If NetworkManager is busy scanning when user
tries to unload the module, the driver can not be unloaded
because HW still scanning.

Make sure driver sends abort scan host command to uCode if it
is in the middle of scanning during driver unload.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix following error by sending synchronous command and waiting for the command
to complete.

mac80211-phy0: failed to remove key (0, ff:ff:ff:ff:ff:ff) from hardware (-16).

-16 is EBUSY error. The asynchronous command tests for STATUS_EXIT_PENDING
while interface is getting down and it returns -EBUSY error if set.
Changing the host command from asynchronous call to synchronous call
enables command to be run while interface is going down.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For 6000 series and up, additional enhanced regulatory tx power
limitation information is added to EEPROM image.

In order to setup the tx power limitation per channel correctly. Read
the enhanced tx power information from EEPROM image and update
accordingly.

The information is provided per SISO (a,b,c) chain based, it also has
information for both MIMO2 and MIMO3. For tx power regulatory
limitation, take the highest number from all the chains and update.
Also update tx_power_user_lmt to the highest power supported by any
channels and chains
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove duplicated define "STA_FLG_PWR_SAVE_MSK"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add code to set the HT flags (HT, 40 MHz, Short guard interval) in
the ieee80211_rx_status field passed to mac80211.  This ensures that mac80211
processes these HT packets correctly.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clear the flags (most importantly, the IEEE80211_TX_RC_MCS flag)
when sending a non-HT packet so that the rate index can be properly treated.
This fixes the reporting of legacy rates in wireless-extensions for packets
sent after an HT packet.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

debugFs file show current tx power for all the transmit chains

Adding "tx_power" file in /sys/kernal/debug/ieee80211/phy0/iwlagn/debug
to display current tx power for all the active chains in 1/2 dB step.

Show tx power information "Not available" if uCode can not provide the
information or interface is down.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

uCode version changed to v4 for 6000 series

The additional parameter added to v4 is providing current tx power for
each chain in tx statistics portion of "statistics notification"
command.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Perform error checking and report failure when setting tx power from
sysfs.
If fail to set the tx power, do not update the local copy, so user will
not see the incorrect tx power in sysfs
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changing the name from "tx_power_channel_lmt" to "tx_power_device_lmt";
to give idea that scope of limit is for overall device, not any
individual channels
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When setting tx power in sysfs, check against max channel tx power
limit instead of IWL_TX_POWER_TARGET_POWER_MAX.

Different devices have different max tx power limit; using
IWL_TX_POWER_TARGET_POWER_MAX can excess the limitaion and give wrong
information.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the tx_power_user_lmt to the lowest power level
this value will get overwritten by channel's max power avg
from eeprom
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 1ccb84d87d04df3c76cd4352fe69786d8c7cf016 by Wey-Yi Guy
("iwlwifi: clean up unused NL80211_IFTYPE_MONITOR for Monitor mode")
broke injection of non-broadcast frames to unassociated stations
(causing a SYSASSERT for all such injected frames), due to injected
frames no longer automatically getting a broadcast station ID assigned.
This patch restores the old behavior, fixing the aforementioned
regression.

Also, consistently check for IEEE80211_TX_CTL_INJECTED instead of
iwl_is_monitor_mode in the TX path, as TX_CTL_INJECTED specifically
means that a given packet is coming from a monitor interface, while
iwl_is_monitor_mode only shows whether a monitor interface exists
on the device.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The CF8305 is a very old silicon running firmware version 3.0 . This card also
needs some special treatment as it's so old it can't do unaligned register
access. But since that happens only at one place, there were no changes made to
the register access functions, but instead that particular place was fixed.
Also, this card uses only one-stage firmware which is loaded the same way as
helper firmware. The second-stage firmware isn't loaded on this card and doesn't
therefore have to be supplied.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clarify what the heck the function is doing with better variable names
and less indirection and better comments.  Also ensure callers use the
proper minimum size, even though all rates arrays should be size
MAX_RATES anyway.  Reverts part of Andrey's dynamic alloc patch since we
don't really need it.  Also leaves the passed-in rates array alone on
errors.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element.

(also includes "Libertas: Association request to the driver failed"

The size of the tmp buffer was too small, causing a regression

rates->rates has an arraysize of 1, so a memcpy with
MAX_RATES (14) was already causing reads out of bounds.

In get_common_rates() the memset/memcpy can be moved upwards. -- JWL)
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Tested-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed that the throughput field of the minstrel_rate struct is never used,
so remove it.
Signed-off-by: NArnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to the way the tasklets work in mac80211 there's
no need to ever disable them.

However, we need to clear the pending packets when
taking down the last interface because otherwise
the tx_pending_tasklet might be queued if the
driver mucks with the queues (which it shouldn't).

I've had a situation occasionally with ar9170 in
which ksoftirq was using 100% CPU time because
a disabled tasklet was scheduled, and I think that
was due to ar9170 receiving a packet while the
tasklet was disabled. That's strange and it really
should not do that for other reasons, but there's
no need to waste that much CPU time over it, it
should just warn instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the interface type changes while connected, and the
driver does not require the interface to be down for a
type change, it is currently possible to get very strange
results unless the driver takes special care, which it
shouldn't have to.

To fix this, take care to disconnect/leave IBSS when
changing the interface type -- even if the driver may fail
the call. Also process all events that may be pending to
avoid running into a situation where an event is reported
but only processed after the type has already changed,
which would lead to missing events and warnings.

A side effect of this is that you will have disconnected
or left the IBSS even if the mode change ultimately fails,
but since the intention was to change it and thus leave or
disconnect, this is not a problem.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bob reported that he got warnings in IBSS mode about
the ssid_len being zero on a joined event, but only
when kmemcheck was enabled. This appears to be due
to a race condition between drivers and userspace,
when the driver reports joined but the user in the
meantime decided to leave the IBSS again, the warning
would trigger. This was made more likely by kmemcheck
delaying the code that does the check and sends the
event.

So first, make the warning trigger closer to the
driver, which means it's not locked, but since only
the warning depends on it that's ok.

And secondly, users will not want to have spurious
warnings at all, so make those that are known to be
racy in such a way configurable.
Reported-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX/RX chainmasks were set to 1x1 during scanning.
Configure them properly with the values retrieved from
the EEPROM.

Also, this requires scan_start/scan_end callbacks to be
locked with sc->mutex.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This eliminates the dual definition of ieee80211_channel (and possibly
others), further clarifying who defines what and paving the way for
inclusion of cfg80211.h.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we lose a scan, cfg80211 tries to clean up after
the driver. However, it currently does this too early,
it does this in GOING_DOWN already instead of DOWN, so
it may happen with mac80211. Besides fixing this, also
make it more robust by leaking the scan request so if
the driver later actually finishes the scan, it won't
crash. Also check in ___cfg80211_scan_done whether a
scan request is still pending and exit if not.
Reported-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add_wep_key() tries to check if key length is not 5 AND not 13
but uses (key_len != 5 || key_len != 13) instead. Fix this.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since configure_filter can sleep now, any multicast
configuration needed to be postponed to a work struct.
This, however, lead to a problem that we could queue
the work, stop the device and then afterwards invoke
configure_filter which may lead to driver hangs and is
a bug. To fix this, we can just cancel the filter work
since it's unnecessary to do after stopping the hw.

Since there are various places that call drv_stop, and
two of them do very similar things, the code for them
can be put into a shared function at the same time.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reported-by: NLennert Buytenhek <buytenh@wantstofly.org>
Tested-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support for FIF_OTHER_BSS was missing.  This patch adds support for this
filtering mode which in turn resolves a problem where mesh interfaces would not
receive broadcast traffic.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mesh config information element has changed significantly since draft 1.08
This patch brings it up to date.

Thanks to Sam Leffler and Rui Paulo for identifying this.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch "mac80211: fix PS-poll response race" somehow broke
broadcast buffering in a funny way.

During normal operation - stations are awake - the firmware refused
to transmit broadcast frames and reported P54_TX_PSM_CANCELLED.
But everything worked as soon as one station entered PSM.

The reason:
The stack sets IEEE80211_TX_CTL_SEND_AFTER_DTIM for outgoing
broadcast frames as soon as a station is marked as sleeping.
This flag triggers a path which will reroute these frames
into p54's "content after beacon" queue, which is designed
to cope with the demands for psm.

This patch restores the old behavior.

IEEE80211_TX_CTL_CLEAR_PS_FILT will once again be used to signalize
the firmware to ignore the ps canceling for certain frames.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If nothing has been written into the qeth sysfs-attribute layer2,
its value is "-1" meaning "not yet defined". But the value is
displayed as "1" meaning "layer2 selected". The patch changes the
reading of this "-1"-value to "-1" to make clear the layer2-attribute
has not yet been defined.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth displayed an entry in /proc/service_level even when no valid
MCL-string was available (the MCL info is blank). The change is to
create an entry in /proc/service_level only when MCL-string is
non-zero.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear separation of cast-type determination (send path) for layer-2
resp. layer-3. Allowing to have inline functions for qeth layer-
discipline.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the IP address list contains entries (not removed when the device was set
offline) this entries should be registered next time the device is brought online.
In the past this was done implicitly with the device open call but since we wait
in the set IPv4 IPA and the device open common code holds various locks this
does not work any longer.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Qeth HiperSockets support now retries sending of packets when the
IBM System z signals a temporary resource shortage (e.g. target
buffer full). The packet is enqueued into the device queue.
After 3 times of unsuccessful send the packet is dropped.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steven Rostedt has suggested that Neil work with the tracing
folks, trying to use TRACE_EVENT as the mechanism for
implementation.  And if that doesn't workout we can investigate
other solutions such as that one which was tried here.

This reverts the following 2 commits:

5a165657
("net: skb ftracer - Add config option to enable new ftracer (v3)")

9ec04da7
("net: skb ftracer - Add actual ftrace code to kernel (v3)")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.100.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the AC131 fast ethernet transceiver.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the BCM50610M phy ID.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>