Added SAPI value to use SAPIs different than 0.

Now fixed TEIs work in NT mode. This allows PTP endpoint to be connected
to PTMP ports together with other PTMP endpoints.

New enhanced version, thanks to Sam Ravnborg <sam@ravnborg.org> for the
hints.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Audio recording requires software audio processing.
Both hardware and software processing is simultaniously possible now.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DTMF digits were sent up to socket in locked state.
Receive audio stream was not enabled in certain condition.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IMHOLD_L1 ioctl.
The feature will be disabled on closing.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to protect the complete pipeline.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce stack size memory footprint of mISDN_dsp.
(From 1468 bytes for dsp_cmx_send on i386 down to 44).
Signed-off-by: NFrank Seidel <frank@f-seidel.de>
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added tx-fifo information for calculation of current delay to sync tx and rx
streams for echo canceler.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSP now uses ring buffer for echo canceler.
Added missing include in l1oip_codec.c
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch was made by Titus Moldovan and provides IOCTL functions for enabling
and disabling the controller's built in watchdog. The use is optional.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi:

skbuff: Copy csum instead of csum_start/csum_offset

It's easier to copy the u32 csum instead of its two u16
constituents.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Cheers,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi:

skbuff: Move new __skb_clone code into __copy_skb_header

It seems that people just keep on adding stuff to __skb_clone
instead __copy_skb_header.  This is wrong as it means your brand-new
attributes won't always get copied as you intended.

This patch moves them to the right place, and adds a comment to
prevent this from happening again.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for netdev->vlan_features in the myri10ge driver.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop the myri10ge_lro module parameter now that we have ethtool
to enable/disable LRO in the myri10ge driver.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the way we check whether lro_flush_all should be called
in the myri10ge driver.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of allocation failure, the actual ring size is rounded down to
nearest power of 2. The remaining descriptors are freed.
The CQ and SRQ are allocated with the actual size and the mask is updated.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when display channel info in debugfs, always check for valid band
before access the pointer and display information

for 1000 NIC, it only support "bgn" mode, so there is no 5.2GHz channels
available to display.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable using iwlwifi driver in AMT system.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rb value should be 0x10 for devices using ICT.
 RX interrupt was not performing well with
 0 value
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Periodic RX interrupt needed with ICT interrupt to prevent RX race.
Sending RX interrupt require many steps to be done in the
the device:
 1- write interrupt to current index in ICT table.
 2- dma RX frame.
 3- update RX shared data to indicate last write index.
 4- send interrupt.
This could lead to RX race, driver could receive RX interrupt
but the shared data changes does not reflect that.
this could lead to RX race, RX periodic will solve this race
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If RX queue becomes empty then we need to restock the queue from tasklet to prevent
ucode from starving. A caller to iwl_rx_allocate will decide if allocated buffer should
come from GFP_ATOMIC or GFP_KERNEL.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ICT interrupt handler support, ICT should improve CPU utilization
 since it does not require target read which is very expensive. This
 interrupt handler only added to 5000 cards and newer. Device will write
 interrupts to ICT shared table to inform driver about its interrupts.

These patches will not touch 3945 and 4965 interrupt handlers and tasklet.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the bug when using 11n "pure 40MHz" mode cause uCode
crashing by adding support for "pure 40MHz" in RX_ON command flag.
the "mode" field (bits 25:26) has value of 0-3
    0 = 20 MHz only
    1 = 40MHz only
    2 = Mixed
    3 = Reserved
Control Channel ID (bit 22) is valid only in Mixed mode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If transmit in HT rate, report the rate index as an MCS rate number
instead of an index. so "iw" can display correct BitRate
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new lock to be used when accessing some registers. Also move
    the register lock and iwl_grab_nic_access inside the function for register access. This
    will prevent from forgetting to hold locks and nic access in the right way and make code
    easier to maintain.

    We over use the priv->lock spin lock and I guess we need to add new
    one for Tx queue after that we might need to change most of these lock to
    BH and just keep priv->lock as irq type.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Two type of NVM available for devices 1000, 6000 and after, adding
support to read OTP lower blocks if OTP is used instead of EEPROM.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The USB ID with unknown manufacturer is apparently sweex,
copy it to the correct location of the list and add 2
additional USB ID's also belonging to Sweex.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

set_infra_mode() tried to restore wpa keys using add_wep_key(). This never
worked so prevent driver from trying.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split add_wpa_key() from rndis_iw_set_encode_ext so that conversion to cfg80211
would be easier later on.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver uses some unnamed bits to control encryption setup. Move these to
enumerations with proper names explaining their meaning.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BCM4320 doesn't support OID_802_11_TX_POWER_LEVEL (chip implements
the command but setting value has no effect and getting txpower value
always returns 0xff, full power). So remove the code for cleanup.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Old variant of bcm4320 doesn't handle setting configuration parameters
correctly. One symptom is that MAC gets partially overwritten when any
config parameters are set. This patch disables config-params for bcm4320a
(and generic rndis-wlan).
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The temperature measurement by uCode for 5150 and 5000 are different
        CSR_HW_REV_TYPE_5150: temperature sensor output voltage
        CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.

To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add "Greenfield" support for all devices except 4965 and
3945. "Greenfield" is part of 11n features to improve HT performance.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'tpt' is a delta throughput (number of packets) and is corelated
to brightness of the LED. We already maintain a delta of packets in
rxtxpackets. There is no need to calculate this delta again which
was affecting the behaviour of LEDS.

Also add two new callback functions for ASSOCIATED/DISASSOCIATED states
where LED's will be *on* for associated state and *off* for disassociated state.

This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1771.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.

SD8688 firmware introduces a new register for firmware status
which will never be overwritten.

Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver supports Intel's full MAC wireless multicomm 802.11 hardware.
Although the hardware is a 802.11agn device, we currently only support
802.11ag, in managed and ad-hoc mode (no AP mode for now).
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>