This patch fixes a number of bugs in the authentication process:

1) When falling back to Shared Key authentication mode from Open System,
a missing 'return' would cause the auth request to be sent, but would
drop the card into Management Error state.  When falling back, the
driver should also indicate that it is switching to Shared Key mode by
setting exclude_unencrypted.

2) Initial authentication modes were apparently wrong in some cases,
causing the driver to attempt Shared Key authentication mode when in
fact the access point didn't support that mode or even had WEP disabled.
The driver should set the correct initial authentication mode based on
wep_is_on and exclude_unencrypted.

3) Authentication response packets from the access point in Open System
mode were getting ignored because the driver was expecting the sequence
number of a Shared Key mode response.  The patch separates the OS and SK
mode handling to provide the correct behavior.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previous patch that added ENCODEEXT and AUTH support to the atmel
driver contained a slight error which would cause just setting the TX
key index to also set the encryption key again.  This patch allows any
combination of setting the TX key index and setting an encryption key.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NKurt Hackel <Kurt.Hackel@oracle.com>
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>

Disable automatic checkpointing of the journal - this is a relic from older
ocfs2 days. Worth quite a bit of performance on longer running single node
tests.
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>

* fix a hang in recovery that occurred in dlmlock_remote.  the $RECOVERY
  lock was never moved to the granted queue even after getting DLM_NORMAL
  back from the master node.
Signed-off-by: NKurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>

* add dlm_wait_for_node_death function to be used after receiving a network
  error.  this will wait for the given timeout to allow the heartbeat
  callbacks to update the domain map.  without this, some paths may spin
  and consume enough cpu that the heartbeat gets starved and never updates.
Signed-off-by: NKurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>

* fix a bug in dlm_convert_lock_handler where dlm_lockres_release_ast was
  being called even if no ast was ever reserved
Signed-off-by: NKurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>

* after successfully taking the $RECOVERY lock in EX mode, recheck to make
  sure that recovery has not already begun or completed on another node
Signed-off-by: NKurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: NMark Fasheh <mark.fasheh@oracle.com>

If a tag is set for a node being deleted from a radix_tree, then that
tag gets cleared from the parent of the node, even if it is set for some
siblings of the node begin deleted.

This patch changes the logic to include a test for any_tag_set similar
to the logic a little futher down.  Care is taken to ensure that
'nr_cleared_tags' remains equals to the number of entries in the 'tags'
array which are set to '0' (which means that this tag is not set in the
tree below pathp->node, and should be cleared at pathp->node and
possibly above.

[ Nick says: "Linus FYI, I was able to modify the radix tree test
  harness to catch the bug and can no longer trigger it after the fix.
  Resulting code passes all other harness tests as well of course." ]
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Mention the "pci=nommconf" option in kernel-parameters.txt.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I get about 88 squillion of these when suspending an old ad450nx server.

Cc: Pavel Roskin <proski@gnu.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The early initialization of cpu_to_node code as it is now only updates the
cpu_to_node array, and does not update cpu_pda()->nodemember.  This will
cause numa_node_id() to return 0 on systems where CPU 0 is not on Node 0.
This leads to a kernel panic in slab.c.

I've tested the patch below on a 16 processor x86_64 ES7000-600 server, and
no longer see the panic I saw with the original 2.6.16-rc3.
Signed-off-by: NDan Yeisley <dan.yeisley@unisys.com>
Acked-by: NAndi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

For two macros the arguments were expanded twice, change them to inline
functions to avoid it.
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches.  The idea is to make it possible to use them portably even before
distros include them in libc headers.

Move common flags to asm-generic/mman.h
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a latent bug in cpuset_exit() handling.  If a task tried to allocate
memory after calling cpuset_exit(), it oops'd in
cpuset_update_task_memory_state() on a NULL cpuset pointer.

So set the exiting tasks cpuset to the root cpuset instead of to NULL.

A distro kernel hit this with an added kernel package that had just such a
hook (allocating memory) in the exit code path.
Signed-off-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We're getting some softlockup false positives during heavy PIO operations.  So
poke the lockup detector.

Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Commit 296e0855:

    "kbuild: fix make -jN with multiple targets with O=..."

causes a ~95% increase in build time for the kernel.  Before: 4m21s
after: 8m1.403s.  Can we revert this until another approach is found?

Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There were two mistakes in the register-read-on-(un)blank approach.

- First, without proper register (un)locking the value read back will always
  be zero, and this is what I missed entirely until just now.  Due to this,
  the logic could not be verified at all and I tried some bogus checks which
  are completely stupid.

- Second, the LCD status bit will always be set to zero when the backlight
  has been turned off.  Reading the value back during unblank will disable the
  LCD unconditionally, regardless of the state it is supposed to be in, since
  we set it to zero beforehand.

So this is what we do now:

- create a new variable in struct neofb_par, and use that to determine
  whether to read back registers (initialized to true)

- before actually blanking the screen, read back the register to sense any
  possible change made through Fn key combo

- use proper neoUnlock() / neoLock() to actually read something

- every call to neofb_blank() determines if we read back next time: blanking
  disables readback, unblanking (FB_BLANK_UNBLANK) enables it

This should give us a nice and clean state machine.  Has been thoroughly
tested on a Dell Latitude CPiA / NM220 Chip docked to a C/Dock2 with attached
CRT in all possible combinations of LCD/CRT on/off.  I changed the config via
Fn key, let the console blank, unblanked by keypress - works flawlessly.
Signed-off-by: NChristian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If skb->ip_summed is CHECKSUM_HW here, skb->csum includes checksum
of actual IPv6 header and extension headers. Then such excess
checksum must be subtruct when nf_conntrack calculates TCP/UDP checksum
with pseudo IPv6 header. Spotted by Ben Skeggs.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Locally generated ICMPv6 errors should be associated with the conntrack
of the original packet. Since the conntrack entry may not be in the hash
tables (for the first packet), it must be manually attached.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP RSTs generated by the REJECT target should be associated with the
conntrack of the original TCP packet. Since the conntrack entry is
usually not is the hash tables, it must be manually attached.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move registration of __nf_ct_attach to nf_conntrack_core to make it usable
for IPv6 connection tracking as well.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NF_CONNTRACK_MARK is bool and depends on NF_CONNTRACK which is
tristate.  If a variable depends on NF_CONNTRACK_MARK and doesn't take
care about NF_CONNTRACK, it can be y even if NF_CONNTRACK isn't y.
NF_CT_ACCT have same issue, too.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nf_hook() is supposed to call the netfilter hook and return control of the
packet back to the caller in case it may pass, the okfn is only used for
queueing.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a packet matching an IPsec policy is SNATed so it doesn't match any
policy anymore it looses its xfrm bundle, which makes xfrm4_output_finish
crash because of a NULL pointer dereference.

This patch directs these packets to the original output path instead. Since
the packets have already passed the POST_ROUTING hook, but need to start at
the beginning of the original output path which includes another
POST_ROUTING invocation, a flag is added to the IPCB to indicate that the
packet was rerouted and doesn't need to pass the POST_ROUTING hook again.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. The tracee can go from ptrace_stop() to do_signal_stop()
   after __ptrace_unlink(p).

2. It is unsafe to __ptrace_unlink(p) while p->parent may wait
   for tasklist_lock in ptrace_detach().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

copy_process:

	attach_pid(p, PIDTYPE_PID, p->pid);
	attach_pid(p, PIDTYPE_TGID, p->tgid);

What if kill_proc_info(p->pid) happens in between?

copy_process() holds current->sighand.siglock, so we are safe
in CLONE_THREAD case, because current->sighand == p->sighand.

Otherwise, p->sighand is unlocked, the new process is already
visible to the find_task_by_pid(), but have a copy of parent's
'struct pid' in ->pids[PIDTYPE_TGID].

This means that __group_complete_signal() may hang while doing

	do ... while (next_thread() != p)

We can solve this problem if we reverse these 2 attach_pid()s:

	attach_pid() does wmb()

	group_send_sig_info() calls spin_lock(), which
	provides a read barrier. // Yes ?

I don't think we can hit this race in practice, but still.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There is a window after copy_process() unlocks ->sighand.siglock
and before it adds the new thread to the thread list.

In that window __group_complete_signal(SIGKILL) will not see the
new thread yet, so this thread will start running while the whole
thread group was supposed to exit.

I beleive we have another good reason to place attach_pid(PID/TGID)
under ->sighand.siglock. We can do the same for

	release_task()->__unhash_process()

	de_thread()->switch_exec_pids()

After that we don't need tasklist_lock to iterate over the thread
list, and we can simplify things, see for example do_sigaction()
or sys_times().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Looks like somebody forgot to use the _bh spin_lock variant. We ran into a 
deadlock where br->hello_timer expired while br_stp_disable_br() walked 
br->port_list. 
Signed-off-by: NAdrian Drzewiecki <z@drze.net>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To find out if a packet needs to be handled by IPsec after SNAT, packets
are currently rerouted in POST_ROUTING and a new xfrm lookup is done. This
breaks SNAT of non-unicast packets to non-local addresses because the
packet is routed as incoming packet and no neighbour entry is bound to the
dst_entry. In general, it seems to be a bad idea to replace the dst_entry
after the packet was already sent to the output routine because its state
might not match what's expected.

This patch changes the xfrm lookup in POST_ROUTING to re-use the original
dst_entry without routing the packet again. This means no policy routing
can be used for transport mode transforms (which keep the original route)
when packets are SNATed to match the policy, but it looks like the best
we can do for now.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

98kbd{,-io} and 98spkr all went out with PC98 subarch.  Remove stale Makefile
entries that remained.
Signed-off-by: NArthur Othieno <apgo@patchbomb.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This updates the ads7846 touchscreen driver:
  - to allow faster clocking (this driver doesn't push sample rates);
  - bugfixes the conversion of spi_transfer to lists;
  - some dma-unsafe command buffers are fixed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>