the low-level driver to go out of sync.

Clear ifmgd->bssid on failure, and notify the driver.

Cc: stable@kernel.org # 3.4+
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A P2P Device interface does not have a netdev, and is not
expected to be used for transmitting data, so there is no
need to assign hw queues for it.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit mac80211: avoid using synchronize_rcu in ieee80211_set_probe_resp
changed the return value when the probe response template is not present.
Revert to the earlier value of 1 - this fixes AP mode for drivers like
ath9k.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.
Reported-by: NCedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to carry around a return value
that is always NETDEV_TX_OK anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In multi-channel scenarios, the channel that we will
transmit a probe request on isn't always the current
channel (which will be NULL anyway) but will instead
be the channel that the AP is on. Pass the channel
to the ieee80211_send_probe_req() function so it can
be used in the different scenarios. The scan code
continues to pass the current channel, of course.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to BUG_ON when a driver registers
invalid operations, warn and return an error.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The optimisation of scanning only on the current
channel should check the operating channel. Also
modify it to compare channel pointer rather than
the frequency.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Even for single-channel devices it is possible that we
switch the channel temporarily (e.g. for scanning) but
while doing so process a received frame that was still
received on the old channel, so checking the current
band is racy. Use the band from status instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With the move to multi-channel and away from
drv_config(), hw.conf.channel will not always
be set, only for devices using the current API
instead of the new channel context APIs. Check
the channel is set before adding its frequency
to the trace data.

Also break some overly long lines in the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using hw.conf.channel is wrong as it could be the
temporary channel if the station is added from the
workqueue while the device is already on another
channel. Use oper_channel instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

You can now get these values through iw, and
they conflict with multi-channel work.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In ieee80211_beacon_get_tim() we can use the
txrc.sband instead of a separate local variable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using local->_oper_channel_type in the mesh code is
completely wrong as this value is the combination
of the various interface channel types and can be
a different value from the mesh interface in case
there are multiple virtual interfaces.

Use sdata->vif.bss_conf.channel_type instead as it
tracks the per-vif channel type.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to use a single scratch buffer and
calculate offsets into it, just use two separate
buffers for the separate variables.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.

This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.

Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.

As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to declare the function in the
header file since it's only used in a single
place, so make it static.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The channel switch IE has a fixed size, so we can
discard it in parsing if it's not the right size
and use the right struct pointer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The time until the channel switch is in TU,
not in milliseconds, so use TU_TO_EXP_TIME()
to correctly program the timer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clean up the CSA handling code by moving some
of it out of the if and using a C99 initializer
for the struct passed to the driver method.

While at it, also add a comment that we should
wait for a beacon after switching the channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to copy the BSSID just to print
it, remove the unnecessary variable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>