Add back 82580 loopback tests to ethtool.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).

Peter Boström noticed and reported the bug.
Signed-off-by: NRoger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also changed a log message to indicate that memory was not allocated
instead of memory not available!
Signed-off-by: NMalahal Naineni <malahal@us.ibm.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In my patch c194992c ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.

If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]

This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.

This patch should be backported to 3.11-stable.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).

Wait until firmware ack is written before unlocking channel
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.

This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.

Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The old implementation was heavy on str* functions and sprintf calls.
This version is more manual, but faster.

Profiling just the printing of a 3 char CAN-id resulted in 60 instructions
for the manual method and over 2000 for the sprintf method. Bear in
mind the profiling was done against libc and not the kernel sprintf.

Together with this rewrite an issue with sending and receiving of RTR frames
has been fixed by Oliver for the cases that the DLC is not zero.
Signed-off-by: NAndre Naujoks <nautsch2@gmail.com>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The locking is needed, since the the internal buffer for the CAN frames is
changed during the wakeup call. This could cause buffer inconsistencies
under high loads, especially for the outgoing short CAN packet skbuffs.

The needed locks led to deadlocks before commit
"5ede5253 tty: Remove extra wakeup from pty
write() path", which removed the direct callback to the wakeup function from the
tty layer.

As slcan.c is based on slip.c the issue in the original code is fixed, too.
Signed-off-by: NAndre Naujoks <nautsch2@gmail.com>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NMarc Kleine-Budde  <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx and rx urbs are not deallocated if something goes wrong in peak_usb_start().
The patch fixes error handling to deallocate all the resources.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG.  A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.

To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This bug was introduced by commit
7a163bfb ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch 136d8f37 broke the skge driver.
Note this part of the patch:
+               if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+                       dev_kfree_skb(nskb);
+                       goto resubmit;
+               }
+
                pci_unmap_single(skge->hw->pdev,
                                 dma_unmap_addr(e, mapaddr),
                                 dma_unmap_len(e, maplen),
                                 PCI_DMA_FROMDEVICE);
                skb = e->skb;
                prefetch(skb->data);
-               skge_rx_setup(skge, e, nskb, skge->rx_buf_size);

The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.

This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: NVasiliy Glazov <vascom2@gmail.com>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.

For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: NAnsis Atteka <aatteka@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.

With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 104a43ed
    cnic: Use CHIP_NUM macros from bnx2x.h

changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not.  There is another place in cnic that is still using
the old method to determine if FCoE is supported or not.  The 2 methods
may not yield the same result after the network interface is brought down
and up.  This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.

The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro.  As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit b9871bcf
    bnx2x: VF RSS support - PF side

changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc.  For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit afbd8bae
   vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
  ip link add vxlan1 type vxlan id 100
creates the following fdb entry
  00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent

This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: NAvinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.

Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.

Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree

Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215

[ Thadeu notes that: "... this issue might happen with the generation of
  initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
  which links to the port device at
  /sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NOlaf Hering <ohering@suse.com>
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver registration fails, we need to clean up the resources allocated
before. cxgb4 missed to destroy the workqueue allocated at the very beginning.

This patch destroies the workqueue when registration fails.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic.  However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data.  Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NAcked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes sparse warnings when incorrectly handling the port number
and using int instead of unsigned int iterating through &vn->sock_list[].
Keeping the port as __be16 also makes things clearer wrt endianess.
Also, it was pointed out that vxlan_get_rx_port() had unnecessary checks
which got removed.
Signed-off-by: NJoseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o At the time of firmware hang "adapter->need_fw_reset" variable gets
  set but after re-initialization of firmware OR at the time of VF
  re-initialization that variable was not getting cleared which
  was leading to failure in VF reset recovery.Fix it by clearing
  this variable before re-initializing VF
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>