Enable filters for non-offload configuration and add common api support
for setting and deleting filters in LE-TCAM region of the hardware.

IPv4 filters occupy one slot.  IPv6 filters occupy 4 slots and must
be on a 4-slot boundary.  IPv4 filters can not occupy a slot belonging
to IPv6 and the vice-versa is also true.

Filters are set and deleted asynchronously.  Use completion to wait
for reply from firmware in order to allow for synchronization if needed.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move common filter code to separate files.  Also fix the following
checkpatch checks.

CHECK: Comparison to NULL could be written "!f->l2t"
+               if (f->l2t == NULL) {

CHECK: spaces preferred around that '/' (ctx:VxV)
+       fwr->len16_pkd = htonl(FW_WR_LEN16_V(sizeof(*fwr)/16));
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When switching from polling-based fw commands to event-based fw
commands, there is a race condition which could cause a fw command
in another task to hang: that task will keep waiting for the polling
sempahore, but may never be able to acquire it. This is due to
mlx4_cmd_use_events, which "down"s the sempahore back to 0.

During driver initialization, this is not a problem, since no other
tasks which invoke FW commands are active.

However, there is a problem if the driver switches to polling mode
and then back to event mode during normal operation.

The "test_interrupts" feature does exactly that.
Running "ethtool -t <eth device> offline" causes the PF driver to
temporarily switch to polling mode, and then back to event mode.
(Note that for VF drivers, such switching is not performed).

Fix this by adding a read-write semaphore for protection when
switching between modes.

Fixes: 225c7b1f ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Radix tree lookup can be performed without locking.

Fixes: 225c7b1f ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Suggested-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use tabs instead of spaces before if statement, no functional change.

Fixes: e7c1c2c4 ("mlx4_en: Added self diagnostics test implementation")
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add likely/unlikely hints to improve branch predictions
in the RX data-path.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add offload of TC in direct action mode.  We just need
to provide appropriate checks in the verifier and
a new outro block to translate the exit codes to what
data path expects
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Data path has redirect support so expressing redirect
to the port frame came from is a trivial matter of
setting the right result code.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing ABI defines and eBPF instructions to allow
mark to be passed on and extend prepend parsing on the
RX path to pick it up from packet metadata.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Periodically poll stats and call into offloaded actions
to update them.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add hardware bpf offload on our smart NICs.  Detect if
capable firmware is loaded and use it to load the code JITed
with just added translator onto programmable engines.

This commit only supports offloading cls_bpf in legacy mode
(non-direct action).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add translator for JITing eBPF to operations which
can be executed on NFP's programmable engines.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace max rif const with using the result from resource query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the max number of rif (router interfaces) to resource query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add max system ports, max regions and max vlan groups to resource query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace max virtual routers const with the result from
the resource query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the max number of virtual routers to resource query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use resources from resource query to determine values for
the profile configuration.
Add KVD determined section sizes to the resources struct.
Change the profile struct and value to match this changes.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add KVD size, and minimum sizes for the single and double
sections resources to resources query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use max lag and max ports in lag resources as the result of resource query
instead of using const to save them.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add max lag and max ports in lag resources to resources query.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The offloads stats functions are local to this file, make them static.

Fixes: fc1bbb0f ('mlxsw: spectrum: Implement offload stats ndo [..]')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

data_src is unchanged inside the loop, so this patch moves
the assignment to outside the loop to avoid unnecessarily
assignment
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct drop handling for XDP_TX on TX failure, were recently added in
commit 95357907 ("mlx4: fix XDP_TX is acting like XDP_PASS on TX
ring full").

The change missed an opportunity for recycling the RX page, instead of
going through the page allocator, like the regular XDP_DROP action does.
This patch cease the opportunity, by going through the XDP_DROP case.

Fixes: 95357907 ("mlx4: fix XDP_TX is acting like XDP_PASS on TX ring full")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/mellanox/mlxsw//spectrum.c:251:28: warning: symbol
'mlxsw_sp_span_entry_find' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:265:28: warning: symbol
'mlxsw_sp_span_entry_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: warning: mixing
different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56:     int enum
mlxsw_sp_span_type  versus
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56:     int enum
mlxsw_reg_mpar_i_e
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32:     int
enum mlxsw_reg_sbxx_dir  versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32:     int
enum devlink_sb_pool_type
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39:     int
enum mlxsw_reg_sbpr_mode  versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39:     int
enum devlink_sb_threshold_type
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54:     int
enum mlxsw_sp_l3proto  versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54:     int
enum mlxsw_reg_ralxx_protocol
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1749:6: warning:
symbol 'mlxsw_sp_fib_entry_put' was not declared. Should it be static?
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the RX hash function from XOR to CRC in order to have better
distribution of the traffic.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_hwrm_fw_set_time() now returns -EOPNOTSUPP when built for kernel
without RTC_LIB.  Setting the firmware time is not critical to the
successful completion of the firmware update process.
Signed-off-by: NRob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c:463:5: warning: no previous prototype for 'esw_offloads_init' [-Wmissing-prototypes]
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c:521:6: warning: no previous prototype for 'esw_offloads_cleanup' [-Wmissing-prototypes]

In fact, both functions are declared in
drivers/net/ethernet/mellanox/mlx5/core/eswitch.c,but should be
declared in a header file, thus can be recognized in other file.

So this patch moves the declarations into
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/emulex/benet/be_main.c:4368:6: warning: no previous prototype for 'be_calculate_pf_pool_rss_tables' [-Wmissing-prototypes]
drivers/net/ethernet/emulex/benet/be_cmds.c:4385:5: warning: no previous prototype for 'be_get_nic_pf_num_list' [-Wmissing-prototypes]
drivers/net/ethernet/emulex/benet/be_cmds.c:4537:6: warning: no previous prototype for 'be_reset_nic_desc' [-Wmissing-prototypes]
drivers/net/ethernet/emulex/benet/be_cmds.c:4910:5: warning: no previous prototype for '__be_cmd_set_logical_link_config' [-Wmissing-prototypes]

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF link state can be changed via the 'ip link set' cmd.
Currently, the new link state does not take effect immediately.

The fix is for the PF to send a link change async event to the
designated VF after a VF link state change.  This async event will
trigger the VF to update the link status.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restart autoneg if autoneg is enabled.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware has a limitation that it won't pass host to BMC loopback
packets below 52-bytes.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After generating the random MAC address for VF, call the firmware to
approve it.  This step serves 2 purposes.  Some hypervisor (e.g. ESX)
wants to approve the MAC address.  2nd, the call will setup the
proper forwarding database in the internal switch.

We need to unlock the hwrm_cmd_lock mutex before calling bnxt_approve_mac().
We can do that because we are at the end of the function and all the
previous firmware response data has been copied.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-arrange the code so that the generation of the random MAC address for
the VF is at the end of the function.  The next patch will add one more step
to call bnxt_approve_mac() to get the firmware to approve the random MAC
address.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing code is inconsistent in reporting and accepting the combined
channel count.  bnxt_get_channels() reports maximum combined as the
maximum rx count.  bnxt_set_channels() accepts combined count that
cannot be bigger than max rx or max tx.

For example, if max rx = 2 and max tx = 1, we report max supported
combined to be 2.  But if the user tries to set combined to 2, it will
fail because 2 is bigger than max tx which is 1.

Fix the code to be consistent.  Max allowed combined = max(max_rx, max_tx).
We will accept a combined channel count <= max(max_rx, max_tx).
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>