Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 23 4月, 2014 18 次提交
  3. 17 4月, 2014 19 次提交
    • J
      Merge branch 'master' of... · 4a0c3d9f
      由 John W. Linville 提交于 
      Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
      4a0c3d9f
    • K
      seccomp: fix memory leak on filter attach · 0acf07d2
      由 Kees Cook 提交于 
      This sets the correct error code when final filter memory is unavailable,
and frees the raw filter no matter what.

unreferenced object 0xffff8800d6ea4000 (size 512):
  comm "sshd", pid 278, jiffies 4294898315 (age 46.653s)
  hex dump (first 32 bytes):
    21 00 00 00 04 00 00 00 15 00 01 00 3e 00 00 c0  !...........>...
    06 00 00 00 00 00 00 00 21 00 00 00 00 00 00 00  ........!.......
  backtrace:
    [<ffffffff8151414e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff811a3a40>] __kmalloc+0x280/0x320
    [<ffffffff8110842e>] prctl_set_seccomp+0x11e/0x3b0
    [<ffffffff8107bb6b>] SyS_prctl+0x3bb/0x4a0
    [<ffffffff8152ef2d>] system_call_fastpath+0x1a/0x1f
    [<ffffffffffffffff>] 0xffffffffffffffff
Reported-by: NMasami Ichikawa <masami256@gmail.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Tested-by: NMasami Ichikawa <masami256@gmail.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0acf07d2
    • D
      isdn: icn: buffer overflow in icn_command() · b7a31405
      由 Dan Carpenter 提交于 
      This buffer over was detected using static analysis:

	drivers/isdn/icn/icn.c:1325 icn_command()
	error: format string overflow. buf_size: 60 length: 98

The calculation for the length of the string is off because it assumes
that the dial[] buffer holds a 50 character string, but actually it is
at most 31 characters and NUL.  I have removed the dial[] buffer because
it isn't needed.

The maximum length of the string is actually 79 characters and a NUL.  I
have made the cbuf[] array large enough to hold it and changed the
sprintf() to an snprintf() as a further safety enhancement.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b7a31405
    • N
      ip6_tunnel: use the right netns in ioctl handler · 74462f0d
      由 Nicolas Dichtel 提交于 
      Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      74462f0d
    • N
      sit: use the right netns in ioctl handler · 9aad77c3
      由 Nicolas Dichtel 提交于 
      Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).

Note that netdev_priv(dev) cannot bu NULL, hence we can remove these useless
checks.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9aad77c3
    • N
      ip_tunnel: use the right netns in ioctl handler · 8c923ce2
      由 Nicolas Dichtel 提交于 
      Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).

The variable 'tunnel' was used only to get 'itn', hence to simplify code I
remove it and use 't' instead.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8c923ce2
    • J
      net: use SYSCALL_DEFINEx for sys_recv · b7c0ddf5
      由 Jan Glauber 提交于 
      Make sys_recv a first class citizen by using the SYSCALL_DEFINEx
macro. Besides being cleaner this will also generate meta data
for the system call so tracing tools like ftrace or LTTng can
resolve this system call.
Signed-off-by: NJan Glauber <jan.glauber@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b7c0ddf5
    • D
      Merge branch 'mdio-gpio' · c3206e6f
      由 David S. Miller 提交于 
      Guenter Roeck says:

====================
net: mdio-gpio enhancements

The following series of patches adds support for active-low gpio pins
as well as for systems with separate MDI and MDO pins to the mdio-gpio
driver.

A board using those features is based on a COM Express CPU board.
The COM Express standard supports GPIO pins on its connector,
with one caveat: The pins on the connector have fixed direction
and are hard configured either as input or output pins.
The COM Express Design Guide [1] provides additional details.

The hardware uses three of the GPO/GPI pins from the COM Express board
to drive an MDIO bus. Connectivity between GPI/GPO pins and the MDIO bus
is as follows.

GPI2 --------------------+------------ MDIO
                         |
            +--------+   |
GPO2 ---+---G        |   |
        |   |        |   |
       4.7k | 2N7002 D---+
	|   |        |
	+---S        |
	|   +--------+
       GND

GPO1 --------------------------------- MDC

To support this hardware, two extensions to the driver were necessary.

- Due to the FET in the MDO path (GPO2), the MDO signal is inverted.
  The driver therefore has to support active-low GPIO pins.

- The MDIO signal must be separated into MDI and MDO.

Those changes are implemented in patch 2/3 and 3/3.
Patch 1/3 simplifies the error path and thus the subsequent
patches.

[1] http://www.picmg.org/pdf/picmg_comdg_100.pdf
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c3206e6f
    • G
      net: mdio-gpio: Add support for separate MDI and MDO gpio pins · f1d54c47
      由 Guenter Roeck 提交于 
      This is for a system with fixed assignments of input and output pins
(various variants of Kontron COMe).
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f1d54c47
    • G
      net: mdio-gpio: Add support for active low gpio pins · 1d251481
      由 Guenter Roeck 提交于 
      Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1d251481
    • G
      net: mdio-gpio: Use devm_ functions where possible · 78cdb079
      由 Guenter Roeck 提交于 
      This simplifies error path and deinit/removal functions.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      78cdb079
    • D
      Merge branch 'fib_validate_loopback' · bc383ea5
      由 David S. Miller 提交于 
      Cong Wang says:

====================
ipv4: fix flowi4_iif for input routing

This patchset fixes ->flowi4_iif for input routing and rp filter,
based on suggestion from Julian. See per patch for details.

v1 -> v2:
* merge the first two patches into one
* fix fib_check_nh() too
* add this cover letter
====================
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Reviewed-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bc383ea5
    • C
      ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source() · 0d5edc68
      由 Cong Wang 提交于 
      In my special case, when a packet is redirected from veth0 to lo,
its skb->dev->ifindex would be LOOPBACK_IFINDEX. Meanwhile we
pass the hard-coded LOOPBACK_IFINDEX to fib_validate_source()
in ip_route_input_slow(). This would cause the following check
in fib_validate_source() fail:

            (dev->ifindex != oif || !IN_DEV_TX_REDIRECTS(idev))

when rp_filter is disabeld on loopback. As suggested by Julian,
the caller should pass 0 here so that we will not end up by
calling __fib_validate_source().

Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0d5edc68
    • C
      ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif · 6a662719
      由 Cong Wang 提交于 
      As suggested by Julian:

	Simply, flowi4_iif must not contain 0, it does not
	look logical to ignore all ip rules with specified iif.

because in fib_rule_match() we do:

        if (rule->iifindex && (rule->iifindex != fl->flowi_iif))
                goto out;

flowi4_iif should be LOOPBACK_IFINDEX by default.

We need to move LOOPBACK_IFINDEX to include/net/flow.h:

1) It is mostly used by flowi_iif

2) Fix the following compile error if we use it in flow.h
by the patches latter:

In file included from include/linux/netfilter.h:277:0,
                 from include/net/netns/netfilter.h:5,
                 from include/net/net_namespace.h:21,
                 from include/linux/netdevice.h:43,
                 from include/linux/icmpv6.h:12,
                 from include/linux/ipv6.h:61,
                 from include/net/ipv6.h:16,
                 from include/linux/sunrpc/clnt.h:27,
                 from include/linux/nfs_fs.h:30,
                 from init/do_mounts.c:32:
include/net/flow.h: In function ‘flowi4_init_output’:
include/net/flow.h:84:32: error: ‘LOOPBACK_IFINDEX’ undeclared (first use in this function)

Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6a662719
    • C
      mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll · c98235cb
      由 Chris Mason 提交于 
      The mlx4 driver is triggering schedules while atomic inside
mlx4_en_netpoll:

	spin_lock_irqsave(&cq->lock, flags);
	napi_synchronize(&cq->napi);
		^^^^^ msleep here
	mlx4_en_process_rx_cq(dev, cq, 0);
	spin_unlock_irqrestore(&cq->lock, flags);

This was part of a patch by Alexander Guller from Mellanox in 2011,
but it still isn't upstream.
Signed-off-by: NChris Mason <clm@fb.com>
cc: stable@vger.kernel.org
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c98235cb
    • D
      Merge branch 'mvneta_qsgmii' · b07afe07
      由 David S. Miller 提交于 
      Thomas Petazzoni says:

====================
net: mvneta: fix usage as a module, and support QSGMII properly

This set of patches is a new attempt at fixing the operation of the
mvneta driver when built as a module. For the record, the previous
attempt, merged in commit e3a8786c
('net: mvneta: fix usage as a module on RGMII configurations') caused
problems for all RGMII configurations.

In fact, it turned out that the MAC to PHY connection on the Armada XP
GP, which was described as using RGMII-ID according to its Device
Tree, is in fact a QSGMII connection. And the RGMII and QSGMII
configurations have to be handled in a different way in the driver,
because the SERDES configuration is different in those two cases.

So, this patch series fixes that by:

 * Adding minimal handling of a "qsgmii" connection type in the PHY
   layer. Mainly to make sure that a "qsgmii" phy-mode in the Device
   Tree is recognized, and handed over to the driver as
   PHY_INTERFACE_QSGMII.

 * Changing the mvneta driver to properly configure the RGMIIEn and
   PCSEn bits in the GMAC_CTRL_2 register, and configure the SERDES
   register, in the three possible cases: RGMII, SGMII and QSGMII.

 * Updating the Device Tree of the Armada XP GP board to reflect the
   fact that it uses a QSGMII MAC/PHY connection.

PATCH 1 and 2 would be merged by David Miller, through the net tree,
while PATCH 3 would be merged by the mach-mvebu maintainers, through
their tree and arm-soc.

This set of patches has been tested on:

 * Armada XP GP (four QSGMII interfaces)
 * Armada XP DB (two RGMII interfaces and two SGMII interfaces)
 * Armada 370 Mirabox (two RGMII interfaces)

I've tested both the driver built-in, and compiled as a module.

Since the last attempt at fixing this was quite a fiasco, I'd like
this new attempt to be tested more widely before being applied. I'll
try to do some testing on other Armada boards I have, but independent
testing from other persons would also be appreciated.

Note that these patches apply after reverting the previous attempt,
obviously.
====================
Tested-by: NArnaud Ebalard <arno@natisbad.org>
Tested-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b07afe07
    • T
      net: mvneta: properly configure the MAC <-> PHY connection in all situations · 3f1dd4bc
      由 Thomas Petazzoni 提交于 
      Commit 5445eaf3 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.

However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.

In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.

Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:

 - QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
   the SERDES is configured in QSGMII. Technically speaking,
   configuring the SERDES of the first port would be sufficient, but
   it is simpler to do it on all ports.

 - SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
   the SERDES is configured as SGMII.

 - RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
   cleared, and no SERDES configuration is done, because RGMII is not
   using SERDES lanes.

 - other: an error is returned. For this reason, the
   mvneta_port_power_up() now returns an int instead of nothing, and
   the return value is checked by mvneta_probe().

This has been successfully tested on:

 * Armada XP DB, which has two RGMII and two SGMII connections
 * Armada XP GP, which uses QSGMII for its four interfaces
 * Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3f1dd4bc
    • T
      net: phy: add minimal support for QSGMII PHY · b9d12085
      由 Thomas Petazzoni 提交于 
      This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."

This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b9d12085
    • E
      sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast) · e283546c
      由 Edward Cree 提交于 
      When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.

Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.

For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.

efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
 mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.

The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others.  Thus, it uses separate logic.

Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e283546c
  5. 16 4月, 2014 3 次提交
    • L
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · 10ec34fc
      由 Linus Torvalds 提交于 
      Pull networking fixes from David Miller:

 1) Fix BPF filter validation of netlink attribute accesses, from
    Mathias Kruase.

 2) Netfilter conntrack generation seqcount not initialized properly,
    from Andrey Vagin.

 3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
    from Patrick McHardy.

 4) Properly limit MTU over ipv6, from Eric Dumazet.

 5) Fix seccomp system call argument population on 32-bit, from Daniel
    Borkmann.

 6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
    skb->mac_len needs to be used.  From Vlad Yasevich.

 7) We have several cases of using socket based communications to
    implement a tunnel.  For example, some tunnels are encapsulations
    over UDP so we use an internal kernel UDP socket to do the
    transmits.

    These tunnels should behave just like other software devices and
    pass the packets on down to the next layer.

    Most importantly we want the top-level socket (eg TCP) that created
    the traffic to be charged for the SKB memory.

    However, once you get into the IP output path, we have code that
    assumed that whatever was attached to skb->sk is an IP socket.

    To keep the top-level socket being charged for the SKB memory,
    whilst satisfying the needs of the IP output path, we now pass in an
    explicit 'sk' argument.

    From Eric Dumazet.

 8) ping_init_sock() leaks group info, from Xiaoming Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  cxgb4: use the correct max size for firmware flash
  qlcnic: Fix MSI-X initialization code
  ip6_gre: don't allow to remove the fb_tunnel_dev
  ipv4: add a sock pointer to dst->output() path.
  ipv4: add a sock pointer to ip_queue_xmit()
  driver/net: cosa driver uses udelay incorrectly
  at86rf230: fix __at86rf230_read_subreg function
  at86rf230: remove check if AVDD settled
  net: cadence: Add architecture dependencies
  net: Start with correct mac_len in skb_network_protocol
  Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
  cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
  net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
  seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
  qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
  qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
  qlcnic: Fix PVID configuration on eSwitch port.
  qlcnic: Fix max ring count calculation
  qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
  qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
  ...
      10ec34fc
    • S
      cxgb4: use the correct max size for firmware flash · 6f1d7210
      由 Steve Wise 提交于 
      The wrong max fw size was being used and causing false
"too big" errors running ethtool -f.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6f1d7210
    • A
      qlcnic: Fix MSI-X initialization code · 8564ae09
      由 Alexander Gordeev 提交于 
      Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.

Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Acked-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8564ae09