Management firmware is used as an arbiter between the various PFs
in regard to loading - it causes the various PFs to load/unload
sequentially and informs each of its appropriate rule in the init.

But the existing flow is too weak to handle some scenarios where
PFs aren't properly cleaned prior to loading.
The significant scenarios falling under this criteria:
  a. Preboot drivers in some environment can't properly unload.
  b. Unexpected driver replacement [kdump, PDA].

Modern management firmware supports a more intricate loading flow,
where the driver has the ability to overcome previous limitations.
This moves qed into using this newer scheme.

Notice new scheme is backward compatible, so new drivers would
still be able to load properly on top of older management firmwares
and vice versa.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We'll soon need additional information, so start by changing
the infrastructure to receive the initializing variables
via a parameter struct.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware is used as arbiter between different PFs
which are loading/unloading, but in order to use the synchronization
it offers the contending configurations need to be applied either
between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE
management firmware commands.

Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and
qed_hw_reset() which don't abide this requirement; Most of the closure
is doing outside the scope of the unload request.

This patch removes qed_hw_reset() and places the relevant stop
functionality underneath the management firmware protection.
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver must not access the two fields directly but should instead use
the helper functions to set the values and keep a consistent internal
state:

ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
ethernet/stmicro/stmmac/stmmac_main.c:4083:8: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?

Fixes: a8f5102a ("net: stmmac: TX and RX queue priority configuration")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement dpipe's table ops for erif table which provide:
1. Getting the entries in the table with the associate values.
	- match on "mlxsw_meta:erif_index"
	- action on "mlxsw_meta:forwared_out"
2. Synchronize the hardware in case of enabling/disabling counters which
   mean removing erif counters from all interfaces.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rif helper function to access the rif index and rif devices ifindex.
This functions will be used by dpipe in order to dump the rif table.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for counter allocation on router interfaces. The allocation
depends on the counter state of relevant table. In case the counting is
disabled or no counters left the counter index will be set as invalid.

Also a counter pool for router allocation is added.
Signed-off-by: NArakdi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RICNT register retrieves per port performance counter. It will be
used to query the router interfaces statistics.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add definition for egress router interface table. This table describes
the final part in the routing pipeline. This table matches the egress
interface index (rif index, which is set by the previous stages and
determine the out port) and makes the decision of forwarding the packet
towards the L2 logic or dropping it.

The metadata header is added to represent this internal information.
The rif index field is mapped logically to netdevice ifindex.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update RITR for counter support. This allows adding counters for
ASIC's router ports.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Probably due to some mis-merging fix a bug associated with commits
d7ce6422 ("i40e: don't check params until after checking for client
instance", 2017-02-09) and 3140aa9a78c9 ("i40e: KISS the client
interface", 2017-03-14)

The first commit tried to move the initialization of the params
structure so that we didn't bother doing this if we didn't have a client
interface. You can already see that it looks fishy because of the
indentation. The second commit refactors a bunch of the interface, and
incorrectly drops the params initialization.

I believe what occurred is that internally the two patches were
re-ordered, and the merge conflicts as a result were performed
incorrectly.

Fix the use of an uninitialized variable by correctly initializing the
params variable via i40e_client_get_params().
Reported-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VSI is being dereferenced before the VSI null check; if VSI is
null we end up with a null pointer dereference.  Fix this by
performing VSI deference after the VSI null check.  Also remove
the need for using adapter by using vsi->back->cinst.

Detected by CoverityScan, CID#1419696, CID#1419697
("Dereference before null check")

Fixes: ed0e894d ("i40evf: add client interface")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.

Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago.  It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.

Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a minor clean-up to make the i40e/i40evf process_skb_fields
function look a little more like what we have in igb.  The Rx checksum
function called out a need for skb->protocol but I can't see where it
actually needs it.  I am assuming this is something that was likely
refactored out some time ago as the Rx checksum code has gone through a few
rewrites.

Change-ID: I0b4668a34d90b61b66ded7c7c26e19a3e2d06251
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed no longer needed delays.  At preproduction stage those delays were
needed but now these delays are not needed.
Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

First, this patch eliminates IOMMU DMAR Faults caused by VF hardware.
This is done by enabling VF hardware only after VSI resources are
freed. Otherwise, hardware could DMA into memory that is (or just has
been) being freed.

Then, the VF driver is activated only after VSI resources have been
reallocated. That's because the VF driver can request resources
immediately after it's activated. So they need to be ready at that
point.

The second race condition happens when the OS initiates a VF reset,
and then before it's finished modifies VF's settings by changing its
MAC, VLAN ID, bandwidth allocation, anti-spoof checking, etc. These
functions needed to be blocked while VF is undergoing reset. Otherwise,
they could operate on data structures that had just been freed or not
yet fully initialized.

Change-ID: I43ba5a7ae2c9a1cce3911611ffc4598ae33ae3ff
Signed-off-by: NRobert Konklewski <robertx.konklewski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to reset skb back to NULL when we have freed it in the Rx cleanup
path.  I found one spot where this wasn't occurring so this patch fixes it.

Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.

Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time.  The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.

I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff".  By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.

Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ibmvnic driver keeps its statistics in net_device->stats, so the
net_stats member in struct ibmvnic_adapter is unused. Remove it.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ibmveth driver keeps its statistics in net_device->stats, so the
stats member in struct ibmveth_adapter is unused. Remove it.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bfin_mac driver keeps its statistics in net_device->stats, so the
stats member in struct bfin_mac_local is unused. Remove it, as well as
the accompanying comment.

Cc: adi-buildroot-devel@lists.sourceforge.net
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new fail-safe channels switch mechanism to set new
netdev mtu and lro settings.

MTU and lro settings demand some HW configuration changes after new
channels are created and ready for action. In order to unify switch
channels routine for LRO and MTU changes, and maybe future configuration
features, we now pass to it a modify HW function pointer to be
invoked directly after old channels are de-activated and before new
channels are activated.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Use the new fail-safe channels switch mechanism to set up new
tc parameters.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Use the new fail-safe channels switch mechanism to set new
CQE compressing and CQE moderation mode settings.

We also move RX CQE compression modify function out of en_rx file  to
a more appropriate place.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Use the new fail-safe channels switch mechanism to set new ethtool
settings:
 - ring parameters
 - coalesce parameters
 - tx copy break parameters
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

A fail safe helper functions that allows switching to new channels on the
fly,  In simple words:

make_new_config(new_params)
{
    new_channels = open_channels(new_params);
    if (!new_channels)
         return "Failed, but current channels are still active :)"

    switch_channels(new_channels);

    return "SUCCESS";
}

Demonstrate mlx5e_switch_priv_channels usage in set channels ethtool
callback and make it fail-safe using the new switch channels mechanism.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

mlx5e_redirect_rqts_to_{channels,drop} and mlx5e_{add,del}_sqs_fwd_rules
and Set real num tx/rx queues belong to
mlx5e_{activate,deactivate}_priv_channels, for that we move those functions
and minimize mlx5e_open/close flows.

This will be needed in downstream patches to replace old channels with new
ones without the need to call mlx5e_close/open.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Remove mlx5e_priv pointer from CQ and RQ structs,
it was needed only to access mdev pointer from priv pointer.

Instead we now pass mdev where needed.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

In order to have a clean separation between channels resources creation
flows and current active mlx5e netdev parameters, make sure each
resource creation function do not access priv->params, and only works
with on a new fresh set of parameters.

For this we add "new" mlx5e_params field to mlx5e_channels structure
and use it down the road to mlx5e_open_{cq,rq,sq} and so on.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

As a foundation for safe config flow, a simple clear API such as
(Open then Activate) where the "Open" handles the heavy unsafe
creation operation and the "activate" will be fast and fail safe,
to enable the newly created channels.

For this we split the RQs/TXQ SQs and channels open/close flows to
open => activate, deactivate => close.

This will simplify the ability to have fail safe configuration changes
in downstream patches as follows:

make_new_config(new_params)
{
     old_channels = current_active_channels;
     new_channels = create_channels(new_params);
     if (!new_channels)
              return "Failed, but current channels still active :)"
     deactivate_channels(old_channels); /* Can't fail */
     activate_channels(new_channels); /* Can't fail */
     close_channels(old_channels);
     current_active_channels = new_channels;

     return "SUCCESS";
}
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Rename mlx5e_refresh_tirs_self_loopback to mlx5e_refresh_tirs,
as it will be used in downstream (Safe config flow) patches, and make it
fail safe on mlx5e_open.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

RQ Tables are always created once (on netdev creation) pointing to drop RQ
and at that stage, RQ tables (indirection tables) are always directed to
drop RQ.

We don't need to use mlx5e_fill_{direct,indir}_rqt_rqns to fill the drop
RQ in create RQT procedure.

Instead of having separate flows to redirect direct and indirect RQ Tables
to the current active channels Receive Queues (RQs), we unify the two
flows by introducing mlx5e_redirect_rqt function and redirect_rqt_param
struct. Combined, they provide one generic logic to fill the RQ table RQ
numbers regardless of the RQ table purpose (direct/indirect).

Demonstrated the usage with mlx5e_redirect_rqts_to_channels which will
be called on mlx5e_open and with mlx5e_redirect_rqts_to_drop which will
be called on mlx5e_close.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Have a dedicated "channels" handler that will serve as channels
(RQs/SQs/etc..) holder to help with separating channels/parameters
operations, for the downstream fail-safe configuration flow, where we will
create a new instance of mlx5e_channels with the new requested parameters
and switch to the new channels on the fly.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

To simplify mlx5e_open_locked flow we set netdev->rx_cpu_rmap on netdev
creation rather on netdev open, it is redundant to set it every time on
mlx5e_open_locked.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Instead of iterating over the channel SQs to set their max rate, do it
on SQ creation per TXQ SQ.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>

Currently the return allocated index and err value are multiplexed.
This patch changes the API to decouple the ret value from the allocated
index.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>