Only disable the pipe if the monitor is physically
disconnected.  The previous logic also disabled the
pipe if the link was trained.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41248Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The previous code could potentially loop forever.  Limit
the number of DP aux defer retries to 4 for native aux
transactions, same as i2c over aux transactions.

Noticed by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: Brad Campbell <lists2009@fnarfbargle.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

An incorrect ordering in the error checking code lead
to DP aux defer being skipped in the aux native write
path.  Move the bytes transferred check (ret == 0)
below the defer check.

Tracked down by: Brad Campbell <brad@fnarfbargle.com>

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41121Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: Brad Campbell <brad@fnarfbargle.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set.  Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 18b4fada.

This code was correct, apologies to anyone who noticed things broke.

revert contents are different due to another commit in between.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Make the default FBC behaviour chipset specific, allowing us to turn
it on by default for Ironlake and older where it has been seen to
cause trouble with screen updates.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NFrancis Moreau <francis.moro@gmail.com>

I was seeing a nasty 5 frame glitch every 10 seconds, caused by the
poll for connection on DVI attached by SDVO.

As my SDVO DVI supports hotplug detect interrupts, the fix is to
enable them, and hook them in to the various bits of driver
infrastructure so that they work reliably.

Note that this is only tested on single-function DVI-D SDVOs, on two
platforms (965GME and 945GSE), and has not been checked against a
specification document.

With lots of help from Adam Jackson <ajax@redhat.com> on IRC.
Signed-off-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.

The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reported-by: NOliver Hartkopp <socketcan@hartkopp.net>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>

The BO blit code inconsistenly handled the page size.  This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well.  Switch the driver blit callbacks to take num pages in GPU
page units.

Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.

v2: incorporate suggestions from Michel.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

cur_pages is the number of pages per loop iteration.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Should fix https://bugzilla.redhat.com/show_bug.cgi?id=726277 .
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Apparently this doesn't always work reliably, e.g. at resume time.

Just initialize to 0, so the ring is considered empty.

Tested with hibernation on Sumo and Cayman cards.

Should fix https://bugs.launchpad.net/ubuntu/+source/linux/+bug/820746/ .
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes an information leak to userspace, we were handing out un-zeroed pages
for any newly created TTM_PL_TT buffer.
Reported-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Tested-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Remove the duplicate "return" statement in drm_fb_helper_panic().
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This commit resolves a possible 'NULL pointer dereference'
It uses the same approach as radeon, intel and nouveau/nv50

Fixes bug 'Nouveau: Kernel oops when unplugging external monitor'
https://bugs.freedesktop.org/show_bug.cgi?id=40336Signed-off-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

nv04_sgdma_bind binds the same page multiple times on
architectures where PAGE_SIZE != 4096.
Let's fix it.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Not cleaning after alloc failure would result in crash on destroy,
because nouveau_sgdma_clear assumes "ttm_alloced" to be not null when
"pages" is not null.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes possbile NULL pointer dereference
Resolves 'kernel crash in nv50_crtc_do_mode_set_base during shutdown'
https://bugs.freedesktop.org/show_bug.cgi?id=40005Signed-off-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Sink type is always DP for DP bridges and EDID fetch on
DP bridges is always i2c over aux rather than plain i2c.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If the bios or OS sets the pci max read request size to 0 or an
invalid value (6,7), it can result in a hang or slowdown.  Check
and set it to something sane if it's invalid.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=42162

v2: use pci reg defines from include/linux/pci_regs.h
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On some Power rv100 cards, we have no ATY OF table, but we have
no combios table either, and hence we refuse all modes on VGA-0
since we end up with a 0 max pixel clock.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>

Fixes resume on Compaq Presario V5245EU.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=41642Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

For some reason SPI block is in broken state after module
unloading. This lead to broken rendering after reloading
module. Fix this by reseting SPI block in CP resume function

Signed-off-by: Jerome Glisse <jglisse@redhat.com
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

It is left out the code to decrease the number of connector and encoder
to the cleanup functions.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise it just contains random memory.

Issue detected by cppcheck.
Signed-off-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Toshiba Satellite L300D with ATI Mobility Radeon X1100 sends data
   to i2c bus for a HDMI connector that is not implemented/existent
   on the notebook's board.

   Fix by applying extented DDC probing for this connector.

   Requires [PATCH] drm/radeon: Extended DDC Probing for Connectors
   with Improperly Wired DDC Lines

   Tested for kernel 2.6.38 on Toshiba Satellite L300D notebook

   BugLink: http://bugs.launchpad.net/bugs/826677Signed-off-by: NThomas Reim <reimth@gmail.com>
Acked-by: NChris Routh <routhy@gmail.com>
Cc: <stable@kernel.org>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This was true for new TTM_PL_SYSTEM and new TTM_PL_TT cases, but wasn't
the case on TTM_PL_SYSTEM<->TTM_PL_TT moves, which causes trouble on some
paths as nouveau's move_notify() hook requires that the dma addresses be
valid at this point.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Nouveau makes the assumption that if a TTM is bound there will be a mm_node
around for it and the backwards ordering here resulted in a use-after-free
on some eviction paths.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

ttm_tt_destroy kfrees passed object, so we need to nullify
a reference to it.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@kernel.org
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The commit "Not all systems expose a firmware or platform mechanism for
changing the backlight intensity on i915, so add native driver support"
adds calls to  intel_panel_setup_backlight() from intel_{lvds,dp}_init
so do not call it again from intel_setup_outputs().

BugLink: http://bugs.launchpad.net/bugs/831542Signed-off-by: NKamal Mostafa <kamal@canonical.com>
ACKed-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise these would need to be painstakingly calculated looking at the source
code.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Alpha needs to have available the system bus address for the Radeon's
local memory, so that it can be used in ttm_bo_vm_fault(), when building
the PTEs for accessing that VRAM.  So, we make bus.addr hold the ioremap()
return, and then we can modify bus.base appropriately for use during page
fault processing.
Signed-off-by: NJay Estabrook <jay.estabrook@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command.  However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL.  Since we're not doing that yet, go
back to the old default so things work.

v2: don't forget to actually *clear* the new bit
Reviewed-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The clock gating functions are only assigned under KMS, so don't try
to call them under UMS.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NJustin P. Mattock <justinmattock@gmail.com>

Disable this feature when KMS is not running by setting the
driver->get_vblank_timestamp function pointer to NULL.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NJustin P. Mattock <justinmattock@gmail.com>

Not all systems expose a firmware or platform mechanism for changing the backlight intensity on i915, so add native driver support.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NSedat Dilek <sedat.dilek@googlemail.com>
Tested-by: NMichel Alexandre Salim <salimma@fedoraproject.org>
Tested-by: NKamal Mostafa <kamal@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Attempting to try and turn off disconnected display hw in the
hotput handler lead to more problems than it helped.  For
now just register an event and only attempt the do something
interesting with DP.  Other connectors are just too problematic:
- Some systems have an HPD pin assigned to LVDS, but it's rarely
if ever connected properly and we don't really care about hpd
events on LVDS anyway since it's always connected.
- The HPD pin is wired up correctly for eDP, but we don't really
have to do anything since the events since it's always connected.
- Some HPD pins fire more than once when you connect/disconnect
- etc.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39882Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>