In clean_mr error path the 'mr' should be freed.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

mlx5 compatible devices have two ways of populating the MTT
table of an MKEY: using a FW command and using a UMR WQE.

A UMR is much faster, so it should be used whenever possible.
Unfortunately the code today uses UMR only if the MKEY was allocated
from the MR cache.

Fix the code to use UMR even for MKEYs that were allocated using
a FW command.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch is the first step in decoupling UMR usage and
allocation from the MR cache. The only functional change
in this patch is to enables UMR for MRs created with
reg_create.

This change fixes a bug where ODP memory regions that
were not allocated from the MR cache did not have UMR
enabled.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When we have a miss in one order of the mkey cache, we try to get
an mkey from a higher order.

We still need to check that the higher order can be used with UMR
before using it. Otherwise, we will get an mkey with 0 entries and
the post send operation that is used to fill it will complete with
the following error:

mlx5_0:dump_cqe:275:(pid 0): dump error cqe
00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000000 0f007806 25000025 49ce59d2

Fixes: 49780d42 ("IB/mlx5: Expose MR cache for mlx5_ib")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Reviewed-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

"umem" is a valid pointer.  We intended to print "*umem" or even just
"err" instead.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The failure in creation of debugfs entries for mr_cache left entries,
which were already created.

It caused to mismatch and misguiding for the end users. The solution
is to clean mr_cache debugfs root, so no leftovers will be in the
system. In addition, let's document why the error is not needed to be
forwarded to user in case of failure.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

ib_map_mr_sg() can pass an SG-list to .map_mr_sg() that is larger
than what fits into a single MR. .map_mr_sg() must not attempt to
map more SG-list elements than what fits into a single MR.
Hence make sure that mlx5_ib_sg_to_klms() does not write outside
the MR klms[] array.

Fixes: b005d316 ("mlx5: Add arbitrary sg list support")
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NMax Gurtovoy <maxg@mellanox.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Israel Rukshin <israelr@mellanox.com>
Cc: <stable@vger.kernel.org>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Commit a7c3e901 ("mm: introduce kv[mz]alloc helpers") added
proper implementation of mlx5_vzalloc function to the MM core.

This made the mlx5_vzalloc function useless, so let's remove it.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In case we got an initial sg_offset, we need to
account for it in the mr length.

Cc: stable@vger.kernel.org
Fixes: ff2ba993 ("IB/core: Add passing an offset into the SG to
ib_map_mr_sg")
Signed-off-by: NSagi Grimberg <sagi@grimberg.me>
Tested-by: NIsrael Rukshin <israelr@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Internally MW implemented as KLM MKey and filled by userspace UMR
postsends.  Handle pagefault trigered by operations on this MKeys.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Translation table updates of large UMR may require multiple post send
operations. The last operations can be in various lengths, but current
code set them to be the same length.

Fixes: 7d0cc6ed ('IB/mlx5: Add MR cache for large UMR regions')
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In memory shortage path we fall back to use spare buffer.
mlx5_ib_update_xlt() called from ib_uverbs_reg_mr when ibmr.ucontext
not initialized yet.

Scenario how to test it:
1. trigger memory exhaustion so __get_free_pages(GFP_KERNEL, 4) will fail
2. register MR
3. there should be no kernel oops

Fixes: 7d0cc6ed ('IB/mlx5: Add MR cache for large UMR regions')
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add implicit MR, covering entire user address space.
The MR is implemented as an indirect KSM MR consisting of
1GB direct MRs.
Pages and direct MRs are added/removed to MR by ODP.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Allow other parts of mlx5_ib to use MR cache mechanism.
* Add new functions mlx5_mr_cache_alloc and mlx5_mr_cache_free
* Traditional MTT MKey buckets are limited by MAX_UMR_CACHE_ENTRY
  Additinal buckets may be added above.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add "type" field to mlx5_core MKEY struct.
Check whether page fault happens on MKEY corresponding to MR.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this change we turn mlx5_ib_update_mtt() into generic
mlx5_ib_update_xlt() to perfrom HCA translation table modifiactions
supporting both atomic and process contexts and not limited by number
of modified entries.
Using this function we increase preallocated MRs up to 16GB.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of extended UMR translation offset.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* Update struct mlx5_wqe_umr_ctrl_seg.
* Currenlty UMR send_flags aim only certain use cases: enabled/disable
  cached MR, modifying XLT for ODP. By making flags independent make UMR
  more flexible allowing arbitrary manipulations.
* Since different UMR formats have different entry sizes UMR request
  should receive exact size of translation table update instead of
  number of entries. Rename field npages to xlt_size in struct mlx5_umr_wr
  and update relevant code accordingly.
* Add support of length64 bit.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up the following common code (to post a list of work requests to the
send queue of the specified QP) at various places and add a helper function
'mlx5_ib_post_send_wait' to implement the same.

 - Initialize 'mlx5_ib_umr_context' on stack
 - Assign "mlx5_umr_wr:wr:wr_cqe to umr_context.cqe
 - Acquire the semaphore
 - call ib_post_send with a single ib_send_wr
 - wait_for_completion()
 - Check for umr_context.status
 - Release the semaphore
Signed-off-by: NBinoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get a false-positive warning in linux-next for the mlx5 driver:

infiniband/hw/mlx5/mr.c: In function ‘mlx5_ib_reg_user_mr’:
infiniband/hw/mlx5/mr.c:1172:5: error: ‘order’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
infiniband/hw/mlx5/mr.c:1161:6: note: ‘order’ was declared here
infiniband/hw/mlx5/mr.c:1173:6: error: ‘ncont’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
infiniband/hw/mlx5/mr.c:1160:6: note: ‘ncont’ was declared here
infiniband/hw/mlx5/mr.c:1173:6: error: ‘page_shift’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
infiniband/hw/mlx5/mr.c:1158:6: note: ‘page_shift’ was declared here
infiniband/hw/mlx5/mr.c:1143:13: error: ‘npages’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
infiniband/hw/mlx5/mr.c:1159:6: note: ‘npages’ was declared here

I had a trivial workaround for gcc-5 or higher, but that didn't work
on gcc-4.9 unfortunately.

The only way I found to avoid the warnings for gcc-4.9, short of
initializing each of the arguments first was to change the calling
conventions to separate the error code from the umem pointer. This
avoids casting the error codes from one pointer to another incompatible
pointer, and lets gcc figure out when that the data is actually valid
whenever we return successfully.
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When enabling many VFs, the total amount of DMA mappings increase
significantly. This causes DMA allocations to take a lot of time
since they are serialized in the kernel.

As a result the driver enters into fatal condition due to
timeout and the system hangs. To recover from this we disable
MR cache for VFs.

PFs will still have a full cache and VFs cache can be manipulated
as usual after driver load.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The maximum page size in the mkey context is 2GB.

Until today, we didn't enforce this requirement in the code,
and therefore, if we got a page size larger than 2GB, we
have passed zeros in the log_page_shift instead of the actual value
and the registration failed.

This patch limits the driver to use compound pages of 2GB for mkeys.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Wait before continuing unload till all pending mkey async creation requests
are done.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When calling reg_mr of large MRs (e.g. 4GB) from multiple processes
and MR caches can't supply the required amount of MRs the slow-path
of MR allocation may be used. In this case we need to serialize the
slow-path between the processes to avoid soft lock.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Reviewed-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch decouples and moves vendors specific structures to
common UAPI folder which will be visible to all consumers.

These structures are used by user-space library driver
(libmlx5) and currently manually copied to that library.

This move will allow cross-compile against these files and
simplify introduction of vendor specific data.
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

alloc_ordered_workqueue() with WQ_MEM_RECLAIM set, replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.

The workqueue "cache->wq" queues work items &ent->work (maps to
cache_work_func) and &ent->dwork(maps to delayed_cache_work_func).
It has been identity converted.

WQ_MEM_RECLAIM has been set to ensure forward progress under
memory pressure.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove old representation of manually created MKey/PSV commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

The driver exposes interfaces that directly relate to HW state.
Upon fatal error, consumers of these interfaces (ULPs) that rely
on completion of all their posted work-request could hang, thereby
introducing dependencies in shutdown order. To prevent this from
happening, we manage the relevant resources (CQs, QPs) that are used
by the device. Upon a fatal error, we now generate simulated
completions for outstanding WQEs that were not completed at the
time the HW was reset.

It includes invoking the completion event handler for all involved
CQs so that the ULPs will poll those CQs. When polled we return
simulated CQEs with IB_WC_WR_FLUSH_ERR return code enabling ULPs
to clean up their  resources and not wait forever for completions
upon receiving remove_one.

The above change requires an extra check in the data path to make
sure that when device is in error state, the simulated CQEs will
be returned and no further WQEs will be posted.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The SRP initiator allows to set max_sectors to a value that exceeds
the largest amount of data that can be mapped at once with an mlx4
HCA using fast registration and a page size of 4 KB. Hence modify
ib_map_mr_sg() such that it can map partial sg-elements. If an
sg-element has been mapped partially, let the caller know
which fraction has been mapped by adjusting *sg_offset.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Tested-by: NLaurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Tested-by: NSteve Wise <swise@opengridcomputing.com>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Allocate proper context for arbitrary scatterlist registration
If ib_alloc_mr is called with IB_MR_MAP_ARB_SG, the driver
allocate a private klm list instead of a private page list.
Set the UMR wqe correctly when posting the fast registration.

Also, expose device cap IB_DEVICE_MAP_ARB_SG according to the
device id (until we have a FW bit that correctly exposes it).
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

These three related functions can't agree whether to put the
umrwr on the stack dirty and then memset it, or to initialize
it on the stack.  Make them all agree.
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Simplifies the code, and makes it more fair vs other users by using a
softirq for polling.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHaggai Eran <haggaie@mellanox.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch adds user-space support for memory windows allocation and
deallocation. It also exposes the supported types via
query_device_caps verb.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Tested-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Mlx5's mkey mechanism is also used for memory windows.
The current code base uses MR (memory region) naming, which is
inaccurate. Changing MR to mkey in order to represent its different
usages more accurately.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch adds support for re-registration of memory regions in MLX5.
The functionality is basically the same as deregister followed by
register, but attempts to reuse the existing resources as much as
possible.
Original memory keys are kept if possible, saving the need to
communicate new ones to remote peers.
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In order to add re-registration of memory region, some logic was
extracted to separate functions:
- ODP related logic.
- Some of the UMR WQE preparation code.
- DMA mapping.
- Umem creation.
- Creating MKey using FW interface.
- MR fields assignments after successful creation.
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The remove_keys() logic is performed as garbage collection task. Such
task is intended to be run when no other active processes are running.

The need_resched() will return TRUE if there are user tasks to be
activated in near future.

In such case, we don't execute remove_keys() and postpone
the garbage collection work to try to run in next cycle,
in order to free CPU resources to other tasks.

The possible pseudo-code to trigger such scenario:
1. Allocate a lot of MR to fill the cache above the limit.
2. Wait a small amount of time "to calm" the system.
3. Start CPU extensive operations on multi-node cluster.
4. Expect performance degradation during MR cache shrink operation.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

No ULP uses it anymore, go ahead and remove it.
Keep only the local invalidate part of the handlers.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDoug Ledford <dledford@redhat.com>