This is used by the I2C code in order to slow down the
speed to 20 kHz on devices with xc5000 or xc5000c.

So, it needs to be filled for all devices that use either
xc5000 or xc5000c.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Right now, the au0828 driver uses .tuner to detect if analog
tv is being used or not. By not filling .tuner fields at the
board struct, the I2C core can't do decisions based on it.

So, add a field to explicitly tell when analog TV is supported.

No functional changes.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This comment is already at the au0828-i2c where it belongs.
So, remove it from a board's entry. It doesn't make any sense
there, as we're setting the clock to 250kHz there, slowing it
down only at the au0828-i2c.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Instead of using printk(KERN_foo, use pr_foo() macros.

No functional changes.

Note: we should do the same for dprintk(), but that would
require to remove the dprintk levels. So, for now, let's
not touch on it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

HVR-850 also has a remote. Enable it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

HVR-950Q uses an I2C remote controller at address 0x47 (7-bits
notation). Add support for it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Commits 21dc61d3 and 7a1dd50b reduced the board I2C
speed to 20 MHz by default, due to a I2C stretch issue:
while xc5000 uses i2c stretch when a command is sent to it,
au0828 doesn't support this feature.

However, this is needed only for Xceive tuners. The other
I2C devices can work at the max speed.

So, revert the workarounds at board level, handling it at
I2C level, only when talking with xc5000.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.

Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Restructure the way we bring the various GPIOs out of reset.  In particular:

1.  we only need to setup the GPIOs as outputs once
2.  there's no point in writing 0x40 to register 0x00 since that's the EEPROM
    write protect and already it's configured as an input
3.  Separate out the act of enabling the power supply and bringing the tuner
    and demod out of reset.  If you don't then the chip may not be properly
    enabled (as the power supply is still ramping up when the chip comes
    out of reset).  This can result in probing failures.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Pull the analog frontend setup code out of au0828_card_setup into its
own seperate function, au0828_card_analog_fe_setup().
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch removes the dependendency of VIDEO_AU0828 on VIDEO_V4L2 by
creating a new Kconfig option, VIDEO_AU0828_V4L2, which enables analog
video capture support and depends on VIDEO_V4L2 itself.
With VIDEO_AU0828_V4L2 disabled, the driver will only support digital
television and will not depend on the v4l2-core. With VIDEO_AU0828_V4L2
enabled, the driver will be built with the analog v4l2 support included.
By default, the VIDEO_AU0828_V4L2 option will be set to Y, so as to
preserve the original behavior.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/usb/au0828/au0828-cards.c:28:6: warning: no previous prototype for 'hvr950q_cs5340_audio' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:161:6: warning: no previous prototype for 'au0828_uninit_isoc' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:200:5: warning: no previous prototype for 'au0828_init_isoc' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:786:5: warning: no previous prototype for 'au0828_analog_stream_enable' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:813:6: warning: no previous prototype for 'au0828_analog_stream_reset' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:916:6: warning: no previous prototype for 'au0828_vid_buffer_timeout' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:940:6: warning: no previous prototype for 'au0828_vbi_buffer_timeout' [-Wmissing-prototypes]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The hack I put in a couple of years ago to avoid clock stretching issues
when talking to the xc5000 worked fine for writes, but intermittently
fails for register reads, because the xc5000 may stretch the clock for
longer between bytes (I was seeing cases of 21 us on the analyzer).

The problem manifested itself as the xc5000 firmware version and PLL
lock register intermittently showing garbage values.

Slow down the i2c bus from 30 KHz to 20 KHz to accommodate.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested with Yfeng 680 ATV dongle.
Signed-off-by: NIsmael Luceno <ismael.luceno@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

tuner-core has no business to do with digital TV. So, don't use
T_DIGITAL_TV on it, as it has no code to distinguish between
them, and nobody fills T_DIGITAL_TV right.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The argument isn't used anymore by the functions, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.

All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.

This simplifies this API substantially.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The xc5000 datasheet indicates that the reset pin only needs to be held low
for 10ms.  Reduce the value accordingly, which speeds up the firmware load
time a bit.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Setup the i2c clock speed to be definable on a per-board basis.  This allows
us to explicitly set the clock speed to 30 KHz on the 950q, and also gets rid
of code which sets it on a basis of what chip the i2c master is talking to
at any given time (which could have caused issues because i2c slaves should
never receive commands at a clock higher than their supported clock speed).
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Per Hans Verkuil <hverkuil@xs4all.nl> instruction, remove the deprecated
attach_inform/detach_inform routines, and convert over the i2c calls to
subdev calls.

Thanks to Hans Verkuil <hverkuil@xs4all.nl> for providing feedback on the
au0828 analog support.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Take a pass over all of the au0828/au8522 files and cleanup all the codingstyle
issues.  This patch does not make *any* functional change to the code.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert over to using the new subdev framework for the au0828 bridge.  This
includes using the new i2c probing mechanism.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is not valid to look for dev->board.input == NULL to detect an undefined
analog configuration section, since it is a member of the struct and not a
pointer (hence it will *always* be non-NULL).  Do the check based on whether
the first input is actually a valid input type instead.

Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing sample hardware
of various configurations to test with.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rework the way boards are managed so that we can change the board description
based on the Hauppauge eeprom (modeled after cx88-cards.c).

Also, make sure that we don't load the analog stack if there are no analog
inputs defined in the board profile.

Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing information on
the various ways different Hauppauge boards can be configured.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the analog parameters to the device profile for the HVR-850

Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the analog functionality found in the au0828 bridge

Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix compilation by adding linux/version.h]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

au0828: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add autodetection support for a new revision of the Hauppauge HVR950Q (2040:721e)
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>