- 21 3月, 2007 5 次提交
-
-
由 Bernhard Walle 提交于
In sn_io_slot_fixup(), the parent is re-set from the bus to io(port|mem)_resource because the address is changed in a way that it's not child of the bus any more. However, only the root is set but not the parent/child/sibling relationship in the resource tree which causes 'cat /proc/iomem' to stop after this memory area. Depding on the poition in the tree the iomem may be nearly completely empty. Signed-off-by: NBernhard Walle <bwalle@suse.de> Acked-by: NJohn Keller <jpk@sgi.com> Signed-off-by: NTony Luck <tony.luck@intel.com>
-
由 John Keller 提交于
When booting an SN system without specifing a console (i.e., no "console=" on boot line), the system will hang during boot at the point where /sbin/init is run. The problem is that vga_console_iobase is not converted to a virtual address before storing in io_space[0].mmio_base. The conversion was happening in sn_scan_pcdp(), but not in setup_vga_console(). Signed-off-by: NJohn Keller <jpk@sgi.com> Signed-off-by: NTony Luck <tony.luck@intel.com>
-
由 Jay Lan 提交于
Clearly should be checking for "val == DIE_INIT_SLAVE_ENTER". Signed-off-by: NJay Lan <jlan@sgi.com> Acked-by: NSimon Horman <horms@verge.net.au> Signed-off-by: NTony Luck <tony.luck@intel.com>
-
由 Jack Steiner 提交于
If a system consists of mixed processor types, kmalloc() can be called before the per-cpu data page is initialized. If the slab contains sufficient memory, then kmalloc() works ok. However, if the slabs are empty, slab calls the memory allocator. This requires per-cpu data (NODE_DATA()) & the cpu dies. Also noted by Russ Anderson who had a very similar patch. Signed-off-by: NJack Steiner <steiner@sgi.com> Signed-off-by: NTony Luck <tony.luck@intel.com>
-
由 Zou Nan hai 提交于
We have seen bad_pte_print when testing crashdump on an SN machine in recent 2.6.20 kernel. There are tons of bad pte print (pfn < max_low_pfn) reports when the crash kernel boots up, all those reported bad pages are inside initmem range; That is because if the crash kernel code and data happens to be at the beginning of the 1st node. build_node_maps in discontig.c will bypass reserved regions with filter_rsvd_memory. Since min_low_pfn is calculated in build_node_map, so in this case, min_low_pfn will be greater than kernel code and data. Because pages inside initmem are freed and reused later, we saw pfn_valid check fail on those pages. I think this theoretically happen on a normal kernel. When I check min_low_pfn and max_low_pfn calculation in contig.c and discontig.c. I found more issues than this. 1. min_low_pfn and max_low_pfn calculation is inconsistent between contig.c and discontig.c, min_low_pfn is calculated as the first page number of boot memmap in contig.c (Why? Though this may work at the most of the time, I don't think it is the right logic). It is calculated as the lowest physical memory page number bypass reserved regions in discontig.c. max_low_pfn is calculated include reserved regions in contig.c. It is calculated exclude reserved regions in discontig.c. 2. If kernel code and data region is happen to be at the begin or the end of physical memory, when min_low_pfn and max_low_pfn calculation is bypassed kernel code and data, pages in initmem will report bad. 3. initrd is also in reserved regions, if it is at the begin or at the end of physical memory, kernel will refuse to reuse the memory. Because the virt_addr_valid check in free_initrd_mem. So it is better to fix and clean up those issues. Calculate min_low_pfn and max_low_pfn in a consistent way. Signed-off-by: NZou Nan hai <nanhai.zou@intel.com> Acked-by: NJay Lan <jlan@sgi.com> Signed-off-by: NTony Luck <tony.luck@intel.com>
-
- 11 3月, 2007 1 次提交
-
-
由 Linus Torvalds 提交于
This reverts commit d2487cb4. Russell King points out that it's obviously bogus, and I have to agree. Not only does "irq" not even exist in that scope, but we obviously need to free the irq that we actually requested, and that's IRQ_USB. Reported-by: NRussell King <rmk@arm.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <greg@kroah.com> Cc: David Brownell <david-b@pacbell.net>, Cc: Milan Svoboda <msvoboda@ra.rockwell.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 10 3月, 2007 34 次提交
-
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [IPV6] fix ipv6_getsockopt_sticky copy_to_user leak [IPV6]: Fix for ipv6_setsockopt NULL dereference [DCCP]: Initialise write_xmit_timer also on passive sockets [IPV4]: Fix rtm_to_ifaddr() error handling.
-
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6由 Linus Torvalds 提交于
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] refresh config files [IA64] put kdump_find_rsvd_region in __init [IA64] Remove sparse warning from unwind code [IA64] add missing syscall trace clear [IA64] Cleanup in crash.c [IA64] kexec: declare ia64_mca_pal_base in mca.h rather than kexec.h [IA64] pci_get_legacy_ide_irq should return irq (not GSI) [IA64] whitespace fixes for include/asm-ia64/sal.h [IA64] Cache error recovery [IA64] Proper handling of TLB errors from duplicate itr.d dropins
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: kobject: new_device->kref wasn't putted after error in kobject_move() driver core: export device_rename Remove devfs from MAINTAINERS Driver core: add device symlink back to sysfs Revert "driver core: refcounting fix"
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: pci: fix section mismatch warning PCI: aer: fix section mismatch warning pcie: fix section mismatch warning PCI: allow multiple calls to pcim_pin_device()
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits) USB Elan FTDI: check for workqueue creation USB: fix spinlock recursion in cdc-acm.c USB: fix Unaligned access in EHCI driver USB: Product ID for FT232RL in ftdi_sio USBNET: DM9501: Add Corega FEther USB-TXC support. USB: ipaq.c: Additional devices USB: further fix for usb-serial USB: fix usb-serial device naming bug USB: RTS/DTR signal patch for airprime driver USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer usb-serial: fix shutdown / device_unregister order USB: add Additional PIDs in ftdi_sio USB: add QL355P power supply ids to fdti_sio USB: New device IDs for cp2101 driver USB: kill dead code from hub.c USB: ratelimit debounce error messages USB: pxa2xx_udc: fix hardcoded irq number UHCI: fix port resume problem USB: set the correct interval for interrupt URBs USB: goku_udc: Remove crude cache coherency code ...
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Alexey Starikovskiy 提交于
Delay the read of the EC status register until after the event that caused it occurs -- otherwise it is possible to read and act on stale status that was associated with the previous event. Do this with a perpetually incrementing "event_count" to detect when a new event occurs and it is safe to read status. There is no workaround for polling mode -- it is inherently exposed to reading and acting on stale status, since it doesn't have an interrupt to tell it the event completed. http://bugzilla.kernel.org/show_bug.cgi?id=8110Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Cyrill Gorcunov 提交于
Avoid NULL pointer usage if workqueue creation failed. Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com> Cc: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
this fixes the spinlock recursion issue. The older fix was incomplete. Signed-off-by: NOliver Neukum <oneukum@suse.de> Acked-by: NPete Zaitcev <zaitcev@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Max Dmitrichenko 提交于
I get following warnings on spar64: Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd] Despite of the comment in the patched code, the type cast used there does make unaligned access. The fix was made as it's done in ohci-hub.c. Signed-off-by: NMax Dmitrichenko <dmitrmax@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Gard Spreemann 提交于
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch generates a warning during compilation because get_ftdi_divisor doesn't explicitly handle the FT232RL with this patch, so I guess you don't want to use it in its current state. It is all I could come up with with the knowledge I have of the drivers at the moment, though, and I hope you can have some use for it at least. It works fine with my DLP-TILT with an FT232RL. From: Gard Spreemann <spreeman@stud.ntnu.no> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 YOSHIFUJI Hideaki 提交于
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Andre Spahlinger 提交于
Additional devices Signed-off-by: NAndre Spahlinger <uenz@gmx.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
this is a fix for the outstanding usb-serial issues. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter: > Hi Greg > > 34ef50e5 is definitely > the source of the problem. Reverting that makes the > ftdi port show up as ttyUSB0 again for me and it > can actually be opened. This patch should fix the issue. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NCraig Schlenter <craig@codefountain.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Schiller 提交于
I encountered some problems with the airprime driver in use with a Novatel Merlin XU870: Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the RTS/DTR lines of the Modem. Consequently, when I use minicom to establish a connection by "ATD*99#" the modem doesn't hang up even if i exit minicom and so I cannot reuse the modem unless I remove it and plug it in again. With the attached patch, the RTS/DTR lines are resetted on a close. The code was mainly taken from the option.c driver.
-
由 Jim Radford 提交于
Convert all the port specific code in attach / shutdown to use the new port_probe / port_register callbacks from device_register / device_unregister allowing adding the sysfs attributes to be added at the correct time and to the serial port device itself, instead of to the unadorned usb device, avoiding a NULL dereference. Signed-off-by: NJim Radford <radford@blackbean.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jim Radford 提交于
Ensure that the ->port_remove() callbacks get called before the ->shutdown() callback which makeing the order symmetric with ->attach() being called before ->port_probe(). Signed-off-by: NJim Radford <radford@blackbean.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Thomas Schleusener 提交于
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind to give some own PID's which I can use together with their VID. Some of the devices are already very popular here and I have customers from universities, institutes ..... I use the FTDI VID 0x0403. My PID's are: 0xff38 - IBS US485 (USB<-->RS422/485 interface) 0xff39 - IBS PIC-Programmer 0xff3a - IBS Card reader for PCMCIA SRAM-cards 0xff3b - IBS PK1 - Particel counter 0xff3c - IBS RS232 - Monitor 0xff3d - APP 70 (dust monitoring system) 0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz) 0xff3f - future device The company is "IBS Ing.-Buero Schleusener". From: Thomas Schleusener <thomas@be-schl.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Michael Olberg 提交于
-
由 Jon K Hellan 提交于
Here are two new device IDs for the cp2101 driver. The diff is with linus's tree as of this evending. From: Jon K Hellan <hellan@acm.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
this kills residual obsoletet code from hub.c Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
flaky hardware can cause a lot of debounce failed messages. To limit the performance impact, a ratelimit should be used. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Milan Svoboda 提交于
This patch changes last use of hardcoded number of irq to use platfrom_get_irq. Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com> Acked-by: NDavid Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as863) fixes a problem encountered sometimes when resuming a port on a UHCI controller. The hardware may turn off the Resume-Detect bit before turning off the Suspend bit, leading usbcore to think that the port is still suspended and the resume has failed. The patch makes uhci_finish_suspend() wait until both bits are safely off. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-