Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 22 3月, 2006 3 次提交
  3. 02 2月, 2006 1 次提交
  5. 14 1月, 2006 1 次提交
  7. 13 1月, 2006 1 次提交
  9. 09 1月, 2006 1 次提交
    • R
      [PATCH] IRQ type flags · 9ded96f2
      由 Russell King 提交于 
      Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels.  For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.

Currently, ARM drivers do (eg) the following:

	err = request_irq(irq, ...);

	set_irq_type(irq, IRQT_RISING);

However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.

Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt.  The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.

Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like.  The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      9ded96f2
  11. 07 1月, 2006 1 次提交
  13. 06 1月, 2006 8 次提交
  15. 05 1月, 2006 1 次提交
  17. 13 12月, 2005 1 次提交
    • L
      [ARM] 3201/1: PXA27x: Prevent hangup during resume due to inadvertedly... · 1ee9530a
      由 Lothar Wassmann 提交于 
      [ARM] 3201/1: PXA27x: Prevent hangup during resume due to inadvertedly enabling MBREQ (replaces: 3198/1)

Patch from Lothar Wassmann

The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.

Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."

There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."

Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.

Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      1ee9530a
  19. 01 12月, 2005 1 次提交
  21. 29 11月, 2005 1 次提交
  23. 21 11月, 2005 1 次提交
  25. 16 11月, 2005 1 次提交
  27. 13 11月, 2005 5 次提交
  29. 11 11月, 2005 2 次提交
    • L
      [ARM] 3098/1: pxa2xx disable ssp irq · b216c018
      由 Liam Girdwood 提交于 
      Patch from Liam Girdwood

This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.

This patch replaces 2845/1

Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: NLiam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      b216c018
    • R
      [ARM] 3096/1: Add SharpSL Zaurus power and battery management core driver · 078abcf9
      由 Richard Purdie 提交于 
      Patch from Richard Purdie

This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.

The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.

Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      078abcf9
  31. 10 11月, 2005 1 次提交
  33. 09 11月, 2005 4 次提交
  35. 07 11月, 2005 1 次提交
  37. 06 11月, 2005 2 次提交
  39. 05 11月, 2005 1 次提交
  41. 02 11月, 2005 1 次提交
  43. 31 10月, 2005 1 次提交
    • T
      [PATCH] fix missing includes · 4e57b681
      由 Tim Schmielau 提交于 
      I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.

In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch.  This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other.  So if any
hunk rejects or gets in the way of other patches, just drop it.  My scripts
will pick it up again in the next round.
Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      4e57b681