As I just discovered while doing WoWLAN, HW crypto
is done wrong for GTKs: they should be programmed
for the AP station ID (in the managed mode case)
and the HW can actually deal with multiple group
keys per station as well (which is useful in IBSS
RSN but that I've chosen not to use this).

To fix all this, modify the way keys are sent to
the device and key offsets are allocated. After
these changes, key offsets are stored into the
hw_key_idx which we can then track for the key
lifetime, not relying on our sta_cmd array. WEP
default keys get special treatment, of course.

Additionally, since I had the API for it, we can
now pre-fill TKIP phase 1 keys for RX now that we
can obtain the P1K from mac80211, a capability I
had added for WoWLAN initially.

Finally, some keys simply don't need to be added
into the device's key cache -- a key that won't
be used for RX is only needed in the TX header,
so "pretend" to have accepted any key without
adding it into the device -- no need to use up
key space there for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, extra _agn in priv structure is no needed, remove it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The price to pay is the access to the log system. Therefore logs from bus layer
are sent by dev_printk instead of IWL_XXXX.

Rename bus->priv to bus->drv_data to make the separation even clearer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Call iwl_probe with a ready iwl_bus struct. This means that the bus layer
assigns the irq, dev and iwl_bus_ops pointers to iwl_bus before giving it to
iwl_probe.

The device specific struct is allocated together with the common iwl_bus struct
by the bus specific layer. The pointer to the aggregate struct is passed to the
upper layer that holds a pointer to iwl_bus instead of an embedded iw_bus.
The private data given to the PCI subsystem is now iwl_bus and not iwl_priv.

Provide bus_* inliners on the way in order  to simplify the syntax.

Rename iwl-pci.h -> iwl-bus.h since it is bus agnostic and represent the
external of the bus layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

It still holds a pointer to iwl_priv. But hopefully this will disappear at some point.
Also add the multiple inclusion protection to iwl-trans.h that was forgotten.
Move iwl-trans structures to iwl-trans.h
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This function is really related to the transport layer - move it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Basically all the nic_init flow should be in the transport layer.
iwl_prepare_card_hw will move to the transport too in a separate patch.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

All the configurations of the HW for AMPDU are now in the transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since iwlagn_setup_deferred_work is always called, fold it into
iwl_setup_deferred_work. BT related works are setup by the new
bt_setup_deferred_work lib_ops.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.guy@intel.com>

Since the ICT is transport related, move all its functions to the transport
layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since iwlagn_stop_device was the only caller to the rx_stop / tx_stop,
these two don't need to be API any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.guy@intel.com>

Also create a new file: iwl-trans-int-pcie.h which will include
the non static functions that are shared among the current pcie transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Not needed since the driver split.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

After driver split, no need to make the code so complex
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Most of the functions in iwl-agn-hcmd are move to other files, no point to
keep the file anymore.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The upper layer receives a pointer to an iwl_rx_mem_buffer. I would prefer the
upper layer to receive a pointer to an iwl_rx_packet, but this is impossible
since the Rx path needs to add the address of the page to the skb.
I may find a solution later.

All the pre_rx_handler and notification code has been moved to the upper layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since all the irq / tasklet is now handled in the transport layer, it should
give an API to ensure that all the irq / tasklet have finished running. This
will allow the upper layer to release all its resources.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

PCIe doesn't provide any ISR registration API, whereas other buses do.
Hence, we need to move the tasklet and irq to the transport layer to allow this
flexibility.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Multiple quoted strings are concatenated without comma separators.

Make the array const while there.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Declare iwl_mac_rssi_callback as "static"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WiFi throughput drops drastically when BT is turned on, BT and WiFi
are simultaneously transmitting/receiving traffic. This is particularly true
when BT has higher priority over WiFi, and hence the device defers TX frames.
The AP assumes that the channel is bad and reduces the data rate, implying
longer airtime, which exacerbates the problem further, resulting ultimately
in what is popularly called the "death-spiral" phenomenon. The use of PS-poll
in such scenarios guarantees a low but consistent throughput.

Since the death-spiral phenomenon is observed only when the RSSI is low, use
PS-poll only when RSSI is low and disable when high, with a known hysterisis.

This feature specifies the high and low thresholds and implements the
callbacks registered with mac80211, which will be called when threshold events
occur.

iwlwifi: dynamic pspoll: optimize rssi monitor code
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the for priv->trans.ops->...
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now, there are only two functions to send a host command:
* send_cmd that receives a iwl_host_cmd
* send_cmd_pdu that builds the iwl_host_cmd itself and received flags

The flags CMD_ASYNC / CMD_SYNC / CMD_WANT_SKB are not changed by the API
functions.

Kill the unused flags CMD_SIZE_NORMAL / CMD_NO_SKB on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx free functions move to the transport layer. Unify the functions that deal with tx queues and cmd queue.

Since the CMD queue is not fully allocated, but uses the q->n_bd / q->window trick, the release flow of TX queue and CMD queue was different.
iwlagn_txq_free_tfd receives now the index of the TFD to be freed, which allows to unify the release flow for all the queues.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All "agn" devices use the same hcmd functions, no need to call indirectly.
remove hcmd_ops
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Call the 2-wire and advanced bt-coex function directly to avoid mistake
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The transport layer ness to release all rx ressources. This function is an API for it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The transport layer is responsible for all the queues, DMA rings etc...
This is the beginning of the separation of all the code that is tighly
related to HW design to the aforementioned transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add the parameter to disable stuck queue watchdog timer, different platforms
might have different timing. Provide the option to disable the timer to prevent
un-necessary firmware reload.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Use the rate that mac80211 requested to fill the
uCode TX command for the beacon. Unfortunately,
the uCode is (currently?) ignoring it, but now
at least fill it properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add power_level module parameter to set the default power save level.
Power save level has range from 1 - 5, default power save level is 1.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add power_save module parameter to enable power management if needed
Default power management is disabled.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since the irq number is just an unsigned int, store it inside iwl_bus
instead of calling the get_irq ops every time it is needed.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

All pci related stuff is in iwl-pci.c.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

In order to remove a few more dereference to priv->pdev that will be killed
[Asoon, there is now a method to get the IRQ number.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The PCI_REVISION_ID is read and printed in iwl_pci_probe anyway using pr_info
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Get a pointer to the struct device during probe and get the rid of all the PCI
specific DMA wrappers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since we have now a PCI layer, all the init and deinit code that is PCI
related should move to there.

Also move the IO functions: read8/read32/write32. They need hw_base which
is killed from priv.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>