akpm: taken from http://bugzilla.kernel.org/show_bug.cgi?id=11587

I bought the wifi dongle trust nw-3100 wich is in fact a zd1211rw.  Its
hardware id was missing in the sources, adding it made it work flawlessly.

Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Connectivtiy is lost after Group rekeying is done. The keytype
maintained by ath9k is reset when group key is updated. Though
sc_keytype can be reset only for broadcast key the proper fix
would be to use mac80211 provided key type from txinfo during
xmit and get rid of sc_keytype from ath9k ath_softc.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Tested-by: NSteven Noonan <steven@uplinklabs.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.

(This is a backport of patch w/ same title already in net-next-2.6.
It is verified to fix http://bugzilla.kernel.org/show_bug.cgi?id=11394
and it should be acceptable for -rc due to the driver being new
in 2.6.27.)
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.

Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.

This patch fixes memory freeing problem in the previous patch.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NIan Schram <ischram@telenet.be>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error.  Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: NCahill Ben <ben.m.cahill@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.

As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.

Pasted the kernel warning message for reference.

kernel: ath0: No ProbeResp from current AP 00:1b:11:60:7a:3d - assume out of range
kernel: ------------[ cut here ]------------
kernel: WARNING: at kernel/softirq.c:136 local_bh_enable+0x3c/0xab()
kernel: Pid: 1029, comm: ath9k Not tainted 2.6.27-rc4-wt-w1fi-wl
kernel:
kernel: Call Trace:
kernel:  [<ffffffff802278d8>] warn_on_slowpath+0x51/0x77
kernel:  [<ffffffff80224c51>] check_preempt_wakeup+0xf3/0x123
kernel:  [<ffffffff80239658>] autoremove_wake_function+0x9/0x2e
kernel:  [<ffffffff8022c281>] local_bh_enable+0x3c/0xab
kernel:  [<ffffffffa01ab75a>] ath_rx_node_cleanup+0x38/0x6e [ath9k]
kernel:  [<ffffffffa01b2280>] ath_node_detach+0x3b/0xb6 [ath9k]
kernel:  [<ffffffffa01ab09f>] ath9k_sta_notify+0x12b/0x165 [ath9k]
kernel:  [<ffffffff802366cf>] queue_work+0x1d/0x49
kernel:  [<ffffffffa018c3fc>] add_todo+0x70/0x99 [mac80211]
kernel:  [<ffffffffa017de76>] __sta_info_unlink+0x16b/0x19e [mac80211]
kernel:  [<ffffffffa017e6ed>] sta_info_unlink+0x18/0x43 [mac80211]
kernel:  [<ffffffffa0182732>] ieee80211_associated+0xaa/0x16d [mac80211]
kernel:  [<ffffffffa0184a1a>] ieee80211_sta_work+0x4fb/0x6b4 [mac80211]
kernel:  [<ffffffff80469c58>] thread_return+0x30/0xa9
kernel:  [<ffffffffa018451f>] ieee80211_sta_work+0x0/0x6b4 [mac80211]
kernel:  [<ffffffff802362c2>] run_workqueue+0xb1/0x17a
kernel:  [<ffffffff80236be9>] worker_thread+0xd0/0xdb
kernel:  [<ffffffff8023964f>] autoremove_wake_function+0x0/0x2e
kernel:  [<ffffffff80236b19>] worker_thread+0x0/0xdb
kernel:  [<ffffffff8023954a>] kthread+0x47/0x75
kernel:  [<ffffffff80223121>] schedule_tail+0x18/0x50
kernel:  [<ffffffff8020bc49>] child_rip+0xa/0x11
kernel:  [<ffffffff80239503>] kthread+0x0/0x75
kernel:  [<ffffffff8020bc3f>] child_rip+0x0/0x11
kernel:
kernel: ---[ end trace e9bb5da661055827 ]---
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.

Also use mac80211 provided enums for key length calculation.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.

[ The warning was masked by the old definition of BUILD_BUG_ON() ]

Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The leak in if_cs_prog_helper() is obvious.

It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.

If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.

Only write the multicast addresses we have specifically set.
Signed-off-by: NDavid Kilroy <kilroyd@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes loading firmware from memory above 32bit.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NMarcel Holtmann <holtmann@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds workaround for an interrupt related hardware bug on
some platforms.  (Apparently these platforms boot-up w/ INTX_DISABLED
set. -- JWL)
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

GFP_DMA is not necessary for the iwlwifi hardware and it can cause
allocation failures and/or invoke the OOM killer on lots of systems.

For reference:

	https://bugzilla.redhat.com/show_bug.cgi?id=459709Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bintval is set to the initial value at .config_interface which is too
late, since it overwrites previously set value from .config. Move the
initialization to the .add_interface.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Beacons setup and config was racy with beacon send. Ensure that
ISR and reset functions see consistent state of bbuf.

Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it
from atomic now.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the AP rejects a Shared Key authentication request, try Open System
auth too.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return errors from request_firmware() (like other drivers that do
firmware load on device open) and make up plausible codes for other
error conditions. Gives userspace tools like NetworkManager a clue that
firmware may be missing when the result of setting IFF_UP is ENOENT.
Signed-off-by: NDan Williams <dcbw@redhat.com>

v2: fix reversed check of atmel_wakeup_firmware() in probe_atmel_card()
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/wireless/ath5k/base.c
  drivers/net/wireless/b43/main.c
  drivers/net/wireless/ipw2100.c
  drivers/net/wireless/ipw2200.c
  drivers/net/wireless/iwlwifi/iwl-3945.c
  drivers/net/wireless/iwlwifi/iwl-4965.c
  drivers/net/wireless/iwlwifi/iwl-5000.c
  drivers/net/wireless/iwlwifi/iwl-agn.c
  drivers/net/wireless/iwlwifi/iwl-core.c
  drivers/net/wireless/iwlwifi/iwl-eeprom.c
  drivers/net/wireless/iwlwifi/iwl-hcmd.c
  drivers/net/wireless/iwlwifi/iwl-power.c
  drivers/net/wireless/iwlwifi/iwl3945-base.c

This patch removes the said #include <version.h>.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.

This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(Only important for USB V1 Adaptors)

If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...

But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.

Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add newlines at printk outputs to not break dmesg.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the USB ID for a Netgear WG111v3.
Signed-off-by: Nmatthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding
error and needs the fix found for several other cards.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 256b152b (ath5k: don't enable
MSI, we cannot handle it yet) has removed msi support, but overlooked
the suspend/resume code. This patch completes msi removal.

I don't consider this patch copyrightable, and thus put it into the
public domain. The result is of course a base.c file dual-licensed under
3-clause-BSD and GPL.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit b19fa1fa, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig
option" breaks p54pci and p54usb.

Additionally, the old logic always tx'ed cts frames (if enabled)
with a short preamble when [rate > 3]. (i.e. with any 802.11g rate).
Of course this isn't that bad, but it's still wrong!

(This patch also clarifies the meanings of some of the fields in the tx
header for the hardware. -- JWL)
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(I missed the fact that the original post said to apply this patch
twice... -- JWL)

Original commit log message:

This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.

Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>