Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: patches for v3.7 merge window

Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.

We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.

Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.

All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.

usb: dwc3: patches for v3.7 merge window

Some much needed changes for our dwc3 driver. First there's a
rework on the ep0 handling due to some Silicon issue we uncovered
which affects all users of this IP core (there's a missing
XferNotReady(DATA) event in some conditions). This issue which
show up as a SETUP transfers which wouldn't complete ever and
we would fail TD 7.06 of the Link Layer Test from USB-IF and
Lecroy's USB3 Exerciser.

We also fix a long standing bug regarding EP0 enable sequencing
where we weren't setting a particular bit (Ignore Sequence
Number). Since we never saw any problems caused by that, it
didn't deserve being sent to stable tree.

On this pull request we also fix Burst Size initialization which
should be done only in SuperSpeed and we were mistakenly setting
Burst Size to the maximum value on non-SuperSpeed mode. Again,
since we never saw any problems caused by that, we're not sending
this patch to stable.

There's also a memory ordering fix regarding usage of bitmaps in
dwc3 driver.

You will also find some sparse warnings fix, a fix for missed
isochronous packets when the endpoint is already busy, and a
fix for synchronization delay on dwc3_stop_active_transfer().

usb: xceiv: patches for v3.7 merge window

nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.

Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.

We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.

Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.

Merge tag 'gadget-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

usb: gadget: patches for v3.7 merge window

This pull request is large but the biggest part is the first part
of the cleanup on the gadget framework so we have a saner setup
to add configfs support for v3.8.

We have also some more conversions to the new udc_start/udc_stop
which makes us closer from dropping the old interfaces.

USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone,
thanks to Michal for his awesome work.

Other than that, we have the usual set of miscellaneous changes
and cleanups involving improvements to debug messages, removal
of duplicated includes, moving dereference after NULL test,
making renesas_hsbhs' irq handler Shared, unused code being dropped,
prevention of sleep-inside-spinlock bugs and a race condition fix
on udc-core.

As NOP device node is now added in am33xx tree so remove the call
which creates the NOP platform_device.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

AM335x and TI81xx platform has dual musb controller so updating the
musb_dspc.c to support the same.

Changes:
        - Moved otg_workaround timer to glue structure
        - Moved static local variable last_timer to glue structure
        - PHY on/off related cleanups
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
[afzal@ti.com: remove control module related modifications]
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Moved global variable "musb_debugfs_root" and static variable
"old_state" to 'struct musb' to help support multi instance of
musb controller as present on AM335x platform.

Also removed the global variable "orig_dma_mask" and filled the
dev->dma_mask with parent device's dma_mask.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added musb_ida in musb_core.c to manage the multi core ids.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The glue layer should directly write to mailbox register (present in
control module) instead of calling phy layer to write to mailbox
register. Writing to mailbox register notifies the core of events like
device connect/disconnect.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The mailbox register for usb otg in omap is present in control module.
On detection of any events VBUS or ID, this register should be written
to send the notification to musb core.

Till we have a separate control module driver to write to control module,
omap2430 will handle the register writes to control module by itself. So
a new address space to represent this control module register is added
to usb_otg_hs.
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Because the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated and in hardirq context the interrupt is disabled.

so in usb/host code:
Removing the usage of flag IRQF_DISABLED;
Removing the calling local_irq save/restore actions in irq
handler usb_hcd_irq();
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds two sysfs files for each usb hub port to allow userspace
to control the port power policy.

For an upcoming Intel xHCI roothub, this will translate into ACPI calls
to completely power off or power on the port.  As a reminder, when these
ports are completely powered off, the USB host and device will see a
physical disconnect.  All future USB device connections will be lost,
and the device will not be able to signal a remote wakeup.

The control sysfs file can be written to with two options:
"on" - port power must be on.
"off" - port must be off.

The state sysfs file reports usb port's power state:
"on" - powered on
"off" - powered off
"error" - can't get power state

For now, let userspace dictate the port power off policy.  Future
patches may add an in-kernel policy.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Alan Stern pointed out that a USB port could potentially get powered off
when the attached USB device is in the middle of enumerating, due to
race conditions:
	http://marc.info/?l=linux-usb&m=134130616707548&w=2

If that happens, we need to ensure the enumeration fails.  If a call to
usb_get_descriptor() fails for a reason other than a Stall, return an
error.  That should handle the case where the port is powered off.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off.  The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.

Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.

When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism.  If so, call into these new ACPI methods.  Also use the ACPI
methods when the USB core asks to power on a port.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes the xHCI roothub code handle the clear PORT_POWER
feature request.  Setting port power is already handled.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event.  Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.

According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible").  Here's a matrix of the
possible combinations:

Visible Connectible
		Name		Example
-------------------------------------------------------------------------

Yes	No	Unknown		(Invalid state.)

Yes	Yes	Hot-plug	USB ports on the outside of a laptop.
				A user could freely connect and disconnect
				USB devices.

No	Yes	Hard-wired	A USB modem hard-wired to a port on the
				inside of a laptop.

No	No	Not used	The port is internal to the system and
				will remain empty.

Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED.  When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the ACPI DSDT table, only usb root hub and usb ports are ACPI device
nodes.  Originally, we bound the usb port's ACPI node to the usb device
attached to the port.  However, we want to access those ACPI port
methods when the port is empty, and there's no usb_device associated
with that port.

Now that the usb port is a real device, we can bind the port's ACPI node
to struct usb_port instead.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there.  Instead, store the usb_device child
in its parent usb_port structure.

Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child().  Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.

Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch turns each USB port on a hub into a new struct device.  This
new device has the USB hub interface device as its parent.  The port
devices are stored in a new structure (usb_port), and an array of
usb_ports are dynamically allocated once we know how many ports the USB
hub has.

Move the port_owner variable out of usb_hub and into this new structure.

A new file will be created in the hub interface sysfs directory, so
add documentation.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

DeviceRemovalbe and wHubDelay for usb3.0 hub are little-endian
and so define them as _le16.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The kernel's version number is used as decimal in the bcdDevice field of
the RH descriptor. For kernel version v3.12 we would see 3.0c in lsusb.
I am not sure how important it is to stick with bcd values since this is
this way since we started git history and nobody complained (however back
then we reported only 2.6).
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In commit fb28d58b ("USB: remove CONFIG_USB_DEVICEFS") USBFS got
removed. Since it is gone we can stop using it in testusb and try udev
nodes right away.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Apps which deal with devices which also have a kernel driver, need to do
the following:
1) Check which driver is attached, so as to not detach the wrong driver
   (ie detaching usbfs while another instance of the app is using the device)
2) Detach the kernel driver
3) Claim the interface

Where moving from one step to the next for both 1-2 and 2-3 consists of
a (small) race window. So currently such apps are racy and people just live
with it.

This patch adds a new ioctl which makes it possible for apps to do this
in a race free manner. For flexibility apps can choose to:
1) Specify the driver to disconnect
2) Specify to disconnect any driver except for the one named by the app
3) Disconnect any driver

Note that if there is no driver attached, the ioctl will just act like the
regular claim-interface ioctl, this is by design, as returning an error for
this condition would open a new bag of race-conditions.

Changes in v2:
-Fix indentation of if blocks where the condition spans multiple lines
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fengguang Wu reported:
|drivers/usb/gadget/serial.c:89:22: sparse: cast truncates bits from
|constant value (24000000 becomes 0)

I obviously let the version number shift away. Since the version is a
16bit number it can be applied as it.

Cc: fengguang.wu@intel.com
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently mx23 fails to enumerate a USB device:

[ 1.300000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.520000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.740000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.960000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 2.180000] hub 1-0:1.0: unable to enumerate USB device on port 1

Use a kernel workqueue to asynchronously delay the setting of
ENHOSTDISCONDETECT bit until after higher level hub connect/reset processing
is complete.  Prematurely setting the bit prevents the connection
processing from completing and not setting it prevents disconnect from being
detected. No delay is needed for clearing of ENHOSTDISCONDETECT.

Successfully tested on mx23-olinuxino (micro, mini and maxi variants) and mx28evk.

Cc: stable@vger.kernel.org # v3.6
Signed-off-by: NMike Thompson <mpthompson@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will let us control PHYs on platforms which
need them.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.

Note that once OMAP's transceiver drivers reach mainline,
this glue layer will change accordingly.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dereference should be moved below the NULL test.

spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Spotted by Fengguang Wu:
|In file included from drivers/usb/gadget/ether.c:110:0:
|drivers/usb/gadget/u_ether.c:87:21: error: expected ')' before 'uint'
|drivers/usb/gadget/u_ether.c:88:25: error: expected ')' before string constant

This is because u_ether.c relied on having module.h included somewhere.
This isn't the case since composite.c is no longer included.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.

There are some driver in tree (on the host side) which use the bcdDevice
field to figure out special workarounds for a given firmware revision.
This seems to make sense. Therefore this patch converts all gadgets
(except a few) to use the kernel version instead a random 2 or 3 plus
the UDC number. The few that don't report kernel's version are:
- webcam
  This one reports always a version 0x10 so allow it to do so in future.
- nokia
  This one reports always 0x211. The comment says that this gadget works
  only if the UDC supports altsettings so I added a check for this.
- serial
  This one reports 0x2400 + UDC number. Since the gadget version is 2.4
  this could make sense. Therefore bcdDevice is 0x2400 here.

I also remove various gadget_is_<name> macros which are unused. The
remaining few macros should be moved to feature / bug bitfield.
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Don't fail the initialization check for the platform_data
if there is avaiable an associated device tree node.
Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dereference should be moved below the NULL test.

spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

MODULE_VERSION and AUTHOR looks better in composite.c than in
usbstrings.c so I move it there.
I put David Brownell as the module Author as I belive he wrote most of
it.
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This moves composite.c into libcomposite and updates all gadgets.
Finally!
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>