Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When removing a volume/device we need to switch the connection
status of the peer back into WFReportParams.

  Before this fix it was left in Connected state. That means that
  the peer device continued to inform us about state changes, etc...
  But we deleted that minor -> protocol error.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

* drbd-8.3:
  documentation: Documented detach's --force and disk's --disk-timeout
  drbd: Implemented the disk-timeout option
  drbd: Force flag for the detach operation
  drbd: Allow new IOs while the local disk in in FAILED state
  drbd: Bitmap IO functions can not return prematurely if the disk breaks
  drbd: Added a kref to bm_aio_ctx
  drbd: Hold a reference to ldev while doing meta-data IO
  drbd: Keep a reference to the bio until the completion handler finished
  drbd: Implemented wait_until_done_or_disk_failure()
  drbd: Replaced md_io_mutex by an atomic: md_io_in_use
  drbd: moved md_io into mdev
  drbd: Immediately allow completion of IOs, that wait for IO completions on a failed disk
  drbd: Keep a reference to barrier acked requests
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

drbdadm already has a --dry-run option, so this option cannot directly be
passed through to drbdsetup.  Rename the drbdsetup option to resolve this
conflict.

For backward compatibility, make --dry-run an alias of --tentative.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

This is what it is called in config files and on the command line as
well.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

 * Updates to all configuration items is done under genl_lock().
   Including removal of mdevs or tconns.
 * All read non sleeping read sides are protected by rcu
 * All sleeping read sides keep reference counts to keep the
   objects alive
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparing removal of drbd_cfg_rwsem
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Change the --no-tcp-cork drbdsetup command line option as well as
the no_cork netlink packet.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Change the --no-disk-drain drbdsetup command line option as well as
the no_disk_drain netlink packet.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Change the --no-disk-flushes drbdsetup command line option as well as
the no_disk_flush netlink packet.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

This removes the issue with using peer_seq_lock out of different
contexts.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

* Moved rs_planed into it, named total
* When having a pointer to the object the values can
  be embedded into the fifo object.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparing RCU for disk_conf
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparing RCU for disk_conf
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparing to use the same mutex for disk_conf updates
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If a forced disconnect hits a restarting receiver right after it passed
its final "if (C_DISCONNECTING)" test in drbdd_init(), but before it was
actually restarted by drbd_thread_setup, we could be left with a
connection stuck in C_DISCONNECTING, never reaching C_STANDALONE,
which would be necessary to take it down or reconfigure it.

Move the last cleanup into w_after_conn_state_ch(), and do an additional
state change request in conn_try_disconnect(), just in case.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The main purpose of this is to allow to turn data integrity checking on
and off on demand without causing interruptions.

Implemented by allocating tconn->peer_integrity_tfm only when receiving
a P_PROTOCOL message.  l accesses to tconn->peer_integrity_tf happen in
worker context, and no further synchronization is necessary.

On the sender side, tconn->integrity_tfm is modified under
tconn->data.mutex, and a P_PROTOCOL message is sent whenever.  All
accesses to tconn->integrity_tfm already happen under this mutex.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We allocate hash transformations with crypto_alloc_hash() which will
only return hash algorithms.  It is not necessary to reconfirm that we
actually got a hash algorithm.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

It is not enough to grab net_conf->integrity_alg under rcu_read_lock()
and access it outside of it; the entire net_conf object may be gone by
then.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If an admin requests disconnect at a time when the state handling
already disconnects/reconnects, there have been some races.

Make sure to always really stop the network threads before
returning success for disconnect. Do not pretend successfull
forced disconnect, if the state handling returned an error.

Return success from drbd_adm_down() only after all threads are finished.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Now since it is possible to change the two_primaries config
flag while the connection is up, make sure we treat a peer_req
in a consistent way if the config flag changes while the peer_req
is under IO.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Removing the get_net_conf()/put_net_conf() functions
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Removing the get_net_conf()/put_net_conf() calls
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The wire protocol is no longer a property that is negotiated
between the two peers. It is now expressed with two bits
(DP_SEND_WRITE_ACK and DP_SEND_RECEIVE_ACK) in each data
packet. Therefore the primary node is free to change the
wire protocol at any time without disconnect/reconnect.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With this commit the locking for all accesses to IDRs is complete:

 * Non sleeping read accesses are protected by RCU
 * sleeping read accesses are protocted by a read lock on drbd_cfg_rwsem
 * accesses that add anything are protected by a write lock
 * accesses that remove an object are protoected by a write lock
   and a call to synchronize_rcu() after it is removed from the IDR
   and before the object is actually free()ed.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>