In commit 'c03abd84 ("net: ethernet: cpsw: don't requests
IRQs we don't use")', common isr is split into tx and rx, but
in rx isr tx interrupt is also disabledi in cpsw_disable_irq().
So tx interrupts are not handled during rx interrupts and rx
napi completion and results in poor tx performance by 40Mbps.
Fixing by disabling only rx interrupt in rx isr.

Cc: Felipe Balbi <balbi@ti.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() instead of calling random_ether_addr().
Here, this change is setting addr_assign_type to NET_ADDR_RANDOM.

The Coccinelle semantic patch that performs this transformation
is as follows:

@@
identifier a,b;
@@

-random_ether_addr(a->b);
+eth_hw_addr_random(a);
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Destroy minor_idr on module_exit, reclaiming the allocated memory.

This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@

module_init(init);

@ defines_module_exit @
identifier exit;
@@

module_exit(exit);

@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@

DEFINE_IDR(idr);

@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 idr_destroy(&idr);
 ...
}

@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 +idr_destroy(&idr);
}
</SmPL>
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree. This batch
mostly comes with patches to address fallout from the previous merge window
cycle, they are:

1) Use entry->state.hook_list from nf_queue() instead of the global nf_hooks
   which is not valid when used from NFPROTO_NETDEV, this should cause no
   problems though since we have no userspace queueing for that family, but
   let's fix this now for the sake of correctness. Patch from Eric W. Biederman.

2) Fix compilation breakage in bridge netfilter if CONFIG_NF_DEFRAG_IPV4 is not
   set, from Bernhard Thaler.

3) Use percpu jumpstack in arptables too, now that there's a single copy of the
   rule blob we can't store the return address there anymore. Patch from
   Florian Westphal.

4) Fix a skb leak in the xmit path of bridge netfilter, problem there since
   2.6.37 although it should be not possible to hit invalid traffic there, also
   from Florian.

5) Eric Leblond reports that when loading a large ruleset with many missing
   modules after a fresh boot, nf_tables can take long time commit it. Fix this
   by processing the full batch until the end, even on missing modules, then
   abort only once and restart processing.

6) Add bridge netfilter files to the MAINTAINER files.

7) Fix a net_device refcount leak in the new IPV6 bridge netfilter code, from
   Julien Grall.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The limit for BQL is updated each time we call
netdev_tx_completed_queue.
Without this patch the BQL limit was updated for every TX event we
see.
The issue was that this only updated the limit to handle the data
we complete in two events as the first event wouldn't show that
enough traffic had been processed between them.

This was OK when interrupt moderation was off but not when it was
on as more data had to be completed in a single interrupt.

The patch changes this so that we do report the completion to BQL
only when all the TX events in the interrupt have been processed.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NZheng Liu <zhliu@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As its first order of business, boomerang_interrupt() checks whether
the device really has any pending interrupts. If it does not,
it does nothing and returns, but it still returns IRQ_HANDLED.

This is wrong: interrupt was not handled, IRQ handlers of other
devices sharing this IRQ line need to be called.

vortex_interrupt() has it right: it returns IRQ_NONE in this case
via IRQ_RETVAL(0).

Do the same in boomerang_interrupt().
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vmxnet3's current napi path is built to count every rx descriptor we recieve,
and use that as a count of the napi budget.  That means its possible to return
from a napi poll halfway through recieving a fragmented packet accross multiple
dma descriptors.  If that happens, the next napi poll will start with the
descriptor ring in an improper state (e.g. the first descriptor we look at may
have the end-of-packet bit set), which will cause a BUG halt in the driver.

Fix the issue by only counting whole received packets in the napi poll and
returning that value, rather than the descriptor count.

Tested by the reporter and myself, successfully
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This kernel patch exports the value of the new
ignore_routes_with_linkdown via netconf.

v2: changes to notify userspace via netlink when sysctl values change
and proposed for 'net' since this could be considered a bugfix
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Suggested-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch avoids the double up_write to filter_sem if
efx_net_open() fails.

Resolves: 2d432f20Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit b0e9a30d ("bridge: Add vlan id to multicast groups")
there's a check in br_ip_equal() for a matching vlan id, but the mdb
functions were not modified to use (or at least zero it) so when an
entry was added it would have a garbage vlan id (from the local br_ip
variable in __br_mdb_add/del) and this would prevent it from being
matched and also deleted. So zero out the whole local ip var to protect
ourselves from future changes and also to fix the current bug, since
there's no vlan id support in the mdb uapi - use always vlan id 0.
Example before patch:
root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent
RTNETLINK answers: Invalid argument

After patch:
root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
Signed-off-by: NNikolay Aleksandrov <razor@blackwall.org>
Fixes: b0e9a30d ("bridge: Add vlan id to multicast groups")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When cpsw's number of slave is set to 1 in device tree and while
accessing second slave ndev and priv in cpsw_tx_interrupt(),
there is a kernel crash. This is due to cpsw_get_slave_priv()
not verifying number of slaves while retriving netdev priv and
returns a invalid memory region. Fixing the issue by introducing
number of slave check in cpsw_get_slave_priv() and
cpsw_get_slave_ndev().

[   15.879589] Unable to handle kernel paging request at virtual address 0f0e142c
[   15.888540] pgd = ed374000
[   15.891359] [0f0e142c] *pgd=00000000
[   15.895105] Internal error: Oops: 5 [#1] SMP ARM
[   15.899936] Modules linked in:
[   15.903139] CPU: 0 PID: 593 Comm: udhcpc Tainted: G        W       4.1.0-12205-gfda8b18c-dirty #10
[   15.912386] Hardware name: Generic AM43 (Flattened Device Tree)
[   15.918557] task: ed2a2e00 ti: ed3fe000 task.ti: ed3fe000
[   15.924187] PC is at cpsw_tx_interrupt+0x30/0x44
[   15.929008] LR is at _raw_spin_unlock_irqrestore+0x40/0x44
[   15.934726] pc : [<c048b9cc>]    lr : [<c05ef4f4>]    psr: 20000193
[   15.934726] sp : ed3ffc08  ip : ed2a2e40  fp : 00000000
[   15.946685] r10: c0969ce8  r9 : c0969cfc  r8 : 00000000
[   15.952129] r7 : 000000c6  r6 : ee54ab00  r5 : ee169c64  r4 : ee534e00
[   15.958932] r3 : 0f0e0d0c  r2 : 00000000  r1 : ed3ffbc0  r0 : 00000001
[   15.965735] Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[   15.973261] Control: 10c5387d  Table: ad374059  DAC: 00000015
[   15.979246] Process udhcpc (pid: 593, stack limit = 0xed3fe218)
[   15.985414] Stack: (0xed3ffc08 to 0xed400000)
[   15.989954] fc00:                   ee54ab00 c009928c c0a9e648 60000193 000032e4 ee169c00
[   15.998478] fc20: ee169c64 ee169c00 ee169c64 ee54ab00 00000001 00000001 ee67e268 ee008800
[   16.006995] fc40: ee534800 c009946c ee169c00 ee169c64 c08bd660 c009c370 c009c2a4 000000c6
[   16.015513] fc60: c08b75c4 c08b0854 00000000 c0098b3c 000000c6 c0098c50 ed3ffcb0 0000003a
[   16.024033] fc80: ed3ffcb0 fa24010c c08b7800 fa240100 ee7e9880 c00094c4 c05ef4e8 60000013
[   16.032556] fca0: ffffffff ed3ffce4 ee7e9880 c05ef964 00000001 ed2a33d8 00000000 ed2a2e00
[   16.041080] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800
[   16.049603] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff 00000001 00000001
[   16.058121] fd00: ee536bf8 c0487a04 00000000 00000000 ee534800 00000000 00000156 c048c990
[   16.066645] fd20: 00000000 00000000 c0969f40 00000000 00000000 c05000e8 00000001 00000000
[   16.075167] fd40: 00000000 c051eefc 00000000 ee67e268 00000000 00000000 ee51b800 ed3ffd9c
[   16.083690] fd60: 00000000 ee67e200 ee51b800 ee7e9880 ee67e268 00000000 00000000 ee67e200
[   16.092211] fd80: ee51b800 ee7e9880 ee67e268 ee534800 ee67e200 c051eedc ee67e268 00000010
[   16.100727] fda0: 00000000 00000000 ee7e9880 ee534800 00000000 ee67e268 ee51b800 c05006fc
[   16.109247] fdc0: ee67e268 00000001 c0500488 00000156 ee7e9880 00000000 ed3fe000 fffffff4
[   16.117771] fde0: ed3fff1c ee7e9880 ee534800 00000148 00000000 ed1f8340 00000000 00000000
[   16.126289] fe00: 00000000 c05a9054 00000000 00000000 00000156 c0ab62a8 00000010 ed3e7000
[   16.134812] fe20: 00000000 00000008 edcfb700 ed3fff1c c0fb5f94 ed2a2e00 c0fb5f64 000005d8
[   16.143336] fe40: c0a9b3b8 00000000 ed3e7070 00000000 00000000 00000000 00009f40 00000000
[   16.151858] fe60: 00000000 00020022 00110008 00000000 00000000 43004400 00000000 ffffffff
[   16.160374] fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   16.168898] fea0: edcfb700 bee5f380 00000014 00000000 ed3fe000 00000000 00004400 c04e2b64
[   16.177415] fec0: 00000002 c04e3b00 ed3ffeec 00000001 0000011a 00000000 00000000 bee5f394
[   16.185937] fee0: 00000148 ed3fff10 00000014 00000001 00000000 00000000 ed3ffee4 00000000
[   16.194459] ff00: 00000000 00000000 00000000 c04e3664 00080011 00000002 06000000 ffffffff
[   16.202980] ff20: 0000ffff ffffffff 0000ffff c008dd54 ee5a6f08 ee636e80 c096972d c0089c14
[   16.211499] ff40: 00000000 60000013 ee5a6f40 60000013 00000000 ee5a6f40 00000002 00000006
[   16.220023] ff60: 00000000 edcfb700 00000001 ed2a2e00 c000f60c 00000001 0000011a c008ea34
[   16.228540] ff80: 00000006 00000000 bee5f380 00000014 bee5f380 00000014 bee5f380 00000122
[   16.237059] ffa0: c000f7c4 c000f5e0 bee5f380 00000014 00000006 bee5f394 00000148 00000000
[   16.245581] ffc0: bee5f380 00000014 bee5f380 00000122 fffffd6e 00004300 00004800 00004400
[   16.254104] ffe0: bee5f378 bee5f36c 000307ec b6f39044 40000010 00000006 ed36fa40 00000000
[   16.262642] [<c048b9cc>] (cpsw_tx_interrupt) from [<c009928c>] (handle_irq_event_percpu+0x64/0x204)
[   16.272076] [<c009928c>] (handle_irq_event_percpu) from [<c009946c>] (handle_irq_event+0x40/0x64)
[   16.281330] [<c009946c>] (handle_irq_event) from [<c009c370>] (handle_fasteoi_irq+0xcc/0x1a8)
[   16.290220] [<c009c370>] (handle_fasteoi_irq) from [<c0098b3c>] (generic_handle_irq+0x20/0x30)
[   16.299197] [<c0098b3c>] (generic_handle_irq) from [<c0098c50>] (__handle_domain_irq+0x64/0xdc)
[   16.308273] [<c0098c50>] (__handle_domain_irq) from [<c00094c4>] (gic_handle_irq+0x20/0x60)
[   16.316987] [<c00094c4>] (gic_handle_irq) from [<c05ef964>] (__irq_svc+0x44/0x5c)
[   16.324779] Exception stack(0xed3ffcb0 to 0xed3ffcf8)
[   16.330044] fca0:                                     00000001 ed2a33d8 00000000 ed2a2e00
[   16.338567] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800
[   16.347090] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff
[   16.353987] [<c05ef964>] (__irq_svc) from [<c05ef4e8>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[   16.362973] [<c05ef4e8>] (_raw_spin_unlock_irqrestore) from [<c0487a04>] (cpdma_check_free_tx_desc+0x60/0x6c)
[   16.373311] [<c0487a04>] (cpdma_check_free_tx_desc) from [<c048c990>] (cpsw_ndo_start_xmit+0xb4/0x1ac)
[   16.383017] [<c048c990>] (cpsw_ndo_start_xmit) from [<c05000e8>] (dev_hard_start_xmit+0x2a4/0x4c0)
[   16.392364] [<c05000e8>] (dev_hard_start_xmit) from [<c051eedc>] (sch_direct_xmit+0xf4/0x210)
[   16.401246] [<c051eedc>] (sch_direct_xmit) from [<c05006fc>] (__dev_queue_xmit+0x2ac/0x7bc)
[   16.409960] [<c05006fc>] (__dev_queue_xmit) from [<c05a9054>] (packet_sendmsg+0xc68/0xeb4)
[   16.418585] [<c05a9054>] (packet_sendmsg) from [<c04e2b64>] (sock_sendmsg+0x14/0x24)
[   16.426663] [<c04e2b64>] (sock_sendmsg) from [<c04e3b00>] (SyS_sendto+0xb4/0xe0)
[   16.434377] [<c04e3b00>] (SyS_sendto) from [<c000f5e0>] (ret_fast_syscall+0x0/0x54)
[   16.442360] Code: e5943118 e593303c e3530000 0a000002 (e5930720)
[   16.448716] ---[ end trace a68159f094d85ba6 ]---
[   16.453526] Kernel panic - not syncing: Fatal exception in interrupt
[   16.460149] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling connect() with an AF_TIPC socket would trigger a series
of error messages from SELinux along the lines of:
SELinux: Invalid class 0
type=AVC msg=audit(1434126658.487:34500): avc:  denied  { <unprintable> }
  for pid=292 comm="kworker/u16:5" scontext=system_u:system_r:kernel_t:s0
  tcontext=system_u:object_r:unlabeled_t:s0 tclass=<unprintable>
  permissive=0

This was due to a failure to initialize the security state of the new
connection sock by the tipc code, leaving it with junk in the security
class field and an unlabeled secid.  Add a call to security_sk_clone()
to inherit the security state from the parent socket.
Reported-by: NTim Shearer <tim.shearer@overturenetworks.com>
Signed-off-by: NStephen Smalley <sds@tycho.nsa.gov>
Acked-by: NPaul Moore <paul@paul-moore.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shradha Shah says:

====================
sfc: compat for lack of VADAPTOR_SET_MAC in adaptor_firmware <= 4.1.1.1023

This patch series resolves an incompatibility with legacy
firmware due to the lack of MC_CMD_VADAPTOR_SET_MAC in
adaptor_firmware <= 4.1.1.1023

Unless this patch series is applied there will be a compatibility
issue between the driver and Solarflare adapters running older
firmware.

Tested with and without CONFIG_SFC_SRIOV
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some versions of MCFW do not support the MC_CMD_VADAPTOR_SET_MAC
command, and ENOSYS will be returned.

If the PF created its own vport, the function's datapath must be
stopped and the vport can be reconfigured to reflect the new MAC
address.

If the MCFW created the vport for the PF (which is the case when
the nic_data->vport_mac is blank), nothing further needs to be
done as the vport is not under the control of the PF.

This only applies to PFs because the MCFW in question does not
support VFs.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-organize the structure of error handling to avoid having
to duplicate the netif_err() around the ifdefs.

The only change to the behaviour of the error-handling is that
the PF's data structure to record VF details should only be
updated if the original command succeeded.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When "primary_reselect" is set to "failure", primary interface should
not become active until current active slave is down. But if we set first
member of bond device as a "primary" interface and "primary_reselect"
is set to "failure" then whenever primary interface's link get back(up)
it become active slave even if current active slave is still up.

With this patch, "bond_find_best_slave" will not traverse members if
primary interface is not candidate for failover/reselection and current
active slave is still up.
Signed-off-by: NMazhar Rana <mazhar.rana@cyberoam.com>
Signed-off-by: NJay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frag needed should be sent only if the inner header asked
to not fragment. Currently fragmentation is broken if the
tunnel has df set, but df was not asked in the original
packet. The tunnel's df needs to be still checked to update
internally the pmtu cache.

Commit 23a3647b broke it, and this commit fixes
the ipv4 df check back to the way it was.

Fixes: 23a3647b ("ip_tunnels: Use skb-len to PMTU check.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jason Gunthorpe reported that since commit c02db8c6 ("rtnetlink: make
SR-IOV VF interface symmetric"), we don't verify IFLA_VF_INFO attributes
anymore with respect to their policy, that is, ifla_vfinfo_policy[].

Before, they were part of ifla_policy[], but they have been nested since
placed under IFLA_VFINFO_LIST, that contains the attribute IFLA_VF_INFO,
which is another nested attribute for the actual VF attributes such as
IFLA_VF_MAC, IFLA_VF_VLAN, etc.

Despite the policy being split out from ifla_policy[] in this commit,
it's never applied anywhere. nla_for_each_nested() only does basic nla_ok()
testing for struct nlattr, but it doesn't know about the data context and
their requirements.

Fix, on top of Jason's initial work, does 1) parsing of the attributes
with the right policy, and 2) using the resulting parsed attribute table
from 1) instead of the nla_for_each_nested() loop (just like we used to
do when still part of ifla_policy[]).

Reference: http://thread.gmane.org/gmane.linux.network/368913
Fixes: c02db8c6 ("rtnetlink: make SR-IOV VF interface symmetric")
Reported-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Rony Efraim <ronye@mellanox.com>
Cc: Vlad Zolotarov <vladz@cloudius-systems.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a switch is attached to the mdio bus, the mdio bus can be used
while the interface is not open. If the IPG clock is not enabled, MDIO
reads/writes will simply time out.

Add support for runtime PM to control this clock. Enable/disable this
clock using runtime PM, with open()/close() and mdio read()/write()
function triggering runtime PM operations. Since PM is optional, the
IPG clock is enabled at probe and is no longer modified by
fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is
guaranteed the clock is running when MDIO operations are performed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running a kernel configured with CONFIG_DMA_API_DEBUG=y a warning
is issued:
  DMA-API: device driver tries to sync DMA memory it has not allocated

This warning is the result of mapping the full range of the Rx buffer
pages allocated and then performing a dma_sync_single_for_cpu against
a calculated DMA address. The proper thing to do is to use the
dma_sync_single_range_for_cpu with a base DMA address and an offset.
Reported-by: NKim Phillips <kim.phillips@arm.com>
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Tested-by: NKim Phillips <kim.phillips@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit e1622baf.

The side effect of this commit is to add a '@NONE' after each virtual
interface name with a 'ip link'. It may break existing scripts.
Reported-by: NOlivier Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

User space can crash kernel with

ip link add ifb10 numtxqueues 100000 type ifb

We must replace a BUG_ON() by proper test and return -EINVAL for
crazy values.

Fixes: 60877a32 ("net: allow large number of tx queues")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If rhashtable_walk_next detects a resize operation in progress, it jumps
to the new table and continues walking that one. But it misses to drop
the reference to it's current item, leading it to continue traversing
the new table's bucket in which the current item is sorted into, and
after reaching that bucket's end continues traversing the new table's
second bucket instead of the first one, thereby potentially missing
items.

This fixes the rhashtable runtime test for me. Bug probably introduced
by Herbert Xu's patch eddee5ba ("rhashtable: Fix walker behaviour during
rehash") although not explicitly tested.

Fixes: eddee5ba ("rhashtable: Fix walker behaviour during rehash")
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Start the delete timer when adding temp static entries so they can expire.
Signed-off-by: NSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: ccb1c31a ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On UML builds, mdio-mux-mmioreg.c fails to compile:

drivers/net/phy/mdio-mux-mmioreg.c:50:3: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
drivers/net/phy/mdio-mux-mmioreg.c:63:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]

This is due to CONFIG_OF now being user selectable. Add a dependency on
HAS_IOMEM to fix this.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 1d5da757 (ax25: Stop using magic
neighbour cache operations.) any attempt to transmit IP packets over
a bpqether device will result in a message like "Dead loop on virtual
device bpq0, fix it urgently!"

Fix suggested by Eric W. Biederman <ebiederm@xmission.com>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: <stable@vger.kernel.org> # 4.1
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rate estimators are limited to 4 Mpps, which was fine years ago, but
too small with current hardware generation.

Lets use 2^5 scaling instead of 2^10 to get 128 Mpps new limit.

On 64bit arch, use an "unsigned long" for temp storage and remove limit.
(We do not expect 32bit arches to be able to reach this point)

Tested:

tc -s -d filter sh dev eth0 parent ffff:

filter protocol ip pref 1 u32
filter protocol ip pref 1 u32 fh 800: ht divisor 1
filter protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:15
  match 07000000/ff000000 at 12
	action order 1: gact action drop
	 random type none pass val 0
	 index 1 ref 1 bind 1 installed 166 sec
 	Action statistics:
	Sent 39734251496 bytes 863788076 pkt (dropped 863788117, overlimits 0 requeues 0)
	rate 4067Mbit 11053596pps backlog 0b 0p requeues 0
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit efb6de9b "netfilter: bridge:
forward IPv6 fragmented packets" introduced a new function
br_validate_ipv6 which take a reference on the inet6 device. Although,
the reference is not released at the end.

This will result to the impossibility to destroy any netdevice using
ipv6 and bridge.

It's possible to directly retrieve the inet6 device without taking a
reference as all netfilter hooks are protected by rcu_read_lock via
nf_hook_slow.

Spotted while trying to destroy a Xen guest on the upstream Linux:
"unregister_netdevice: waiting for vif1.0 to become free. Usage count = 1"
Signed-off-by: NJulien Grall <julien.grall@citrix.com>
Cc: Bernhard Thaler <bernhard.thaler@wvnet.at>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: fw@strlen.de
Cc: ian.campbell@citrix.com
Cc: wei.liu2@citrix.com
Cc: Bob Liu <bob.liu@oracle.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

So scripts/get_maintainer.pl shows the Netfilter mailing lists.
Reported-by: NJulien Grall <julien.grall@citrix.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Part of commit 49aa284fe64c4c1 ("cxgb4: Add support for devlog")
change introduced a real bug where the Device Log Sequence Numbers are
no longer being converted from firmware Big-Endian to local CPU-Endian
format.

This patch moves all of the translation into the devlog_show() routine.
The only endianness code now in devlog_open() is the small loop to find the
earliest (lowest Sequence Number) Device Log entry in the circular buffer.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before commit daad1512 ("ipv6: Make ipv6_is_mld() inline and use it
from ip6_mc_input().") MLD packets were only processed locally. After the
change, a copy of MLD packet goes through ip6_mr_input, causing
MRT6MSG_NOCACHE message to be generated to user space.

Make MLD packet only processed locally.

Fixes: daad1512 ("ipv6: Make ipv6_is_mld() inline and use it from ip6_mc_input().")
Signed-off-by: NHermin Anggawijaya <hermin.anggawijaya@alliedtelesis.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The module_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The module_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The free_percpu() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vlan ids 0 and 4095 were disallowed by commit:
8adff41c ("bridge: Don't use VID 0 and 4095 in vlan filtering")
but then the check was removed when vlan ranges were introduced by:
bdced7ef ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
So reintroduce the vlan range check.
Before patch:
[root@testvm ~]# bridge vlan add vid 0 dev eth0 master
(succeeds)
After Patch:
[root@testvm ~]# bridge vlan add vid 0 dev eth0 master
RTNETLINK answers: Invalid argument
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: bdced7ef ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
Acked-by: NToshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2015-07-02

A couple of regressions crept in because of a patch to use proper list
APIs rather than manually reading & writing the next/prev pointers
(commit 835a6a2f). Turns out this was
masking a few bugs: a missing INIT_LIST_HEAD() call and incorrectly
using list_del() rather than list_del_init(). The two patches in this
set fix these, and it'd be nice they could still make it to 4.2-rc1 to
avoid new bug reports from users.

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In enic_poll, we clean tx and rx queues, when low latency busy socket polling
is happening, enic_poll will only clean tx queue. After cleaning tx, it should
return total budget for re-poll.

There is a small window between vnic_intr_unmask() and enic_poll_unlock_napi().
In this window if an irq occurs and napi is scheduled on different cpu, it tries
to acquire enic_poll_lock_napi() and fails. Unlock napi_poll before unmasking
the interrupt.

v2:
Do not change tx wonk done behaviour. Consider only rx work done for completing
napi.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull init.h/module.h fragility fixes from Paul Gortmaker:
 "Fixup various init.h misuses that are fragile wrt code moving to
  module.h

  What started as a removal of no longer required include <linux/init.h>
  due to the earlier __cpuinit and __devinit removal led to the
  observation that some module specfic support was living in init.h
  itself, thus preventing the full removal from introducing compile
  regressions.

  This series includes a few final fixups needed prior to the relocation
  of the modular init code from <init.h> to <module.h>.  These are
  things that weren't easily categorized into any of the other previous
  series categories already requested for pull.

  That said, each fixup branch (including this one) is independent and
  there are no ordering constraints.  Only the final code relocation
  (which is NOT in this pull) requires that all my cleanup branches be
  merged first"

* tag 'module-misc-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  tile: add init.h to usb.c to avoid compile failure
  arm: fix implicit #include <linux/init.h> in entry asm.
  x86: replace __init_or_module with __init in non-modular vsmp_64.c