Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.

Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

apb_calc_first_last(), apb_fake_ranges(), pci_of_scan_bus(),
of_scan_pci_bridge(), pci_of_scan_bus(), and pci_scan_one_pbm()
should all be __devinit.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some minor refactoring in the generic code was necessary for
this:

1) This controller requires 8-byte access to the interrupt map
   and clear register.  They are 64-bits on all the other
   SBUS and PCI controllers anyways, so this was easy to cure.

2) The IMAP register has a different layout and some bits that we
   need to preserve, so use a read/modify/write when making
   changes to the IMAP register in generic code.

3) Flushing the entire IOMMU TLB is best done with a single write
   to a register on this PCI controller, add a iommu->iommu_flushinv
   for this.

Still lacks MSI support, that will come later.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set_irq_msi() currently connects an irq_desc to an msi_desc. The archs call
it at some point in their setup routine, and then the generic code sets up the
reverse mapping from the msi_desc back to the irq.

set_irq_msi() should do both connections, making it the one and only call
required to connect an irq with it's MSI desc and vice versa.

The arch code MUST call set_irq_msi(), and it must do so only once it's sure
it's not going to fail the irq allocation.

Given that there's no need for the arch to return the irq anymore, the return
value from the arch setup routine just becomes 0 for success and anything else
for failure.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This helps deal with the invisible bridge that sits between
the host controller and the top-most visisble PCI devices
on hypervisor systems.

For example, on T1000 the bus-range property says 2 --> 4
and so there is a PCI express bridge at bus 2, devfn 0, etc.

So if we don't force the dummy host controller to bus zero,
we'll try to create two devices with the same domain/bus/devfn
triplet.

Also, add some more log diagnostics to make debugging stuff like this
easyer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We fake up a dummy one in all cases because that is the simplest
thing to do and it happens to be necessary for hypervisor systems.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a similar patch for x86_64 written by
Stephen Hemminger.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't do the "Simba APB is a PBM" bogosity for Sabre
controllers any longer, so this pbms_same_domain thing
is no longer necessary.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the implementations can be identical and generic, so
no need for controller specific methods.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SIMBA APB bridge is strange, it is a PCI bridge but it lacks
some standard OF properties, in particular it lacks a 'ranges'
property.

What you have to do is read the IO and MEM range registers in
the APB bridge to determine the ranges handled by each bridge.
So fill in the bus resources by doing that.

Since we now handle this quirk in the generic PCI and OF device
probing layers, we can flat out eliminate all of that code from
the sabre pci controller driver.

In fact we can thus eliminate completely another quirk of the sabre
driver.  It tried to make the two APB bridges look like PBMs but that
makes zero sense now (and it's questionable whether it ever made sense).
So now just use pbm_A and probe the whole PCI hierarchy using that as
the root.

This simplification allows many future cleanups to occur.

Also, I've found yet another quirk that needs to be worked around
while testing this.  You can't use the 'class-code' OF firmware
property, especially for IDE controllers.  We have to read the value
out of PCI config space or else we'll see the value the device was
showing before it was programmed into native mode.

I'm starting to think it might be wise to just read all of the values
out of PCI config space instead of using the OF properties. :-/
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to traverse recursively down child busses else we only
get the file created under devices at the top-level.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only user was bus_dvma_to_mem() which is no longer used
by any driver, so kill that, and the export of pci_memspace_mask.

The only user now is the PCI mmap support code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Almost entirely taken from the 64-bit PowerPC PCI code.

This allowed to eliminate a ton of cruft from the sparc64
PCI layer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix section mismatch in arch/sparc/kernel/pcic.c and 
arch/sparc64/kernel/pci.c.
Signed-off-by: NRobert Reif <reif@earthlink.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to use get_irq_msi() not get_irq_data().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is kind of hokey, we could use the hardware provided facilities
much better.

MSIs are assosciated with MSI Queues.  MSI Queues generate interrupts
when any MSI assosciated with it is signalled.  This suggests a
two-tiered IRQ dispatch scheme:

	MSI Queue interrupt --> queue interrupt handler
		MSI dispatch --> driver interrupt handler

But we just get one-level under Linux currently.  What I'd like to do
is possibly stick the IRQ actions into a per-MSI-Queue data structure,
and dispatch them form there, but the generic IRQ layer doesn't
provide a way to do that right now.

So, the current kludge is to "ACK" the interrupt by processing the
MSI Queue data structures and ACK'ing them, then we run the actual
handler like normal.

We are wasting a lot of useful information, for example the MSI data
and address are provided with ever MSI, as well as a system tick if
available.  If we could pass this into the IRQ handler it could help
with certain things, in particular for PCI-Express error messages.

The MSI entries on sparc64 also tell you exactly which bus/device/fn
sent the MSI, which would be great for error handling when no
registered IRQ handler can service the interrupt.

We override the disable/enable IRQ chip methods in sun4v_msi, so we
have to call {mask,unmask}_msi_irq() directly from there.  This is
another ugly wart.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The setting of the CACHE_LINE_SIZE register in sparc64's pci
initialisation code isn't quite adequate as the device may have
incompatible requirements.  The generic code tests for this, so switch
sparc64 over to using it.

Since sparc64 has different L1 cache line size and PCI cache line size,
it would need to override the generic code like i386 and ia64 do.  We
know what the cache line size is at compile time though, so introduce a
new optional constant PCI_CACHE_LINE_BYTES.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NDavid Miller <davem@davemloft.net>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Do IRQ determination generically by parsing the PROM properties,
and using IRQ controller drivers for final resolution.

One immediate positive effect is that all of the IRQ frobbing
in the EBUS, ISA, and PCI controller layers has been eliminated.
We just look up the of_device and use the properly computed
value.

The PCI controller irq_build() routines are gone and no longer
used.  Unfortunately sbus_build_irq() has to remain as there is
a direct reference to this in the sunzilog driver.  That can be
killed off once the sparc32 side of this is written and the
sunzilog driver is transformed into an "of" bus driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow them to be enabled with "pci=irq_verbose" on the
boot command line.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It can be pushed even further down, but this is a first step.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the long overdue conversion of sparc64 over to
the generic IRQ layer.

The kernel image is slightly larger, but the BSS is ~60K
smaller due to the reduced size of struct ino_bucket.

A lot of IRQ implementation details, including ino_bucket,
were moved out of asm-sparc64/irq.h and are now private to
arch/sparc64/kernel/irq.c, and most of the code in irq.c
totally disappeared.

One thing that's different at the moment is IRQ distribution,
we do it at enable_irq() time.  If the cpu mask is ALL then
we round-robin using a global rotating cpu counter, else
we pick the first cpu in the mask to support single cpu
targetting.  This is similar to what powerpc's XICS IRQ
support code does.

This works fine on my UP SB1000, and the SMP build goes
fine and runs on that machine, but lots of testing on
different setups is needed.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SYM2 driver uses it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the callers do a pgprot_noncached() on
vma->vm_page_prot.

Pointed out by Hugh Dickens.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Abstract out IOMMU operations so that we can have a different
set of calls on sun4v, which needs to do things through
hypervisor calls.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were three changes necessary in order to allow
sparc64 to use setup-res.c:

1) Sparc64 roots the PCI I/O and MEM address space using
   parent resources contained in the PCI controller structure.
   I'm actually surprised no other platforms do this, especially
   ones like Alpha and PPC{,64}.  These resources get linked into the
   iomem/ioport tree when PCI controllers are probed.

   So the hierarchy looks like this:

   iomem --|
	   PCI controller 1 MEM space --|
				        device 1
					device 2
					etc.
	   PCI controller 2 MEM space --|
				        ...
   ioport --|
            PCI controller 1 IO space --|
					...
            PCI controller 2 IO space --|
					...

   You get the idea.  The drivers/pci/setup-res.c code allocates
   using plain iomem_space and ioport_space as the root, so that
   wouldn't work with the above setup.

   So I added a pcibios_select_root() that is used to handle this.
   It uses the PCI controller struct's io_space and mem_space on
   sparc64, and io{port,mem}_resource on every other platform to
   keep current behavior.

2) quirk_io_region() is buggy.  It takes in raw BUS view addresses
   and tries to use them as a PCI resource.

   pci_claim_resource() expects the resource to be fully formed when
   it gets called.  The sparc64 implementation would do the translation
   but that's absolutely wrong, because if the same resource gets
   released then re-claimed we'll adjust things twice.

   So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource()
   conversion before passing it on to pci_claim_resource().

3) I was mistakedly __init'ing the function methods the PCI controller
   drivers provide on sparc64 to implement some parts of these
   routines.  This was, of course, easy to fix.

So we end up with the following, and that nasty SPARC64 makefile
ifdef in drivers/pci/Makefile is finally zapped.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0.  This leaves such
a device in an inaccessible state.  The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.

The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.

Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot.  Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.

Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification.  This is
especially true since often many devices are covered by the same
driver.  It likely would be necessary to replicate code across dozens
of drivers.

The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register.  I believe it is safe to include
this patch as part of the PCI infrastructure.

The cleanest implementation of pci_restore_bars was to call
pci_update_resource.  Unfortunately, that does not currently exist
for the sparc64 architecture.  The patch below includes a null
implemenation of pci_update_resource for sparc64.

Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's been deprecated long enough and there are no in-tree
users any longer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pcibios_bus_to_resource is exported on all architectures except ia64
and sparc.  Add exports for the two missing architectures.  Needed when
Yenta socket support is compiled as a module.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Revert commit fec59a71, which is
breaking sparc64 that doesn't have a working pci_update_resource.

We'll re-do this after 2.6.13 when we'll do it all properly.

Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0.  This leaves such
a device in an inaccessible state.  The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.

The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.

Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot.  Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.

Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification.  This is
especially true since often many devices are covered by the same
driver.  It likely would be necessary to replicate code across dozens
of drivers.

The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register.  I believe it is safe to include
this patch as part of the PCI infrastructure.

The cleanest implementation of pci_restore_bars was to call
pci_update_resource.  Unfortunately, that does not currently exist
for the sparc64 architecture.  The patch below includes a null
implemenation of pci_update_resource for sparc64.

Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!