v1.1 allows finer grained tuning of the SSC (spread-spectrum-clocking)
settings for SAS and SATA.  See notes in probe_roms.h
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fixes bug where max_concurr_spinup oem parameter should be
overriden by max_concurr_spinup user parameter. Override should
happen only when max_concurr_spinup user parameter is specified
in command line (greater than 0). Also this fix shortens variables
representing max_conxurr_spinup for oem and user parameters.
Signed-off-by: NAndrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_.  The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.

Also unwind the 'sds1' out of the parameter structs.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost).  Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

We can call the EFI get_variable service routine directly to retrieve
the EFI variable that holds the OEM parameters table.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

* Move port configuration agent implementation
* Merge core/scic_sds_port.[ch] into port.[ch]
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

cross driver constants are spread out over multiple header files, consolidate
them into isci.h, and push some includes out to the source files that need
them.

TODO: remove SCI_MODE_SIZE infrastructure.
TODO: task.h is full of inlines that are too large
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The element_length is 2 bytes.
Reported-by: NYinghai Lu <yinghai.lu@oracle.com>
Acked-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Converting the all CAPS data types to lower case.
Reported-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The original apc mode definition is the correct one, the fix from commit
4711ba10 "isci: fix oem parameter initialization and mode detection" was based
on a typo from a specification update.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

1/ Since commit 858d4aa7 "isci: Move firmware loading to per PCI device" we have
   been silently falling back to built-in defaults for the parameter settings by
   skipping the call to scic_oem_parameters_set().

2/ The afe parameters from the firmware were not being honored

3/ The latest oem parameter definition flips the mode_type values which are
   now 0: for APC 1: for MPC.  For APC we need to make sure all the phys
   default to the same address otherwise strict_wide_ports will cause duplicate
   domains.

4/ Fix up the driver announcement to indicate the source of the
   parameters.

5/ Fix up the sas addresses to be unique per controller (in the fallback case)
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Updating the EFI variable OEM parameter retrieval after examining the EFI
variable exported via sysfs.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Added fixups for the OROM parsing code after testing with BIOS OROM
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

These are the finalized values that the driver can expect to see in
production.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

1/ add OEM paramater support for mode_type (MPC vs APC)
2/ add OEM parameter support for max_number_concurrent_device_spin_up
3/ cleanup scic_sds_controller_start_next_phy

todo: hook up the amp control afe parameters into the afe init code
Signed-off-by: NHenryk Dembkowski <henryk.dembkowski@intel.com>
Signed-off-by: NJacek Danecki <Jacek.Danecki@intel.com>
[cleaned up scic_sds_controller_start_next_phy]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Adding EFI variable retrieving for OEM parameters. Still need GUID and
variable name.

Also updated the data struct for oem parameters and hex file for firmware
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
[fix CONFIG_EFI=n compile error]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

We need to scan the OROM for signature and grab the OEM parameters. We
also need to do the same for EFI. If all fails then we resort to user
binary blob, and if that fails then we go to the defaults.

Share the format with the create_fw utility so that all possible sources
of the parameters are in-sync.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Reported-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Until we synchronize against device removal this limits the damage of
use after free bugs to the driver's own objects.  Unless we implement
reference counting we need to ensure at least a subset of a remote
device is valid at all times.  We follow the lead of other libsas
drivers that also preallocate devices.

This also enforces maximum remote device accounting at the lldd layer,
but the core may still run out of RNC's before we hit this limit.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Removed all callbacks in the deprecated.c. Core will call the appropriate
functions directly.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Renaming the callbacks to apparopriate event notify calls for the LLDD.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

We can copy the data directly to and from sg for SATA PIO read operations.
There is no reason to involve the hardware SGL. In the process we also need
to kmap the sg because we don't know where that can come from.

We also do to not call phys_to_virt(). The driver already has the information.
We can just calculcate the appropriate offets.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Moved the firmware loading from per adapter to per PCI device. This should
prevent firmware from being loaded twice becuase of 2 SCU controller per
PCI device. We do have to do it per PCI device because request_firmware()
requires a struct device passed in.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Add basic support for handling/reporting error interrupts.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The indirection is unecessary and broken in the current case that assigns the
handlers based on a not up-to-date pdev->msix_enabled value.

Route the handlers directly to the requisite core routines.

Todo: hook up error interrupt handling
Reported-by: NJeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NEdmund Nadolski <edmund.nadolski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

We no longer use the loglevel parameter. Remove.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Signed-off-by: NEdmund Nadolski <edmund.nadolski@intel.com>
[rebased after killing SCI_IO_REQUEST_DATA_DIRECTION]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Support for the up to 2x4-port 6Gb/s SAS controllers embedded in the
chipset.

This is a snapshot of the first publicly available version of the driver,
commit 4c1db2d0 in the 'historical' branch.

   git://git.kernel.org/pub/scm/linux/kernel/git/djbw/isci.git historical
Signed-off-by: NMaciej Trela <maciej.trela@intel.com>
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NEdmund Nadolski <edmund.nadolski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>