Those are simply giving information about the current
state of the UDC, nothing really fancy. We can let
everybody read those.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_gadget_disconnect() is responsible of removing
data pullups. Before doing that we must, first, tell
gadget driver we're disconnecting (by calling disconnect
method on gadget driver structure), unbind the gadget
driver and stop the controller.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

that has already being done by udc-core.c. It's
unnecessary and might cause issues with some gadget
drivers.

Tested: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed.  The idle callback routine could
then schedule a delayed suspend for some time later.

However this behavior was changed by commit
f71648d7 (PM / Runtime: Remove idle
notification after failing suspend).  No notifications were sent, and
there was no clear mechanism to retry failed suspends.

This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down.  A companion
patch changes the PM core's behavior, but we also need to change the
USB core.  In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

I noticed on my Panther Point system that I wasn't getting hotplug events
for my usb3.0 disk on a usb3 port.  I tracked it down to the fact that the
system had the warm reset change bit still set.  This seemed to block future
events from being received, including a hotplug event.

Clearing this bit during initialization allowed the hotplug event to be
received and the disk to be recognized correctly.

This patch should be backported to kernels as old as 2.6.39.
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Matt's AsMedia xHCI host controller was responding with a Context Error
to an address device command after a configured device reset.  Some
sequence of events leads both the slot and endpoint zero add flags
cleared to zero, which the AsMedia host doesn't like:

[  223.701839] xhci_hcd 0000:03:00.0: Slot ID 1 Input Context:
[  223.701841] xhci_hcd 0000:03:00.0: @ffff880137b25000 (virt) @ffffc000 (dma) 0x000000 - drop flags
[  223.701843] xhci_hcd 0000:03:00.0: @ffff880137b25004 (virt) @ffffc004 (dma) 0x000000 - add flags
[  223.701846] xhci_hcd 0000:03:00.0: @ffff880137b25008 (virt) @ffffc008 (dma) 0x000000 - rsvd2[0]
[  223.701848] xhci_hcd 0000:03:00.0: @ffff880137b2500c (virt) @ffffc00c (dma) 0x000000 - rsvd2[1]
[  223.701850] xhci_hcd 0000:03:00.0: @ffff880137b25010 (virt) @ffffc010 (dma) 0x000000 - rsvd2[2]
[  223.701852] xhci_hcd 0000:03:00.0: @ffff880137b25014 (virt) @ffffc014 (dma) 0x000000 - rsvd2[3]
[  223.701854] xhci_hcd 0000:03:00.0: @ffff880137b25018 (virt) @ffffc018 (dma) 0x000000 - rsvd2[4]
[  223.701857] xhci_hcd 0000:03:00.0: @ffff880137b2501c (virt) @ffffc01c (dma) 0x000000 - rsvd2[5]
[  223.701858] xhci_hcd 0000:03:00.0: Slot Context:
[  223.701860] xhci_hcd 0000:03:00.0: @ffff880137b25020 (virt) @ffffc020 (dma) 0x8400000 - dev_info
[  223.701862] xhci_hcd 0000:03:00.0: @ffff880137b25024 (virt) @ffffc024 (dma) 0x010000 - dev_info2
[  223.701864] xhci_hcd 0000:03:00.0: @ffff880137b25028 (virt) @ffffc028 (dma) 0x000000 - tt_info
[  223.701866] xhci_hcd 0000:03:00.0: @ffff880137b2502c (virt) @ffffc02c (dma) 0x000000 - dev_state
[  223.701869] xhci_hcd 0000:03:00.0: @ffff880137b25030 (virt) @ffffc030 (dma) 0x000000 - rsvd[0]
[  223.701871] xhci_hcd 0000:03:00.0: @ffff880137b25034 (virt) @ffffc034 (dma) 0x000000 - rsvd[1]
[  223.701873] xhci_hcd 0000:03:00.0: @ffff880137b25038 (virt) @ffffc038 (dma) 0x000000 - rsvd[2]
[  223.701875] xhci_hcd 0000:03:00.0: @ffff880137b2503c (virt) @ffffc03c (dma) 0x000000 - rsvd[3]
[  223.701877] xhci_hcd 0000:03:00.0: Endpoint 00 Context:
[  223.701879] xhci_hcd 0000:03:00.0: @ffff880137b25040 (virt) @ffffc040 (dma) 0x000000 - ep_info
[  223.701881] xhci_hcd 0000:03:00.0: @ffff880137b25044 (virt) @ffffc044 (dma) 0x2000026 - ep_info2
[  223.701883] xhci_hcd 0000:03:00.0: @ffff880137b25048 (virt) @ffffc048 (dma) 0xffffe8e0 - deq
[  223.701885] xhci_hcd 0000:03:00.0: @ffff880137b25050 (virt) @ffffc050 (dma) 0x000000 - tx_info
[  223.701887] xhci_hcd 0000:03:00.0: @ffff880137b25054 (virt) @ffffc054 (dma) 0x000000 - rsvd[0]
[  223.701889] xhci_hcd 0000:03:00.0: @ffff880137b25058 (virt) @ffffc058 (dma) 0x000000 - rsvd[1]
[  223.701892] xhci_hcd 0000:03:00.0: @ffff880137b2505c (virt) @ffffc05c (dma) 0x000000 - rsvd[2]
...
[  223.701927] xhci_hcd 0000:03:00.0: // Ding dong!
[  223.701992] xhci_hcd 0000:03:00.0: Setup ERROR: address device command for slot 1.

The xHCI spec says that both flags must be set to one for the Address
Device command.  When the device is first enumerated,
xhci_setup_addressable_virt_dev() does set those flags.  However, when
the device is addressed after it has been reset in the configured state,
xhci_setup_addressable_virt_dev() is not called, and
xhci_copy_ep0_dequeue_into_input_ctx() is called instead.  That function
relies on the flags being set up by previous commands, which apparently
isn't a good assumption.

Move the setting of the flags into the common parent function.

This should be queued for stable kernels as old as 2.6.35, since that
was the first introduction of xhci_copy_ep0_dequeue_into_input_ctx.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMatt <mdm@iinet.net.au>
Cc: stable@vger.kernel.org

While debugging a usb3 problem, I stumbled upon this lockdep warning.

Oct 18 21:41:17 dhcp47-74 kernel: =================================
Oct 18 21:41:17 dhcp47-74 kernel: [ INFO: inconsistent lock state ]
Oct 18 21:41:17 dhcp47-74 kernel: 3.1.0-rc4nmi+ #456
Oct 18 21:41:17 dhcp47-74 kernel: ---------------------------------
Oct 18 21:41:17 dhcp47-74 kernel: inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
Oct 18 21:41:17 dhcp47-74 kernel: swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
Oct 18 21:41:17 dhcp47-74 kernel: (&(&xhci->lock)->rlock){?.-...}, at: [<ffffffffa0228990>] xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: {IN-HARDIRQ-W} state was registered at:
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8109a941>] __lock_acquire+0x781/0x1660
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8109bed7>] lock_acquire+0x97/0x170
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff81501b46>] _raw_spin_lock+0x46/0x80
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffffa02299fa>] xhci_irq+0x3a/0x1960 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffffa022b351>] xhci_msi_irq+0x31/0x40 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff810d2305>] handle_irq_event_percpu+0x85/0x320
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff810d25e8>] handle_irq_event+0x48/0x70
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff810d537d>] handle_edge_irq+0x6d/0x130
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff810048c9>] handle_irq+0x49/0xa0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8150d56d>] do_IRQ+0x5d/0xe0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff815029b0>] ret_from_intr+0x0/0x13
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff81388aca>] usb_set_device_state+0x8a/0x180
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8138f038>] usb_add_hcd+0x2b8/0x730
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffffa022ed7e>] xhci_pci_probe+0x9e/0xd4 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8127915f>] local_pci_probe+0x5f/0xd0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8127a569>] pci_device_probe+0x119/0x120
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff81334473>] driver_probe_device+0xa3/0x2c0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8133473b>] __driver_attach+0xab/0xb0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8133373c>] bus_for_each_dev+0x6c/0xa0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff813341fe>] driver_attach+0x1e/0x20
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff81333b88>] bus_add_driver+0x1f8/0x2b0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff81334df6>] driver_register+0x76/0x140
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8127a7c6>] __pci_register_driver+0x66/0xe0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffffa013c04a>] snd_timer_find+0x4a/0x70 [snd_timer]
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffffa013c00e>] snd_timer_find+0xe/0x70 [snd_timer]
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff810001d3>] do_one_initcall+0x43/0x180
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff810a9ed2>] sys_init_module+0x92/0x1f0
Oct 18 21:41:17 dhcp47-74 kernel:  [<ffffffff8150ab6b>] system_call_fastpath+0x16/0x1b
Oct 18 21:41:17 dhcp47-74 kernel: irq event stamp: 631984
Oct 18 21:41:17 dhcp47-74 kernel: hardirqs last  enabled at (631984): [<ffffffff81502720>] _raw_spin_unlock_irq+0x30/0x50
Oct 18 21:41:17 dhcp47-74 kernel: hardirqs last disabled at (631983): [<ffffffff81501c49>] _raw_spin_lock_irq+0x19/0x90
Oct 18 21:41:17 dhcp47-74 kernel: softirqs last  enabled at (631980): [<ffffffff8105ff63>] _local_bh_enable+0x13/0x20
Oct 18 21:41:17 dhcp47-74 kernel: softirqs last disabled at (631981): [<ffffffff8150ce6c>] call_softirq+0x1c/0x30
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: other info that might help us debug this:
Oct 18 21:41:17 dhcp47-74 kernel: Possible unsafe locking scenario:
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel:       CPU0
Oct 18 21:41:17 dhcp47-74 kernel:       ----
Oct 18 21:41:17 dhcp47-74 kernel:  lock(&(&xhci->lock)->rlock);
Oct 18 21:41:17 dhcp47-74 kernel:  <Interrupt>
Oct 18 21:41:17 dhcp47-74 kernel:    lock(&(&xhci->lock)->rlock);
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: *** DEADLOCK ***
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: 1 lock held by swapper/0:
Oct 18 21:41:17 dhcp47-74 kernel: #0:  (&ep->stop_cmd_timer){+.-...}, at: [<ffffffff8106abf2>] run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: stack backtrace:
Oct 18 21:41:17 dhcp47-74 kernel: Pid: 0, comm: swapper Tainted: G        W   3.1.0-rc4nmi+ #456
Oct 18 21:41:17 dhcp47-74 kernel: Call Trace:
Oct 18 21:41:17 dhcp47-74 kernel: <IRQ>  [<ffffffff81098ed7>] print_usage_bug+0x227/0x270
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810999c6>] mark_lock+0x346/0x410
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109a7de>] __lock_acquire+0x61e/0x1660
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81099893>] ? mark_lock+0x213/0x410
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109bed7>] lock_acquire+0x97/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] ? xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81501b46>] _raw_spin_lock+0x46/0x80
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] ? xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106abf2>] ? run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106ac9d>] run_timer_softirq+0x20d/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106abf2>] ? run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228960>] ? xhci_queue_isoc_tx_prepare+0x8e0/0x8e0 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810604d2>] __do_softirq+0xf2/0x3f0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81020edd>] ? lapic_next_event+0x1d/0x30
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81090d4e>] ? clockevents_program_event+0x5e/0x90
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150ce6c>] call_softirq+0x1c/0x30
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8100484d>] do_softirq+0x8d/0xc0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8105ff35>] irq_exit+0xe5/0x100
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150d65e>] smp_apic_timer_interrupt+0x6e/0x99
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150b6f0>] apic_timer_interrupt+0x70/0x80
Oct 18 21:41:17 dhcp47-74 kernel: <EOI>  [<ffffffff81095d8d>] ? trace_hardirqs_off+0xd/0x10
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff812ddb76>] ? acpi_idle_enter_bm+0x227/0x25b
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff812ddb71>] ? acpi_idle_enter_bm+0x222/0x25b
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff813eda63>] cpuidle_idle_call+0x103/0x290
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81002155>] cpu_idle+0xe5/0x160
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff814e7f50>] rest_init+0xe0/0xf0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff814e7e70>] ? csum_partial_copy_generic+0x170/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8e23>] start_kernel+0x3fc/0x407
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8321>] x86_64_start_reservations+0x131/0x135
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8412>] x86_64_start_kernel+0xed/0xf4
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: xHCI host not responding to stop endpoint command.
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: Assuming host is dying, halting host.
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: HC died; cleaning up
Oct 18 21:41:17 dhcp47-74 kernel: usb 3-4: device descriptor read/8, error -110
Oct 18 21:41:17 dhcp47-74 kernel: usb 3-4: device descriptor read/8, error -22
Oct 18 21:41:17 dhcp47-74 kernel: hub 3-0:1.0: cannot disable port 4 (err = -19)

Basically what is happening is in xhci_stop_endpoint_command_watchdog()
the xhci->lock is grabbed with just spin_lock.  What lockdep deduces is
that if an interrupt occurred while in this function it would deadlock
with xhci_irq because that function also grabs the xhci->lock.

Fixing it is trivial by using spin_lock_irqsave instead.

This should be queued to stable kernels as far back as 2.6.33.
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

To fix this build error on ARM:

drivers/usb/host/xhci-hub.c: In function 'xhci_stop_device':
drivers/usb/host/xhci-hub.c:261: error: 'GFP_NOIO' undeclared (first use in this function)
make[4]: *** [drivers/usb/host/xhci-hub.o] Error 1
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.

Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Now that no driver any longer depends on the CONFIG_SOC_AU1???  symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files.  Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration.  I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 drivers/usb/host/alchemy-common.c

usbhs_pkt_push() had inconsistent return under spin lock.
This patch fix it up.
Special thanks to Dan

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Properly triggering the reset wire is necessary with the ISP1761 used
on Terasic DE4 Altera-FPGA boards using a NIOS2 processor, for example.

This is an optional implementation for the OF binding only. The other
bindings just pass an invalid GPIO to the isp1760_register() routine.

Example, usage in DTS:
        gpios = <&pio_isp1761rst_0 0 1>;
to point to a GPIO controller from within the ISP1761 node: GPIO 0, active low.
Signed-off-by: NJoachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a small memory leak on the error paths.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

! has higher precedence than >= and since neither 0 nor 1 are greater
than 8 the condition is always false.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For USB CONTROL transaction, when the data length is zero,
the IN package is needed to finish this transaction in status stage.
Signed-off-by: NJerry Huang <r66093@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch tidyup below smatch complaint

drivers/usb/renesas_usbhs/mod_host.c +447 usbhsh_endpoint_free()
	 warn: variable dereferenced before check 'uep' (see line 444)

Special thanks to Dan
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For FSL PPC SoCs USB_ARCH_HAS_EHCI currently on depends on PPC_83xx.
However that excludes support for USB on 85xx & QorIQ devices.  Use
FSL_SOC insted which will get us 83xx, 85xx, QorIQ, and 5xxx which all
have the same USB IP on them.
Signed-off-by: NXulei <B33228@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1489) works around a hardware bug in MosChip EHCI
controllers.  Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter).  If the register is read at just the wrong time, the value
obtained is too low by 8.

When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0.  This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NJason N Pitt <jpitt@fhcrc.org>
CC: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a race, reproduced rarely if you unload the module
when host finishes mass storage device initialization (reading
partition table and so on): fsg_unbind() code first closes
lun files then waits for worker thread to finish its work, as
the result the thread may operate on already closed device
with an oops and backtrace:

[  484.937225] [<b00e403c>] (touch_atime+0x4/0x140) from [<b00a1498>] (generic_file_aio_read+0x678/0x6f0)
[  484.946563] [<b00a1498>] (generic_file_aio_read+0x678/0x6f0) from [<b00d08c4>] (do_sync_read+0xb0/0xf4)
[  484.955963] [<b00d08c4>] (do_sync_read+0xb0/0xf4) from [<b00d1478>] (vfs_read+0xac/0x144)
[  484.964172] [<b00d1478>] (vfs_read+0xac/0x144) from [<af24c6a8>] (fsg_setup+0x7f4/0x900 [g_file_storage])
[  484.973785] [<af24c6a8>] (fsg_setup+0x7f4/0x900 [g_file_storage]) from [<af24da14>] (fsg_main_thread+0x85c/0x175c [g_file_storage])
[  484.985626] [<af24da14>] (fsg_main_thread+0x85c/0x175c [g_file_storage]) from [<b0077c48>] (kthread+0x7c/0x84)
[  484.995666] [<b0077c48>] (kthread+0x7c/0x84) from [<b002f950>] (kernel_thread_exit+0x0/0x8)
[  485.004028] Code: eaffffd0 e28dd008 e8bd8df0 e92d40f7 (e591400c)

Change the order in unbind: wait for the thread first, then close
the files.
Signed-off-by: NYauheni Kaliuta <yauheni.kaliuta@nokia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NUwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NUwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NUwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NUwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NUwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NUwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To be able to use the driver on other OF-aware architectures, too.
And add necessary OF related #includes to fix compilation error.
Signed-off-by: NJoachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.

Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: NPeter Stuge <peter@stuge.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

At least some OHCI hardware (such as the MCP89) fails to flag any change
in the host status register or the port status registers when receiving
a remote wakeup while in D3 state. This results in the controller being
resumed but no device state change being noticed, at which point the
controller is put back to sleep again. Since there doesn't seem to be any
reliable way to identify the state change, just unconditionally resume the
hub. It'll be put back to sleep in the near future anyway if there are no
active devices attached to it.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To add USB 3.0 link power management (LPM), we need to know what the U1
and U2 exit latencies are for the xHCI host controller.  External USB 3.0
hubs report these values through the SuperSpeed Capabilities descriptor in
the BOS descriptor.  Make the USB 3.0 roothub for the xHCI host behave
like an external hub and return the BOS descriptors.

The U1 and U2 exit latencies will vary across each host controller, so we
need to dynamically fill those values in by reading the exit latencies out
of the xHC registers.  Make the roothub code in the USB core handle
hub_control() returning the length of the data copied.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver provides two functions in one configuration:
a mass storage, and a ACM (serial port) link.
Heavily based on multi.c and cdc2.c
Signed-off-by: NKlaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

| drivers/usb/gadget/mv_udc_core.c: In function 'handle_setup_packet':
| drivers/usb/gadget/mv_udc_core.c:1556:6: warning: 'status' may be \
	used uninitialized in this function
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch is going to support clock gating when vbus detection is
posible. Clock and phy will be on only when usb gadget is used(vbus valid).
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add test mode support for marvell udc driver.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

use DMA API for status_req's dma address, it is needed by dtd.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The controller will prime failure sometimes when do the iperf test.
Add delay to wait controller release dtd dma before we free it.
Then the issue is gone.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

put the device in idle when shutdown.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch is going to correct the ep0 state, and the unexpected
ep0 package warning can be removed.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>