Rename mei_cl_irq_close to mei_cl_irq_disconnect
and MEI_FOP_CLOSE to MEI_FOP_DISCONNECT
Remove unused MEI_FOP_OPEN
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

HBM uses global list of status values
from which the values of particular commands
are derived
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When handling dynamic clients there might be a race
scenario in which two me clients with the same me
address would be linked in the me clients list,
therefore we need to search by both uuid and me address.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To support dynamic addition/remove we add wrappers
for removal of me clients
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To support dynamic addition/remove of clients
it is more convenient to use list instead of
static array
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For support of dynamic addition and removal of me clients
it is more convenient to use a list instead of static array
as is use now.
As the first step of the transition to the new data structure
we change the lookup function so it returns me client address
instead of an index.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reduce few code lines by using wrappers for sending
simple hbm client messages
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use consistently me_addr name in hbm protocol structures
to represent in firmware client address
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Amthif has its own queues therefore it is redundant
to check the client type when processing the queues
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace open coded loop with an existing service function:
mei_io_list_flush
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We cannot handle user interrupt in context of hw initialization
so we only wait for time out which is reasonably short
Also we don't need to check error from wait, only flag value.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

NFC will leak buffer if send failed.
Use single exit point that does the freeing

Cc: stable@vger.kernel.org #3.10+
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If connect request is queued (e.g. device in pg) set client state
to initializing, thus avoid preliminary exit in wait if current
state is disconnected.

This is regression from:

commit e4d8270e
Author: Alexander Usyskin <alexander.usyskin@intel.com>
mei: set connecting state just upon connection request is sent to the fw

CC: stable@vger.kernel.org # 3.15+
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We introduced unified FW status function in patch
mei: add per device configuration (lkml.org/lkml/2014/5/12/607)

This change made hw_ops functions unused and obsolete
therefore we remove these functions from source code.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

wait_event_timeout can return 0 or the remaining jiffies
so return -ETIME if disconnected state not reached.

Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Calling pm_schedule_suspend from the runtime pm idle callback
may reschedule existing timer, thus in case of frequent runtime
rpm idle call the suspend maybe starved.
Instead we call pm_runtime_autosuspend which is checking if the
timer is already charged.

An example is monitoring device pci config space.
Pci config sysfs handlers calls pci_config_pm_runtime_put/get
helpers which in turns calls to device idle callback

Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Link must be reset in case the fw doesn't
respond to client disconnect request.
We did charge the timer only in irq path
from mei_cl_irq_close and not in mei_cl_disconnect

Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On connection timeout we leave the connecting client in
connecting state. Since a new connection is stalled till
previous connection is completed in this case no new connection
is possible till the user space does release the file handle.
Therefore on timeout we move the client to disconnected state.

Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add WPT second mei interface.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to support more then one mei interface
hence the simple misc devices is not longer an option

In order not break the user space a device with pci function 0
need to be linked to /dev/mei
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move quirk FW type detector to cfg structure
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add mei_cfg structure that holds per device configuration
data and hooks, as the first step we add firmware
status register offsets
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According the spec the host should read H_CSR again
after asserting reset H_RST to ensure that reset was
read by the firmware

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It my take time till ME_RDY will be cleared after the reset,
so we cannot check the bit before we got the interrupt

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We cleared H_RST for H_CSR on spurious interrupt generated when ME_RDY
while cleared and not while  ME_RDY is set. The spurious interrupt
is not delivered on all platforms in this case the
driver may fail to initialize.

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

we never freed the mei_clients array on driver shutdown
only on reset
add mei_hbm_reset function that wraps the hbm cleanup
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding power gating introduced new waiting state for client also during
connection attempt, a connection request can be queued for later either due
device is power gated or due to other on going connection.
We setting client connection state before start of full connect procedure so
in both cased the client state will be MEI_FILE_CONNECTING
which create interlock between the two connection attempts, both
detecting that another connection is in progress.

The interlock is resolved by moving client to connecting state
only upon connection request transmission, so the  first
cb in queue can be processed.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Follow-up for bits missed in
commit 7ca96aa2
mei: make return values consistent across the driver
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fetch FW status registers, as they are important in
in understanding of FW reset reasons
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Communicate hbm version 1.1 to firmware to tell that we
now support power gating isolation protocol
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For non wakeable devices we can't use pci runtime framework
as we are not able to wakeup from D3 states.
Instead we create new pg runtime domain that only drives TXE power
gating protocol to reduce the power consumption.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For non wakeable devices we can't use pci runtime framework
as we are not able to wakeup from D3 states.
Instead we create new pg runtime domain that only drives ME power
gating protocol to reduce the power consumption.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Take rpm token on operation start to initiate rpm resume if needed.
Mark last busy time, release token and advice rpm framework
to try to autosuspend on operation end.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm framework for TXE devices.
The runtime pm handlers are used to run
txe power gating isolation protocol.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm framework for ME devices.
The runtime pm handlers are used to run
me power gating isolation protocol
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver needs to check whether the write
queue idle before entering power gating
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For power gating entry we write hbm pg entry request command and
then we set pg register
For power gating exit we clear pg register and wait for exit request
hbm command.

Exit power gating request might also be initiated by the firmware
w/o explicit driver request

The power gating state is tracked by pg_state member of me_hw
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the runtime pm and the internal power gating
cannot be in complete sync in regards to I/O
operations, we need to expose the device
hardware internal power gating state to mei layer

2. We add pg_state handler that translate the hw
internal pg state to mei layer

2. We add power gating event variable to keep
power track of power gating transitions
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable power gating isolation only if hw and fw support it.
This is indicated by ME_PGIC_HRA bit in ME_CSR_HA register
and on HBM protocol version.

The information is exported to MEI layer through
new pg_is_enabled hw op.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add entry and exit power gating isolation register
write handler.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>