This is a regression fix after migration to the external GIC.
The breakage has been introduced in commit 69644a8e
("ARM: EXYNOS4: modify interrupt mappings for external GIC")
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: added commit id]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Remove duplicated #include('s) in
  arch/arm/mach-exynos4/cpu.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Use the correct regulator names for cpufreq
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

WARNING: vmlinux.o(.text+0xf47c): Section mismatch in reference from the function samsung_bl_set() to the (unknown reference) .init.data:(unknown)
The function samsung_bl_set() references
the (unknown reference) __initdata (unknown).
This is often because samsung_bl_set lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to commit 659fb32d
("replace irq_gc_ack() with {set,clr}_bit variants"), this
should be fixed.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Reported-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of setting up a match interrupt for 'current_time + delta'
on ->set_next_event(), program timer 0 to count down from 'delta - 1'
and trigger an interrupt when it reaches zero.
Signed-off-by: NLennert Buytenhek <buytenh@laptop.org>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NLennert Buytenhek <buytenh@laptop.org>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Currently, arch-mmp/time.c uses timer 0 both as a clocksource timer
and as a clockevent timer, the latter by setting up a comparator
interrupt to match on 'current_time + delta'.  This is problematic
if delta is small enough, as that can lead to 'current_time + delta'
already being in the past when comparator setup has finished, leading
to the requested event not triggering.

As there is also a silicon issue that requires stopping a timer's
counter while writing to one of its match registers, we'll switch to
using two separate timers -- timer 0 as clockevent timer, which we'll
start and stop on every invocation of ->set_next_event(), and timer 1
as clocksource timer, which will be free-running.

This first patch enables timer 1 on boot, so that we can use it as
clocksource timer.
Signed-off-by: NLennert Buytenhek <buytenh@laptop.org>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NTanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Move definitions from mfp-gplugd.h to mfp-pxa168.h as they aren't
gplugD specific.
Signed-off-by: NTanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This got added in:

	commit ef6c8445
	Author: Haojian Zhuang <haojian.zhuang@marvell.com>
	Date:   Wed Nov 24 11:54:25 2010 +0800

	    ARM: pxa: add iwmmx support for PJ4

which does:

-       mrc     p15, 0, r2, c15, c1, 0
-       orr     r2, r2, #0x3                    @ enable access to CP0 and CP1
-       mcr     p15, 0, r2, c15, c1, 0
+       @ enable access to CP0 and CP1
+       XSC(mrc p15, 0, r2, c15, c1, 0)
+       XSC(orr r2, r2, #0x3)
+       XSC(mcr p15, 0, r2, c15, c1, 0)

but then later does:

-       mrc     p15, 0, r4, c15, c1, 0
-       orr     r4, r4, #0x3                    @ enable access to CP0 and CP1
-       mcr     p15, 0, r4, c15, c1, 0
+       @ enable access to CP0 and CP1
+       XSC(mrc p15, 0, r4, c15, c1, 0)
+       XSC(orr r4, r4, #0xf)
+       XSC(mcr p15, 0, r4, c15, c1, 0)
Signed-off-by: NLennert Buytenhek <buytenh@laptop.org>
Acked-by Haojian <haojian.zhuang@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

There are three choices:

vsyscall=native: Vsyscalls are native code that issues the
corresponding syscalls.

vsyscall=emulate (default): Vsyscalls are emulated by instruction
fault traps, tested in the bad_area path.  The actual contents of
the vsyscall page is the same as the vsyscall=native case except
that it's marked NX.  This way programs that make assumptions about
what the code in the page does will not be confused when they read
that code.

vsyscall=none: Trying to execute a vsyscall will segfault.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/8449fb3abf89851fd6b2260972666a6f82542284.1312988155.git.luto@mit.eduSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

getcpu is available as a vdso entry and an emulated vsyscall.
Programs that for some reason don't want to use the vdso should
still be able to call getcpu without relying on the slow emulated
vsyscall.  It costs almost nothing to expose it as a real syscall.

We also need this for the following patch in vsyscall=native mode.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/6b19f55bdb06a0c32c2fa6dba9b6f222e1fde999.1312988155.git.luto@mit.eduSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

As of commit 98d0ac38
Author: Andy Lutomirski <luto@mit.edu>
Date:   Thu Jul 14 06:47:22 2011 -0400

    x86-64: Move vread_tsc and vread_hpet into the vDSO

user code no longer directly calls into code in arch/x86/kernel/, so
we don't need compile flag hacks to make it safe.  All vdso code is
in the vdso directory now.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/835cd05a4c7740544d09723d6ba48f4406f9826c.1312988155.git.luto@mit.eduSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

The PCI nanoengine driver in the SA1100 machine probably has not
been building for some time. It probably dragged hardware.h
in implicitly and now it doesn't anymore. After this an SA1100
build selecting all system variants will build successfully.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.

This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since 7203f8a4 (arm: mach-omap2: remove
NULL board_mux from board files) NULL board_mux is defined in mux.h.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use kstrdup rather than duplicating its implementation

The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The pointer "va" returned from "phys_to_virt(pa)" is never used in
"sgtable_fill_kmalloc()".So,it is safe to remove this set-but-unused variable.
Signed-off-by: NMaxin B. John <maxin.john@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Machine database already updated:
http://www.arm.linux.org.uk/developer/machines/list.php?id=3284Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing definitions for the AM3505/3517 UART4 such
as DMAs, INTs and base address.
Signed-of-by: NRaphael Assenat <raph@8d.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This has now been well tested, and several platforms are now selecting
this directly.  It's time to drop its experimental status.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Builds for multi-OMAP2 (e.g., OMAP2420 with OMAP2430) with
CONFIG_ARCH_OMAP4=n fail with the following errors:

arch/arm/mach-omap2/built-in.o: In function `_enable_module':
arch/arm/mach-omap2/omap_hwmod.c:701: undefined reference to `omap4_cminst_module_enable'
arch/arm/mach-omap2/built-in.o: In function `_disable_module':
arch/arm/mach-omap2/omap_hwmod.c:726: undefined reference to `omap4_cminst_module_disable'
arch/arm/mach-omap2/built-in.o: In function `_wait_target_disable':
arch/arm/mach-omap2/omap_hwmod.c:1179: undefined reference to `omap4_cminst_wait_module_idle'

This is probably due to the preprocessor directives in
arch/arm/plat-omap/include/plat/cpu.h that convert some cpu_is_omap*()
expressions from preprocessor directives into something that is only
resolvable during runtime, if multiple OMAP2 build targets are
selected.

Thanks to Tony Lindgren <tony@atomide.com> for reporting.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit b22f954b (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.

Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:

arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'

Fix the problem by moving the code to ifdef sections for omap3 and omap4.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support to Romely-EP SandyBridge.
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Signed-off-by: NAnhua Xu <anhua.xu@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1312264895-2010-1-git-send-email-youquan.song@intel.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

With the UM_SIGNAL alignment fault mode, no siginfo structure is
passed to userspace.

POSIX specifies how siginfo_t should be populated for alignment
faults, so this patch does just that:

  * si_signo = SIGBUS
  * si_code = BUS_ADRALN
  * si_addr = misaligned data address at which access was attempted
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NKirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Currently, it's possible to set the kernel to ignore alignment
faults when changing the alignment fault handling mode at runtime
via /proc/sys/alignment, even though this is undesirable on ARMv6
and above, where it can result in infinite spins where an un-fixed-
up instruction repeatedly faults.

In addition, the kernel clobbers any alignment mode specified on
the command-line if running on ARMv6 or above.

This patch factors out the necessary safety check into a couple of
new helper functions, and checks and modifies the fault handling
mode as appropriate on boot and on writes to /proc/cpu/alignment.

Prior to ARMv6, the behaviour is unchanged.

For ARMv6 and above, the behaviour changes as follows:

  * Attempting to ignore faults on ARMv6 results in the mode being
    forced to UM_FIXUP instead.  A warning is printed if this
    happened as a result of a write to /proc/cpu/alignment.  The
    user's UM_WARN bit (if present) is still honoured.

  * An alignment= argument from the kernel command-line is now
    honoured, except that the kernel will modify the specified mode
    as described above.  This is allows modes such as UM_SIGNAL and
    UM_WARN to be active immediately from boot, which is useful for
    debugging purposes.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

poison_init_mem() used a loop of:

	while ((count = count - 4))

which has 2 problems - an off by one error so that we do one less word
than we should, and the other is that if count == 0 then we loop forever
and poison too much.  On a platform with HAVE_TCM=y but nothing in the
TCM's, this caused corruption and the platform failed to boot.
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The file mm/proc-arm946.S contains a typo and is missing a structure
member in __arm946_proc_info.  The former prevents compilation
and the latter causes problems during boot.  It is likely this
file was manually copied from a similar file and not tested, then
later updates to the *_proc_info structures missed this file.

This patch will apply (with offset) with or without the
recent macro unification work that has been done in this directory.
This was verified against linux-next/stable last week.

See arm-linux-kernel thread:
http://lists.arm.linux.org.uk/lurker/message/20110718.103237.0106d468.en.htmlSigned-off-by: NBrian S. Julin <bri@abrij.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit fad10708 fixed the wrong test for MX51
as the MX51 addresses are wrong for MX50 and MX53 but now it's MX51 only,
UART_PADDR is not defined anymore when building for MX50/MX53.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: NSteev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

irq_to_gpio() is being called on a GPIO so change to using
gpio_to_irq() instead.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit 1eb19a12 ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work.  The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes).  So the assembly version would overwrite the
stack randomly.

The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around.  At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.
Reported-and-tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

arch/sparc/mm/init_64.c:1622:22: error: unused variable '__swapper_4m_tsb_phys_patch_end' [-Werror=unused-variable]
arch/sparc/mm/init_64.c:1621:22: error: unused variable '__swapper_4m_tsb_phys_patch' [-Werror=unused-variable]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

omap_sr_disable_reset_volt is called with irqs off in omapx_enter_sleep,
as part of idle sequence, this eventually calls sr_disable and
pm_runtime_put_sync. pm_runtime_put_sync calls rpm_idle, which will
enable interrupts in order to call the callback. In this short interval
when interrupts are enabled, scenarios such as the following can occur:
while interrupts are enabled, the timer interrupt that is supposed to
wake the device out of idle occurs and is acked, so when the CPU finally
goes to off, the timer is already gone, missing a wakeup event.

Further, as the documentation for runtime states:"
 However, subsystems can use the pm_runtime_irq_safe() helper function
 to tell the PM core that a device's ->runtime_suspend() and ->runtime_resume()
 callbacks should be invoked in atomic context with interrupts disabled
 (->runtime_idle() is still invoked the default way)."

Hence, replace pm_runtime_put_sync with pm_runtime_put_sync_suspend
to invoke the suspend handler and shut off the fclk for SmartReflex
module instead of using the idle handler in interrupt disabled context.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NColin Cross <ccross@google.com>
[khilman@ti.com: minor Subject edits]
Signed-off-by: NKevin Hilman <khilman@ti.com>

Board code should not touch omap_device internals.  To get the MPU/IVA devices,
use existing APIs: omap2_get_mpu_device(), omap2_get_iva_device().
Signed-off-by: NKevin Hilman <khilman@ti.com>