Add function to flush the sge ec context cache, and utilize
this new function in the driver
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Free VI interfaces in remove routine. If we don't do this then the
firmware will never drop the physical link to the peer.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet functionality is only available when working in ISSI > 0 mode.

Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs.

Now, once we have all the pre-steps in place, we can remove this limitation.

The last steps in the IB driver for getting that setup to work are:
create dummy SRQ for the driver's use (until now we could use XRC_SRQ
as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from
basic SRQs) and adapt the create QP function to be compatible with ISSI > 0.
Signed-off-by: NHaggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the following helpers:

1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port

These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now, mlx5_query_port_ptys always queried port number one.

Added new argument in the function's prototype so we can also query
the second port. This will be needed  when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two wrapper functions to the query adapter command:

1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.

2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
   query_adapter command.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added the implementation for the following commands:

1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT

They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.

Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The determination of the supported ISSI versions should be conditioned
on the returned mask, and not only on the return status of the query
ISSI command, fix that.
Signed-off-by: NHaggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).

Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: NHaggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some core helper functions were named with mlx5_ only prefix, fix that to
mlx5_core_ so we're aligned with the overall scheme used for core services.
Signed-off-by: NHaggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch afb736e9: "net/mlx5: Ethernet resource handling files"
from May 28, 2015, leads to the following static checker warning:

drivers/net/ethernet/mellanox/mlx5/core/en_flow_table.c:726 mlx5e_create_main_flow_table()
error: potential null dereference 'g'.  (kcalloc returns null)

Fixes: afb736e9 ("net/mlx5: Ethernet resource handling files")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.

We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.

With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove ethtool get/set support for wake on lan, adapter doesn't support
it.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support in ethtool to dump loopback port statistics
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support in ethtool to dump adapter channel stats
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool support to get adapter specific hardware statistics
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix typo in mlx4_set_vf_mac
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NCarol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NCarol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NCarol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code in drivers/net/ethernet/dec/tulip/uli526x.c
function "uli526x_timer":

  1086          } else
  1087                  if ((tmp_cr12 & 0x3) && db->link_failed) {
  [...snip...]
  1109                  }
  1110                  else if(!(tmp_cr12 & 0x3) && db->link_failed)
  1111                  {
  [...snip...]
  1117                  }
  1118                  db->init=0;

is misleadingly indented: the
  db->init=0
is indented as if part of the else clause at line 1086, but it is
independent of it (no braces before the "if" at line 1087).

This patch fixes the indentation to reflect the actual meaning of the code,
though is it actually meant to be part of the "else" clause?  (I'm a
compiler developer, not a kernel person).  It also adds spaces around
the assignment, to placate checkpatch.pl.

Seen via an experimental new gcc warning I'm working on for gcc 6,
-Wmisleading-indentation, using gcc r223098 adding
-Werror=misleading-indentation to KBUILD_CFLAGS in Makefile.
The experimental GCC emits this warning (as an error), rightly IMHO:

drivers/net/ethernet/dec/tulip/uli526x.c: In function ‘uli526x_timer’:
drivers/net/ethernet/dec/tulip/uli526x.c:1118:3: error: statement is
indented as if it were guarded by... [-Werror=misleading-indentation]
   db->init=0;
    ^
drivers/net/ethernet/dec/tulip/uli526x.c:1086:4: note: ...this ‘else’
clause, but it is not
  } else
     ^

Hope this is helpful
Dave
Signed-off-by: NDavid Malcolm <dmalcolm@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the TI dp83867 Gigabit ethernet phy
device.

The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the time_after_eq macro for jiffies comparison operation
Signed-off-by: NAntonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_RFS_ACCEL or SMP aren't set, we fail to build, fix it.

Also, avoid build warning as of unused function on that setup.

Fixes: c66fa19c ('net/mlx4: Add EQ pool')
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The condition under which the flush should occur was reversed.  The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.

If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.

To avoid breaking that feature, advertise only ciphers that the
hardware supports.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver is now ready to handle the -15.ucode.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add DC2DC_CONFIG_CMD (0x83) cmd.

Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.

The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmwares that used these commands is not supported
anymore. Remove them.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently, loading the firmware fails when it has higher API or CAPA
bits than the driver supports. That's an issue with integration.

At the same time, actually using api[0] and capa[0] will become
confusing when we also have api[1] and capa[1], and it's almost
certain that we'll mix up the bits and use the bits for api[1] with
api[0] by accident.

Avoid all this by translating the API/CAPA bits to the regular kernel
test_bit() format, and also providing wrapper functions. Also use the
__bitwise__ facility of sparse to check that we're testing the right
one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>