We have two close to identical report_user_fault functions.
Add a parameter to one and get rid of the other one in order
to reduce code duplication.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Over time some machine flags got unused (e.g. MACHINE_FLAG_MVPG)
or are available on all 64bit systems (MACHINE_FLAG_CSP,
MACHINE_FLAG_IEEE) - let's remove them.
Reorder the other ones to match the order of the MACHINE_HAS_*
macros and renumber all bits to avoid holes.
Also fix the comment about where the flags are detected.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The program parameter can be used to mark hardware samples with
some token.  Previously, it was used to mark guest samples only.

Improve the program parameter doubleword by combining two parts,
the leftmost LPP part and the rightmost PID part.  Set the PID
part for processes by using the task PID.
To distinguish host and guest samples for the kernel (PID part
is zero), the guest must always set the program paramater to a
non-zero value.  Use the leftmost bit in the LPP part of the
program parameter to be able to detect guest kernel samples.

[brueckner@linux.vnet.ibm.com]: Split __LC_CURRENT and introduced
__LC_LPP. Corrected __LC_CURRENT users and adjusted assembler parts.
And updated the commit message accordingly.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Various functions in entry.S perform test-under-mask instructions
to test for particular bits in memory.  Because test-under-mask uses
a mask value of one byte, the mask value and the offset into the
memory must be calculated manually.  This easily introduces errors
and is hard to review and read.

Introduce the TSTMSK assembler macro to specify a mask constant and
let the macro calculate the offset and the byte mask to generate a
test-under-mask instruction.  The benefit is that existing symbolic
constants can now be used for tests.  Also the macro checks for
zero mask values and mask values that consist of multiple bytes.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.

The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.

Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add the compare-and-delay instruction to the spin-lock and rw-lock
retry loops. A CPU executing the compare-and-delay instruction stops
until the lock value has changed. This is done to make the locking
code for contended locks to behave better in regard to the multi-
hreading facility. A thread of a core executing a compare-and-delay
will allow the other threads of a core to get a larger share of the
core resources.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The vector extension introduces 32 128-bit vector registers and a set of
instruction to operate on the vector registers.

The kernel can control the use of vector registers for the problem state
program with a bit in control register 0. Once enabled for a process the
kernel needs to retain the content of the vector registers on context
switch. The signal frame is extended to include the vector registers.
Two new register sets NT_S390_VXRS_LOW and NT_S390_VXRS_HIGH are added
to the regset interface for the debugger and core dumps.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The original bootmem allocator is getting replaced by memblock. To
cover the needs of the s390 kdump implementation the physical memory
list is used.
With this patch the bootmem allocator and its bitmaps are completely
removed from s390.
Signed-off-by: NPhilipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The zEC12 machines introduced the local-clearing control for the IDTE
and IPTE instruction. If the control is set only the TLB of the local
CPU is cleared of entries, either all entries of a single address space
for IDTE, or the entry for a single page-table entry for IPTE.
Without the local-clearing control the TLB flush is broadcasted to all
CPUs in the configuration, which is expensive.

The reset of the bit mask of the CPUs that need flushing after a
non-local IDTE is tricky. As TLB entries for an address space remain
in the TLB even if the address space is detached a new bit field is
required to keep track of attached CPUs vs. CPUs in the need of a
flush. After a non-local flush with IDTE the bit-field of attached CPUs
is copied to the bit-field of CPUs in need of a flush. The ordering
of operations on cpu_attach_mask, attach_count and mm_cpumask(mm) is
such that an underindication in mm_cpumask(mm) is prevented but an
overindication in mm_cpumask(mm) is possible.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

MACHINE_HAS_MVCOS is used exactly once when the machine is brought up.
There is no need to cache the flag in the machine_flags.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently we have hardcoded the HSA size to 32 MiB. With this patch the
HSA size is determined dynamically via SCLP in early.c.
Reviewed-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Simplify the uaccess code by removing the user_mode=home option.
The kernel will now always run in the home space mode.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Simplify the memory detection code a bit by removing the CHUNK_OLDMEM
and CHUNK_CRASHK memory types.
They are not needed. Everything that is needed is a mechanism to
insert holes into the detected memory.
Reviewed-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The current memory detection loop will detect all present memory of
a machine. This is true even if the user specified the "mem=" parameter
on the kernel command line.
This can be a problem since the memory detection may cause a fully
populated host page table for the guest, even for those parts of the
memory that the guest will never use afterwards.

So fix this and only detect memory up to a user supplied "mem=" limit
if specified.
Reported-by: NMichael Johanssen <johanssn@de.ibm.com>
Reviewed-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The variable real_memory_size has odd semantics and has been used in
a broken way by e.g. the old kvm code.
Therefore get rid of it before anybody else makes use of it.
Reviewed-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The set-program-parameter (SPP) instruction has been renamed to
load-program-parameter (LPP) (see SA23-2260).  Reflect this change
and rename all macro/instruction references.

Also remove the duplicate SPP/LPP entry in the kernel disassembler
instruction list.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The s390 architecture is unique in respect to dirty page detection,
it uses the change bit in the per-page storage key to track page
modifications. All other architectures track dirty bits by means
of page table entries. This property of s390 has caused numerous
problems in the past, e.g. see git commit ef5d437f
"mm: fix XFS oops due to dirty pages without buffers on s390".

To avoid future issues in regard to per-page dirty bits convert
s390 to a fault based software dirty bit detection mechanism. All
user page table entries which are marked as clean will be hardware
read-only, even if the pte is supposed to be writable. A write by
the user process will trigger a protection fault which will cause
the user pte to be marked as dirty and the hardware read-only bit
is removed.

With this change the dirty bit in the storage key is irrelevant
for Linux as a host, but the storage key is still required for
KVM guests. The effect is that page_test_and_clear_dirty and the
related code can be removed. The referenced bit in the storage
key is still used by the page_test_and_clear_young primitive to
provide page age information.

For page cache pages of mappings with mapping_cap_account_dirty
there will not be any change in behavior as the dirty bit tracking
already uses read-only ptes to control the amount of dirty pages.
Only for swap cache pages and pages of mappings without
mapping_cap_account_dirty there can be additional protection faults.
To avoid an excessive number of additional faults the mk_pte
primitive checks for PageDirty if the pgprot value allows for writes
and pre-dirties the pte. That avoids all additional faults for
tmpfs and shmem pages until these pages are added to the swap cache.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Make use of the pfmf instruction, if available, to initialize storage keys
of whole 1MB or 2GB frames instead of initializing every single page with
the sske instruction.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

MACHINE_HAS_PFMF and MACHINE_HAS_HPAGE actually have the same semantics:
the cpu has the EDAT1 facility installed in zArch mode. So remove one
of the feature flags in machine_flags and rename the other one to EDAT1.

The two old macros simply get mapped to MACHINE_HAS_EDAT1.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

This implements the architecture backend for transparent hugepages
on s390.
Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Renaming the globally visible variable "user_mode" to "addressing_mode" in
order to fix a name clash was not a good idea. (Commit 37fe1d73 "s390/mm:
rename user_mode variable to addressing_mode")
Looking at the code after a couple of weeks one thinks: addressing mode of
what?
So rename the variable again. This time to s390_user_mode. Which hopefully
makes more sense.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Allow user-space processes to use transactional execution (TX).
If the TX facility is available user space programs can use
transactions for fine-grained serialization based on the data
objects that are referenced during a transaction. This is
useful for lockless data structures and speculative compiler
optimizations.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix name clash with user_mode() define which is also used in common code.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.

Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Replace __s390x__ with CONFIG_64BIT in all places that are not exported
to userspace or guarded with #ifdef __KERNEL__.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The store clock fast instruction saves a couple of instructions compared
to the store clock instruction. Always use stckf instead of stck if it
is available.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Disintegrate asm/system.h for S390.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: linux-s390@vger.kernel.org

In ESA mode STCKF is not defined even if the facility bit is enabled.
To prevent an illegal operation we must also check if we run a 64 bit kernel.
To make the check perform well add the STCKF bit to the machine flags.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move cpu topology facility detection to early setup code where it
should be.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use the SPP instruction to set a tag on entry to / exit of the virtual
machine context. This allows the cpu measurement facility to distinguish
the samples from the host and the different guests.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>

Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce the MACHINE_IS_LPAR flag for code that should only be
executed if Linux is running in an LPAR.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce user_mode to replace the two variables switch_amode and
s390_noexec. There are three valid combinations of the old values:
  1) switch_amode == 0 && s390_noexec == 0
  2) switch_amode == 1 && s390_noexec == 0
  3) switch_amode == 1 && s390_noexec == 1
They get replaced by
  1) user_mode == HOME_SPACE_MODE
  2) user_mode == PRIMARY_SPACE_MODE
  3) user_mode == SECONDARY_SPACE_MODE
The new kernel parameter user_mode=[primary,secondary,home] lets
you choose the address space mode the user space processes should
use. In addition the CONFIG_S390_SWITCH_AMODE config option
is removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Append scpdata to the kernel boot command line. If scpdata starts
with the equal sign (=), the kernel boot command line is replaced.
(For consistency with zIPL and IPL PARM parameters.)

To use scpdata for the kernel boot command line, scpdata must consist
of ascii characters only. If scpdata contains other characters,
scpdata is not appended to the kernel boot command line.
In addition, re-IPL is extended for setting scpdata for the next
Linux reboot.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently the storage of the machine flags is a globally exported unsigned
long long variable. By moving the storage location into the lowcore struct we
allow assembler code to check machine_flags directly even without needing a
register. Addtionally the lowcore and therefore the machine flags too will be
in cache most of the time.
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>